Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2012.12–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0050193 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area

*: w/ Stop and Start System

Main Body ECU Communication Stop Mode Either condition is met:
·

"Main Body" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Main Body ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside main body ECU (multiplex network body ECU)

·

Main body ECU (multiplex network body ECU) CAN branch wire or connector

·

Main body ECU (multiplex network body ECU)

·

Instrument panel junction block assembly

·

Engine stop and start ECU*



WIRING DIAGRAM

C277458E01
5.333,8.083 7.01,8.417 1.677,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 5.667,7.177 6.698,7.375 1.031,0.198 10 false GND1 5.667,6 6.698,6.198 1.031,0.198 10 false IG 5.667,3.333 6.698,3.531 1.031,0.198 10 false ACC 5.667,2.635 6.698,2.833 1.031,0.198 10 false BECU 5.677,0.688 6.708,0.885 1.031,0.198 10 false CANH 5.667,1.333 6.698,1.531 1.031,0.198 10 false CANL 1.719,1.219 2.75,1.417 1.031,0.198 10 false 2 1.719,0.552 2.75,0.75 1.031,0.198 10 false 1 0.333,1.667 1.365,1.865 1.031,0.198 10 false G123 0.333,1.833 2.365,2.031 2.031,0.198 10 false No. 1 CAN Junction Connector 0.75,2.625 2.781,2.823 2.031,0.198 10 false from Battery 0.75,3.302 2.781,3.5 2.031,0.198 10 false from Battery 0.083,4 1.552,4.406 1.469,0.406 10 false from Certification ECU*1 or Ignition Switch*2 0.25,4.917 2.281,5.115 2.031,0.198 10 false from IG1 NO.1 Relay 1.885,4.75 3.917,4.948 2.031,0.198 10 false ECU-IG NO.2 0.135,6.667 2.167,6.865 2.031,0.198 10 false Engine Stop and Start ECU*4 0.135,6.5 2.167,6.698 2.031,0.198 10 false G87 0.906,5.969 1.354,6.198 0.448,0.229 10 false IGO1 1.333,5.833 1.667,6 0.333,0.167 10 false 12 2.833,5.417 3.167,5.583 0.333,0.167 10 false *3 2.083,5.833 2.417,6 0.333,0.167 10 false *4 3.323,5.969 3.656,6.135 0.333,0.167 10 false 3D 3.313,5.729 3.646,5.896 0.333,0.167 10 false 40 2.052,2.469 4.083,2.667 2.031,0.198 10 false ECU-B NO.1 3.313,7.167 3.646,7.333 0.333,0.167 10 false 3D 3.365,6.906 3.698,7.073 0.333,0.167 10 false 9 3.333,4 3.667,4.167 0.333,0.167 10 false 3C 3.333,3.75 3.667,3.917 0.333,0.167 10 false 45 3.365,3.073 3.698,3.24 0.333,0.167 10 false 1 3.333,3.323 3.667,3.49 0.333,0.167 10 false 3A 3.323,2.615 3.656,2.781 0.333,0.167 10 false 3B 3.323,2.365 3.656,2.531 0.333,0.167 10 false 16 4.698,3.156 5.729,3.354 1.031,0.198 10 false ACC 3.99,4.26 5.021,4.458 1.031,0.198 10 false ACC 0.135,7.5 2.167,7.698 2.031,0.198 10 false *1: w/ Entry and Start System 0.135,7.833 2.167,8.031 2.031,0.198 10 false *2: w/o Entry and Start System 0.135,8.135 2.167,8.333 2.031,0.198 10 false *3: w/o Stop and Start System 0.135,8.469 2.167,8.667 2.031,0.198 10 false *4: w/ Stop and Start System 5.292,1.073 5.625,1.24 0.333,0.167 10 false 13 5.302,0.417 5.635,0.583 0.333,0.167 10 false 14 5.25,1.333 5.583,1.5 0.333,0.167 10 false G78 5.25,0.688 5.583,0.854 0.333,0.167 10 false G78 3.25,8.083 4.854,8.458 1.604,0.375 10 false Instrument Panel Junction Block Assembly 5.333,7.167 5.667,7.333 0.333,0.167 10 false A 5.302,6.948 5.635,7.115 0.333,0.167 10 false 11 5.323,5.958 5.656,6.125 0.333,0.167 10 false A 5.323,3.313 5.656,3.479 0.333,0.167 10 false A 5.333,2.615 5.667,2.781 0.333,0.167 10 false A 5.292,5.74 5.625,5.906 0.333,0.167 10 false 32 5.271,3.073 5.604,3.24 0.333,0.167 10 false 29 5.302,2.375 5.635,2.542 0.333,0.167 10 false 30

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Wait 20 seconds after turning the ignition switch ACC or ON.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU CAN BRANCH WIRE)
a.
C212975C04
0.344,1.073 0.813,1.333 0.469,0.26 1.167,0.417 1.333,0.417 1.333,0.417 1.604,1.177 true 1.542,1.177 1.083,0.667 1.083,0.667 0.917,0.667 true 0.073,0.052 0.313,0.24 0.24,0.188 10 *a 0.5,0.594 0.927,0.75 0.427,0.156 10 CANH 0.75,0.333 1.156,0.49 0.406,0.156 10 CANL 0.438,1.135 0.771,1.292 0.333,0.156 10 G78
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G78-14 (CANH) - G78-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE MAIN BODY ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.
C227508C04
1.344,0.438 1.771,0.688 0.427,0.25 2.448,1.406 2.677,1.406 2.677,1.406 2.813,1.125 true 2.417,0.74 2.667,0.74 2.667,0.74 2.927,1.094 true 2.604,0.521 2.854,0.521 2.854,0.521 3.094,1.115 true 0.708,0.74 0.958,0.74 0.958,0.74 1.219,1.094 true 1.531,0.49 1.688,0.688 0.156,0.198 10 A 0.104,0.104 0.354,0.344 0.25,0.24 10 *a 1.99,0.677 2.51,0.865 0.521,0.188 10 BECU 0.323,0.656 0.844,0.844 0.521,0.188 10 GND1 2.417,0.458 2.938,0.646 0.521,0.188 10 IG 2.115,1.323 2.635,1.51 0.521,0.188 10 ACC
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


c.

Reconnect the 3A, 3B, 3C and 3D instrument panel junction block assembly connectors.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-30 (BECU) - Body ground Always 11 to 14 V
A-32 (IG) - Body ground Ignition switch ON 11 to 14 V
A-29 (ACC) - Body ground Ignition switch ACC 11 to 14 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-11 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connectors.

C278742C01
1.75,0.292 2.135,0.552 0.385,0.26 4.906,0.292 5.292,0.552 0.385,0.26 5.104,2.125 5.49,2.385 0.385,0.26 1.719,2.104 2.104,2.365 0.385,0.26 1.844,0.344 2.156,0.542 0.313,0.198 10 3A 5.01,0.344 5.323,0.542 0.313,0.198 10 3B 1.823,2.156 2.135,2.354 0.313,0.198 10 3C 5.198,2.167 5.51,2.365 0.313,0.198 10 3D 0.167,0.135 0.479,0.333 0.313,0.198 10 *a
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V
3B-16 - Body ground Always 11 to 14 V
3C-45 - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-9 - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
a.
C277457C01
1.417,0.333 1.833,0.583 0.417,0.25 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 1.521,0.385 1.833,0.542 0.313,0.156 10 3D
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3D-40 - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE STOP AND START ECU)
5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-40 - G87-12 (IGO1) Always Below 1 Ω
3D-40 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR