Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2012.12–2015.04
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051011 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly)*1 or deceleration sensor*2.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1585 Acceleration Sensor Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The ignition switch is ON.

2.

The output value of the yaw rate and acceleration sensor*1 or deceleration sensor*2 remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

3.

0.5 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

The power source voltage to the yaw rate and acceleration sensor*1 or deceleration sensor*2 remains at 4.4 V or less, or 5.6 V or higher for at least 1.2 seconds.

3.

0.5 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

No signal from the yaw rate and acceleration sensor*1 or deceleration sensor*2 is detected 7 times or more.

3.

0.5 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G.

3.

0.5 seconds

4.

1 trip detection logic


1.

The ignition switch is ON.

2.

A yaw rate and acceleration sensor*1 or deceleration sensor*2 power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more.

3.

0.5 seconds

4.

1 trip detection logic


·

Yaw rate and acceleration sensor (Airbag sensor assembly)*1

·

Deceleration sensor*2

·

Skid control ECU (Brake actuator assembly)

·

CAN communication system


- DTC stored

*1: w/ VSC

*2: w/o VSC

WIRING DIAGRAM

C277061E01
1.26,0.583 1.719,0.781 0.458,0.198 10 GL1 1.115,0.948 1.667,1.198 0.552,0.25 10 GGND 1.208,1.313 1.76,1.563 0.552,0.25 10 VGS 1.656,0.708 1.917,0.927 0.26,0.219 10 1 1.667,1.063 1.927,1.281 0.26,0.219 10 2 1.656,1.417 1.917,1.635 0.26,0.219 10 3 2.802,0.708 3.063,0.927 0.26,0.219 10 3 2.74,1.063 3,1.281 0.26,0.219 10 15 2.719,1.427 2.979,1.646 0.26,0.219 10 26 3.031,0.604 3.49,0.802 0.458,0.198 10 GL1*2 3.021,0.938 3.573,1.188 0.552,0.25 10 GGND*2 3.021,1.302 3.573,1.552 0.552,0.25 10 VGS*2 5.813,3.74 6.365,3.99 0.552,0.25 10 ECM 0.292,1.75 0.844,2 0.552,0.25 10 N5*2 0.281,1.958 1.865,2.271 1.583,0.313 10 Deceleration Sensor*2 2.51,1.76 3.063,2.01 0.552,0.25 10 A63*2 2.479,1.979 4.604,2.406 2.125,0.427 10 Skid Control ECU (Brake Actuator Assembly) 1.177,3.74 3.354,4.104 2.177,0.365 10 Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly)*1 0.458,5.323 2.271,5.563 1.813,0.24 10 : CAN Communication Line 0.146,4.625 0.979,4.844 0.833,0.219 10 *1: w/ VSC 0.146,4.969 0.979,5.188 0.833,0.219 10 *2: w/o VSC

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

If a CAN communication DTC is output, perform troubleshooting for that DTC first.


PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs of the CAN communication system.


Result:
Proceed to
DTCs are not output
DTCs are output




DTCs are not output

2.READ VALUE USING GTS (G SENSOR)

DTCs are output

2.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of deceleration sensor min.: 0 V
max.: 79.998 V
Displays converted voltage of deceleration sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

e.

In accordance with the display on the GTS, read the Data List.

Result:
Result Proceed to
Data displayed is as specified under Normal Condition (w/ VSC) A
Data displayed is as specified under Normal Condition (w/o VSC) B
Data displayed is not as specified under Normal Condition (w/ VSC) C
Data displayed is not as specified under Normal Condition (w/o VSC) D




A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

3.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

C

4.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

D

5.CHECK HARNESS AND CONNECTOR (DECELERATION SENSOR - SKID CONTROL ECU)
3.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
a.

Replace the skid control ECU (brake actuator assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.REPLACE YAW RATE AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)
a.

Replace the yaw rate and acceleration sensor (airbag sensor assembly).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK HARNESS AND CONNECTOR (DECELERATION SENSOR - SKID CONTROL ECU)
a.

Disconnect the N5 deceleration sensor connector.


b.

Disconnect the A63 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N5-1 (GL1) - A63-3 (GL1) Always Below 1 Ω
N5-2 (GGND) - A63-15 (GGND) Always Below 1 Ω
N5-3 (VGS) - A63-26 (VGS) Always Below 1 Ω
N5-1 (GL1) or A63-3 (GL1) - Body ground Always 10 kΩ or higher
N5-2 (GGND) or A63-15 (GGND) - Body ground Always 10 kΩ or higher
N5-3 (VGS) or A63-26 (VGS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT DECELERATION SENSOR (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT DECELERATION SENSOR (POWER SOURCE)
a.
C199166C02
0.479,1.031 0.906,1.323 0.427,0.292 1.906,1.229 2.177,1.813 true 0.115,0.104 0.427,0.302 0.313,0.198 10 *a 2.063,1.865 2.479,2.094 0.417,0.229 10 VGS 0.635,1.094 0.948,1.292 0.313,0.198 10 N5
*a Front view of wire harness connector
(to Deceleration Sensor)


Disconnect the deceleration sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N5-3 (VGS) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

7.INSPECT DECELERATION SENSOR (GL1 VOLTAGE)

NG

3.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
7.INSPECT DECELERATION SENSOR (GL1 VOLTAGE)
a.
C277071C01
1.698,1.74 1.698,1.177 true 1.146,1.729 1.469,1.177 true 2.281,1.719 1.948,1.177 true 0.188,0.146 0.5,0.344 0.313,0.198 10 *a 0.927,1.813 1.375,2.021 0.448,0.208 10 VGS 1.49,1.813 2.031,2.042 0.542,0.229 10 GGND 2.25,1.813 2.688,2.063 0.438,0.25 10 GL1
*a Component without harness connected
(Deceleration Sensor)


Remove the deceleration sensor.


b.

Connect 3 dry cell batteries of 1.5 V in series.


c.

Connect the positive (+) lead of the batteries to terminal 3 (VGS) and the negative (-) lead to terminal 2 (GGND) to apply a voltage of 4.5 V.

NOTICE:
·

Do not apply 6 V or higher to terminals 3 (VGS) and 2 (GGND).

·

If the sensor is dropped, replace it with a new one.




d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (GL1) - 2 (GGND)
·

4.5 V applied to terminals 3 (VGS) and 2 (GGND)

·

Sensor not tilted


Approx. 2.5 V
1 (GL1) - 2 (GGND)
·

4.5 V applied to terminals 3 (VGS) and 2 (GGND)

·

Sensor tilted back and forth


Changes between approx. 0.5 V and 4.5 V


HINT:

If the sensor is tilted too much, it may output the wrong value.



Result:
Proceed to
OK
NG



OK

3.REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

8.REPLACE DECELERATION SENSOR
8.REPLACE DECELERATION SENSOR

NEXT