Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2012.12–2013.11
RM3090E _57 Power Source / Network _008434 NETWORKING _0050193 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area

*: w/ Stop and Start System

Navigation ECU Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Navigation ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside navigation ECU sub-assembly

·

Navigation ECU sub-assembly CAN branch wire or connector

·

Navigation ECU sub-assembly

·

Engine stop and start ECU*



For vehicles with a navigation receiver type.


WIRING DIAGRAM

C277479E03
0.25,7.052 4.375,7.25 4.125,0.198 10 *1: w/o Stop and Start System 0.25,7.385 4.375,7.583 4.125,0.198 10 *2: w/ Stop and Start System 5.135,7.135 7.052,7.354 1.917,0.219 10 Navigation ECU Sub-assembly 0.333,1.552 2,1.75 1.667,0.198 10 G130 0.333,1.719 2.5,1.917 2.167,0.198 10 No. 2 CAN Junction Connector 0.583,2.385 2.75,2.583 2.167,0.198 10 from IG1 NO.1 Relay 2.823,2.219 3.74,2.667 0.917,0.448 10 ECU-IG NO.2 1.094,3.198 3.26,3.396 2.167,0.198 10 from Battery 2.969,3.052 3.885,3.5 0.917,0.448 10 RADIO 3.042,5.208 3.958,5.656 0.917,0.448 10 ACC 0.875,5.375 2.208,5.625 1.333,0.25 10 from ACC Relay 3.583,3.083 4.5,3.531 0.917,0.448 10 *1 2.917,3.719 3.833,4.167 0.917,0.448 10 *2 2.917,4.219 3.833,4.667 0.917,0.448 10 *2 3.583,5.219 4.5,5.667 0.917,0.448 10 *1 0.417,4.667 1.75,4.917 1.333,0.25 10 G87 0.417,4.833 3.083,5.083 2.667,0.25 10 Engine Stop and Start ECU*2 1.667,3.75 2.583,4.198 0.917,0.448 10 2 1.667,4.219 2.583,4.667 0.917,0.448 10 3 1.24,3.833 2.156,4.281 0.917,0.448 10 BO1 1.25,4.333 2.167,4.781 0.917,0.448 10 ACO 5.667,4.365 6.583,4.813 0.917,0.448 10 ACC1 5.667,3.208 6.583,3.656 0.917,0.448 10 +B1 5.667,6.219 6.583,6.667 0.917,0.448 10 GND1 5.667,2.385 6.583,2.833 0.917,0.448 10 IG 1.667,0.5 2.583,0.948 0.917,0.448 10 1 1.667,1.083 2.583,1.531 0.917,0.448 10 2 5.667,1.219 6.583,1.667 0.917,0.448 10 CANL 5.667,0.635 6.583,1.083 0.917,0.448 10 CANH 5.24,0.365 6.156,0.813 0.917,0.448 10 9 5.198,0.948 6.115,1.396 0.917,0.448 10 10 5.24,5.938 6.156,6.385 0.917,0.448 10 7 5.25,4.104 6.167,4.552 0.917,0.448 10 3 5.24,2.938 6.156,3.385 0.917,0.448 10 4 5.229,2.115 6.146,2.563 0.917,0.448 10 1 5.125,6.198 6.042,6.646 0.917,0.448 10 G137 5.135,4.354 6.052,4.802 0.917,0.448 10 G137 5.125,3.198 6.042,3.646 0.917,0.448 10 G137 5.125,2.375 6.042,2.823 0.917,0.448 10 G139 5.135,1.198 6.052,1.646 0.917,0.448 10 G139 5.125,0.615 6.042,1.063 0.917,0.448 10 G139

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION ECU SUB-ASSEMBLY CAN BRANCH WIRE)
a.
E140414C06
1.469,0.417 1.969,0.698 0.5,0.281 2.083,1.469 2.25,2 2.25,2 2.5,2 true 1.938,1.469 1.833,2 1.833,2 1.667,2 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 2.552,1.917 3.167,2.115 0.615,0.198 10 CANL 1.24,1.927 1.854,2.125 0.615,0.198 10 CANH 1.542,0.469 2,0.667 0.458,0.198 10 G139
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the navigation ECU sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G139-9 (CANH) - G139-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NAVIGATION ECU SUB-ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277477C03
1.458,0.198 1.896,0.438 0.438,0.24 1.49,1.802 1.927,2.042 0.438,0.24 0.969,2.604 0.708,2.427 0.708,2.427 0.542,2.427 true 2.104,1.5 1.854,1.5 1.854,1.5 1.667,1.167 true 0.333,2.354 0.792,2.552 0.458,0.198 10 IG 2.146,1.417 2.688,1.646 0.542,0.229 10 GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 *a 1.51,0.25 1.969,0.448 0.458,0.198 10 G137 1.531,1.844 1.99,2.042 0.458,0.198 10 G139
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the navigation ECU sub-assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G139-1 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G137-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BATTERY)
a.
C277478C04
1.469,0.24 1.938,0.521 0.469,0.281 2.333,1.167 2.5,1.333 2.5,1.333 2.75,1.333 true 2.083,1.083 2.333,0.833 2.333,0.833 2.583,0.833 true 0.073,0.063 0.531,0.26 0.458,0.198 10 *a 1.542,0.302 2,0.5 0.458,0.198 10 G137 2.625,0.75 3.083,0.948 0.458,0.198 10 ACC1 2.792,1.25 3.25,1.448 0.458,0.198 10 +B1
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G137-4 (+B1) - Body ground Always 11 to 14 V
G137-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - ENGINE STOP AND START ECU)
4.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G137-4 (+B1) - G87-2 (BO1) Always Below 1 Ω
G137-3 (ACC1) - G87-3 (ACO) Always Below 1 Ω
G137-4 (+B1) - Body ground Always 10 kΩ or higher
G137-3 (ACC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR