When the back door cannot be opened, one of the following may be malfunctioning: 1) multiplex network door ECU, 2) back door lock assembly, 3) back door opener switch assembly, 4) main body ECU (multiplex network body ECU), or 5) certification ECU (smart key ECU assembly)*.
*: w/ Entry and Start System
For vehicles with an entry and start system:
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system.
The back door closer system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Check for DTCs.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC is not output |
| DTC B2250 is output |
| DTC B2251 is output |
DTC is not output
DTC B2250 is output
DTC B2251 is output
Check the power door lock basic function.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
The power door lock basic function can be operated normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the back door lock functions properly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Open | Back door condition signal | Permit or Prohibit | Permit: Back door unlocked
Prohibit: Back door locked |
- |
| Tester Display |
|---|
| Back Door Open |
The back door functions as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Check if the back door lock functions properly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock Status | Back door condition signal | Lock or Unlock | Lock: Back door locked
Unlock: Back door unlocked |
- |
| Tester Display |
|---|
| Door Lock Status |
The back door functions as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle types.
| Proceed to |
|---|
| w/ Entry and Start System |
| w/o Entry and Start System |
w/ Entry and Start System
w/o Entry and Start System
Check if the back door opener switch assembly functions properly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Back door control switch assembly signal | ON or OFF | ON: Back door opener switch assembly on
OFF: Back door opener switch assembly off |
- |
| Tester Display |
|---|
| Tr/B-Door Unlock SW |
The back door control switch assembly functions as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door lock assembly.
Inspect the back door lock assembly.
Click hereVehicle Interior>DOOR LOCK>BACK DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the U13 back door lock assembly connector.
Disconnect the U18 and U19 multiplex network door ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U13-1 (M+) - U19-10 (DC+) | Always | Below 1 Ω |
| U13-2 (M-) - U19-9 (DC-) | Always | Below 1 Ω |
| U13-3 (CTY) - U18-19 (FUL) | Always | Below 1 Ω |
| U13-5 (CLS) - U18-21 (HAF) | Always | Below 1 Ω |
| U13-6 (OPN) - U18-24 (POS) | Always | Below 1 Ω |
| U13-4 (E) - Body ground | Always | Below 1 Ω |
| U13-1 (M+) or U19-10 (DC+) - Body ground | Always | 10 kΩ or higher |
| U13-2 (M-) or U19-9 (DC-) - Body ground | Always | 10 kΩ or higher |
| U13-3 (CTY) or U18-19 (FUL) - Body ground | Always | 10 kΩ or higher |
| U13-5 (CLS) or U18-21 (HAF) - Body ground | Always | 10 kΩ or higher |
| U13-6 (OPN) or U18-24 (POS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the multiplex network door ECU with a new or normally functioning one.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the back door open operation.
| Proceed to |
|---|
| Back door can be opened |
| Back door cannot be opened |
Back door can be opened
Back door cannot be opened
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Remove the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL
Inspect the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the U7 back door opener switch assembly connector.
Disconnect the G83 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U7-3 (UL) - G83-27 (TSW5) | Always | Below 1 Ω |
| U7-2 (E) - Body ground | Always | Below 1 Ω |
| U7-3 (UL) or G83-27 (TSW5) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if the back door opener switch assembly functions properly.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR CLOSER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Open Handle SW | Back door control switch assembly signal | ON or OFF | ON: Back door opener switch assembly on
OFF: Back door opener switch assembly off |
- |
| Tester Display |
|---|
| Back Door Open Handle SW |
The back door control switch assembly functions as specified in the normal condition column.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CLOSER SWITCH>REMOVAL
Inspect the back door opener switch assembly.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR CLOSER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the U7 back door opener switch assembly connector.
Disconnect the G78 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| U7-3 (UL) - G78-23 (BDSU) | Always | Below 1 Ω |
| U7-2 (E) - Body ground | Always | Below 1 Ω |
| U7-3 (UL) or G78-23 (BDSU) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
NG