Home › Drivetrain › K111F MULTIDRIVE / CVT › FRONT DIFFERENTIAL OIL SEAL(for RH Side)
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051017 FRONT DIFFERENTIAL OIL SEAL(for RH Side) A

K111F MULTIDRIVE / CVT  FRONT DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


PROCEDURE

Hide 30400 1.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Hide 36100 2.REMOVE TRANSFER ASSEMBLY

Hide 30400B 3.REMOVE CVT TYPE T OIL SEAL (OUTER)

C279200C01
2.323,1.198 1.365,0.417 1.365,0.417 0.927,0.417 false 0.74,0.333 1.052,0.531 0.313,0.198 10 false *a
*a Protective Tape


a.

Using a screwdriver with protective tape wound around the tip, pry out the CVT type T oil seal.

NOTICE:

Be careful not to damage the housing.



Hide 30400B 4.REMOVE CVT TYPE T OIL SEAL (INNER)

C103312E01
2.932,1.991 3.253,2.17 0.32,0.179 10 SST 0.452,0.69 0.773,0.868 0.32,0.179 10 SST 1.288,1.109 0.902,0.773 0.902,0.773 0.818,0.773 false 2.633,2.817 2.809,2.074 2.809,2.074 2.906,2.074 false

a.

Using SST, tap out the CVT type T oil seal oil seal.

SST
09308-00010  

NOTICE:

Be careful not to damage the housing.



Hide 30400B 5.INSTALL CVT TYPE T OIL SEAL (INNER)

a.
C279201E01
1.573,1.792 1.573,1.031 false 1.573,1.594 1.229,1.604 1.229,1.604 1.229,1.354 false 2.875,0.76 2.875,0.219 2.875,0.219 2.729,0.219 false 3.188,0.948 3.198,0.5 3.198,0.5 2.875,0.5 false 1.458,1.844 1.917,2.042 0.458,0.198 10 SST 2.427,0.135 2.885,0.333 0.458,0.198 10 SST

Using SST and a hammer, tap in a new CVT type T oil seal.

SST
09950-60010  (09951-00390)
09950-70010  (09951-07200)

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Do not damage the lip of the CVT type T oil seal.



b.

Coat the lip of the CVT type T oil seal with MP grease.


Hide 30400B 6.INSTALL CVT TYPE T OIL SEAL (OUTER)

a.

Coat the lip of a new CVT type T oil seal with MP grease.


b.
C279202E01
0.771,1.865 1.281,1.854 1.281,1.854 1.365,1.302 false 0.458,1.792 0.917,1.99 0.458,0.198 10 SST

Using SST and a hammer, tap in the CVT type T oil seal.

SST
09316-60011  (09316-00011)

Standard depth:

4.5 to 5.5 (0.178 to 0.216 in.)


NOTICE:

Do not damage the lip of the CVT type T oil seal.



Hide 36100 7.INSTALL TRANSFER ASSEMBLY

Hide 30400 8.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY