Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM
RM3090E _58 Vehicle Interior _008782 DOOR LOCK _0050260 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the main body ECU (multiplex network body ECU) sends an unlock warning switch signal and driver door courtesy light switch signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

for LHD


B281179E15
6.083,1.781 6.615,2.167 0.531,0.385 10 CAN 5.052,1.781 5.542,2.135 0.49,0.354 10 CAN 4.344,1.646 4.958,2.052 0.615,0.406 10 FLCY 4.344,0.604 4.896,0.917 0.552,0.313 10 KSW 2.104,0.49 2.458,0.865 0.354,0.375 10 1 2.125,1.51 2.698,2.021 0.573,0.51 10 1 1.302,0.49 1.594,0.813 0.292,0.323 10 2 0.854,3.365 2.771,3.677 1.917,0.313 10 : CAN Communication Line 0.667,2.021 2.771,2.656 2.104,0.635 10 Front Door Courtesy Light Switch Assembly LH (for Driver Door) 1,0.927 2.49,1.427 1.49,0.5 10 Unlock Warning Switch Assembly 4.313,2.813 5.49,3.615 1.177,0.802 10 Main Body ECU (Multiplex Network Body ECU) 5.906,2.781 7.125,3.396 1.219,0.615 10 Combination Meter Assembly 4,0.385 4.313,0.677 0.313,0.292 10 17 3.052,1.656 3.708,2.083 0.656,0.427 10 3E 3.052,1.438 3.594,1.958 0.542,0.521 10 40 4.031,1.427 4.604,2.052 0.573,0.625 10 2 2.938,2.479 4,3.292 1.063,0.813 10 Instrument Panel Junction Block Assembly 3.958,0.615 4.323,1.021 0.365,0.406 10 G78 4.021,1.646 4.313,1.823 0.292,0.177 10 A 1,0.76 1.344,1 0.344,0.24 10 G7 0.667,1.854 1.042,2.115 0.375,0.26 10 N6


for RHD


B319944E03
6.146,1.833 6.708,2.26 0.563,0.427 10 CAN 5.115,1.833 5.75,2.229 0.635,0.396 10 CAN 4.406,1.708 4.906,2.073 0.5,0.365 10 FRCY 4.406,0.677 5.104,1.125 0.698,0.448 10 KSW 2.177,0.531 3.021,1.042 0.844,0.51 10 1 2.167,1.583 2.51,1.896 0.344,0.313 10 1 1.333,0.542 1.948,1 0.615,0.458 10 2 0.927,3.302 3.094,3.635 2.167,0.333 10 : CAN Communication Line 0.74,2.094 2.896,2.74 2.156,0.646 10 Front Door Courtesy Light Switch Assembly RH (for Driver Door) 1.042,0.979 2.583,1.708 1.542,0.729 10 Unlock Warning Switch Assembly 4.365,2.688 5.573,3.479 1.208,0.792 10 Main Body ECU (Multiplex Network Body ECU) 5.948,2.667 7.135,3.354 1.188,0.688 10 Combination Meter Assembly 4.031,1.479 4.396,1.802 0.365,0.323 10 19 4.01,1.708 4.458,2.115 0.448,0.406 10 G78 4.042,0.458 4.583,0.854 0.542,0.396 10 17 4,0.677 4.677,1.146 0.677,0.469 10 G78 1.042,0.833 1.573,1.177 0.531,0.344 10 G7 0.729,1.917 1.219,2.25 0.49,0.333 10 M4


CAUTION / NOTICE / HINT

NOTICE:
·

The key reminder warning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the key reminder warning system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.



PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (SEAT BELT WARNING BUZZER OPERATION)
a.

Check seat belt warning system operation.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM(w/o Occupant Classification System)>OPERATION CHECK

HINT:

The key reminder warning system sounds the buzzer built into the combination meter assembly as a key reminder warning. This buzzer is also used for the seat belt warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the seat belt is not fastened.



Result:
Proceed to
Combination meter buzzer sounds
Combination meter buzzer not sounds



Combination meter buzzer sounds

2.READ VALUE USING GTS (FR Door Courtesy SW, FL Door Courtesy SW)

Combination meter buzzer not sounds

2.READ VALUE USING GTS (FR Door Courtesy SW, FL Door Courtesy SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch RH signal ON or OFF ON: Front door RH open
OFF: Front door RH closed
*1
FL Door Courtesy SW Front door courtesy light switch LH signal ON or OFF ON: Front door LH open
OFF: Front door LH closed
*2

*1: for RHD

*2: for LHD


Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

The GTS indicates ON or OFF according to the driver door condition shown in the table.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (Key Unlock Warning SW)

NG

8.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for Driver Door)
3.READ VALUE USING GTS (Key Unlock Warning SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal ON or OFF ON: Key in ignition key cylinder
OFF: No key in ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

The GTS indicates ON or OFF according to whether the key is in the ignition key cylinder.



Result:
Proceed to
OK
NG



OK

4.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
4.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new one.



b.

Check the key reminder buzzer operation.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK


Result:
Proceed to
Key reminder buzzer sounds
Key reminder buzzer not sounds



Key reminder buzzer sounds

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

Key reminder buzzer not sounds

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the G7 unlock warning switch assembly connector.


b.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-1 - G78-17 (KSW) Always Below 1 Ω
G7-2 - Body ground Always Below 1 Ω
G7-1 - Body ground Always 10 kΩ or higher
G78-17 (KSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Temporarily replace the main body ECU (multiplex network body ECU) with a new one.



b.

Check the key reminder buzzer operation.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK


Result:
Proceed to
Key reminder buzzer sounds
Key reminder buzzer not sounds



Key reminder buzzer sounds

END (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] WAS DEFECTIVE)

Key reminder buzzer not sounds

8.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for Driver Door)
a.

Remove the front door courtesy light switch assembly (for driver door).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly (for driver door).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK (for LHD)
OK (for RHD)
NG



OK (for LHD)

9.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

OK (for RHD)

11.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for Driver Door)

9.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the N6 front door courtesy light switch assembly LH connector.


b.

Disconnect the 3E instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N6-1 - 3E-40 Always Below 1 Ω
N6-1 - Body ground Always 10 kΩ or higher
3E-40 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

B281983C16
1.917,1 2.333,1.25 0.417,0.25 5.5,0.833 5.917,1.083 0.417,0.25 0.75,2.167 0.479,2.167 0.479,2.167 0.479,1.75 false 0.229,0.156 0.542,0.354 0.313,0.198 10 *a 5.635,0.875 5.948,1.073 0.313,0.198 10 3E 2.083,1.052 2.396,1.25 0.313,0.198 10 A 0.833,2.083 1.448,2.281 0.615,0.198 10 FLCY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3E-40 - A-2 (FLCY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the M4 front door courtesy light switch assembly RH connector.


b.

Disconnect the G78 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-1 - G78-19 (FRCY) Always Below 1 Ω
M4-1 - Body ground Always 10 kΩ or higher
G78-19 (FRCY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR