Home › Drivetrain › K111F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › 2012.12–2015.10
RM3090E _52 Drivetrain _009408 K111F MULTIDRIVE / CVT _0051014 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K111F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000A 1.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 30400E 2.INSTALL CVT OIL PUMP TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands, and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.


b.

Temporarily attach the CVT oil pump type T oil seal by pressing it onto the installation surface of the oil pump housing manually.


c.
C208789C02
1.802,1.792 1.802,2.469 false 1.698,2.5 2.125,2.74 0.427,0.24 10 false SST 0.927,2.458 1.302,2.802 0.375,0.344 10 false *a
*a 0 to 0.5 mm (0 to 0.0196 in.)


Clean the oil seal contact section of SST and the area around it.


d.

Using SST, drive the CVT oil pump type T oil seal in evenly, as far as the side surface of the oil pump housing.

SST
09309-36010  

NOTICE:
·

Drive the oil seal in gradually, while visually checking the parallelism.

·

After the installation, confirm that the oil seal has been driven in as far as the side surface of the oil pump housing.

·

Wipe off any grease that has oozed out with your hand.



HINT:

The oil seal should be driven in between 0 and 0.5 mm (0 and 0.0196 in.) as measured from the side surface of the oil pump housing.



Hide 32000A 3.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C169590C02
2.771,0.198 1.729,0.198 false 2.792,1.031 1.75,1.031 false 2.802,0.104 3.083,0.365 0.281,0.26 10 *a 2.833,0.958 3.125,1.24 0.292,0.281 10 *b
*a Matchmark
*b Groove


Turn the front oil pump drive gear so that the groove is at the top and put a matchmark on the housing.


b.
C169591C03
1.448,1.917 1.531,1.917 1.531,1.917 1.719,1.635 false 1.927,0.094 1.854,0.094 1.854,0.094 1.74,0.281 false 1.969,0.021 2.365,0.271 0.396,0.25 10 *b 1.26,1.833 1.542,2.063 0.281,0.229 10 *a
*a Matchmark
*b Key


Put a matchmark on the torque converter so that the position of its key is clearly indicated.


c.
C203359C02
1.208,0.417 1.573,0.271 1.573,0.271 1.677,0.271 false 1.198,0.698 1.583,0.26 false 1.688,0.177 1.958,0.417 0.271,0.24 10 *a
*a Matchmark


Align the matchmark on the housing with the one on the torque converter and mesh the splines of the input shaft with the turbine runner splines.

NOTICE:

Install the torque converter horizontally to the input shaft.



d.
C203360C02
1.198,0.396 1.344,0.115 1.344,0.115 1.448,0.115 false 1.198,1.583 1.021,2.01 1.021,2.01 0.885,2.021 false 2.531,0.844 1.979,1.875 1.979,1.875 1.875,1.875 false 2.521,1.188 1.979,1.875 false 0.708,1.948 0.948,2.156 0.24,0.208 10 *a 1.5,0.031 1.729,0.26 0.229,0.229 10 *a 1.667,1.781 1.854,1.979 0.188,0.198 10 *1
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter and mesh the splines of the stator shaft with the stator splines.

HINT:

Rotate the torque converter approximately 180°.


NOTICE:
·

Do not damage the oil seal.

·

Install the torque converter horizontally to the input shaft.




e.
C203361C02
1.188,0.396 1.531,0.167 1.531,0.167 1.625,0.167 false 1.208,0.625 1.531,0.167 false 1.802,1.896 2.531,0.854 false 2.521,1.198 1.802,1.896 1.802,1.896 1.698,1.896 false 1.656,0.073 1.958,0.333 0.302,0.26 10 *a 1.542,1.833 1.854,2.094 0.313,0.26 10 *1
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter again, align the matchmark on the housing with the one on the torque converter and insert the key of the torque converter into the groove of the oil pump drive gear.

NOTICE:
·

Do not push the torque converter excessively when rotating it.

·

Do not damage the oil seal.

·

Install the torque converter horizontally to the input shaft.




f.

Clean the torque converter set bolt holes.


g.
C279069C02
0.74,1.188 0.615,0.375 0.615,0.375 0.417,0.375 false 1.031,3.063 1.031,2.542 false 0.25,0.302 0.594,0.625 0.344,0.323 10 *1 1,3.104 1.302,3.365 0.302,0.26 10 *2 3,0.823 3.208,1.021 0.208,0.198 10 *1 2.979,1.615 3.292,1.813 0.313,0.198 10 *2 2.229,0.469 2.385,0.667 0.156,0.198 10 A
*1 Engine Surface
*2 Drive Plate Surface


Using a vernier caliper and straightedge, measure dimension "A" between the transaxle contact surface of the engine*1 and the torque converter assembly contact surface of the drive plate*2. (#)


h.
C194183E01
2.501,0.242 2.636,0.398 0.135,0.156 10 B

Using a vernier caliper and straightedge, measure dimension "B" shown in the illustration and check that dimension "B" is more than dimension "A" (which was measured in step (#)).

Standard:

A + 1 mm (0.0394 in.) or more


NOTICE:

Subtract the thickness of the straightedge from the measured value to gain dimension "B".



Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the 4 wire harness clamp brackets to the continuously variable transaxle assembly with the 4 bolts.

Torque:
for Bolt A : 7.7 N*m (79 kgf*cm, 68 in.*lbf)
for Bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)

C283588E01
2,0.875 2.156,1.073 0.156,0.198 10 false B 1.052,1.74 1.208,1.938 0.156,0.198 10 false A 4.823,1.125 4.979,1.323 0.156,0.198 10 false A 5.688,2.51 5.844,2.708 0.156,0.198 10 false A


Hide 33823 5.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C279762

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 36100A 6.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT


a.

Clean the bolt holes.


b.

Apply adhesive 1324 to 2 or 3 threads on one half of a new transfer and transaxle setting stud bolt A as shown in the illustration.

C291118C01
4.417,0.177 4.729,0.375 0.313,0.198 10 false A 5.802,0.396 5.958,0.594 0.156,0.198 10 false B 2.365,0.458 2.521,0.656 0.156,0.198 10 false A 2.344,1.24 2.5,1.438 0.156,0.198 10 false B 0.583,1.24 0.896,1.438 0.313,0.198 10 false *a 0.604,1.49 0.917,1.688 0.313,0.198 10 false *b
*a Adhesive 1324 *b Sealant


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:
·

Do not apply adhesive 1324 to the ends of the stud bolt.

·

Install the stud bolt immediately after applying adhesive to prevent the adherence of foreign matter.



NOTICE:

Install the sealed side of the stud bolt to the transaxle assembly.



c.

Install the 2 new transfer and transaxle setting stud bolts to the transaxle case positions shown in the illustration.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

NOTICE:

Install the stud bolt so that the side that has sealant and adhesive is facing the automatic transaxle assembly.


HINT:

Stud bolt length:

Stud bolt A: 69 mm (2.72 in.)

Stud bolt B: 47 mm (1.85 in.)



Hide 36100 7.INSTALL TRANSFER ASSEMBLY

Hide 30400 8.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

C279775C01
1.594,1.125 2.49,0.469 2.49,0.469 2.708,0.469 false 2.771,0.396 3.219,0.688 0.448,0.292 10 *1 1.146,0.958 1.5,1.271 0.354,0.313 10 *2
*1 Torque Converter Assembly Centerpiece
*2 Crankshaft


a.

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C279070E01
1.188,2.208 1.344,2.406 0.156,0.198 10 A 2.354,2.219 2.51,2.417 0.156,0.198 10 A 2.615,2.5 2.771,2.698 0.156,0.198 10 A 0.792,2.969 0.948,3.167 0.156,0.198 10 B 1.031,4.042 1.188,4.24 0.156,0.198 10 B 1.323,4.333 1.479,4.531 0.156,0.198 10 B 1.854,4.427 2.01,4.625 0.156,0.198 10 B 2.448,4.271 2.604,4.469 0.156,0.198 10 B

Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.


c.

Maintain the engine and continuously variable transaxle assembly in a horizontal position, align the knock pins with each hole on the continuously variable transaxle assembly and install the continuously variable transaxle assembly with the 8 bolts shown in the illustration.

Torque:
for bolt A : 38 N*m (387 kgf*cm, 28 ft.*lbf)
for bolt B : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:

Bolt A: Install from the continuously variable transaxle assembly side.

Bolt B: Install from the engine assembly side.


CAUTION:

Make sure that the torque converter rotates.



Hide 32101A 9.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

P000601C15
1.854,1.427 1.854,1.875 1.854,1.875 1.604,1.885 true 1.406,1.823 1.656,2.063 0.25,0.24 10 *a
*a Adhesive


a.

Apply a few drops of adhesive to 2 or 3 threads at the tips of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324,

Three Bond 1324 or equivalent



b.
C279071

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

Install the black bolt first, and then the remaining 5 silver bolts.



c.

Install the flywheel housing under cover.


Hide 10.INSTALL ENGINE WIRE

a.

for Front Side:

Attach the 3 wire harness clamps and connect the 3 revolution sensor connectors, park/neutral position sensor connector and transmission wire connector to the continuously variable transaxle assembly.


b.

for Rear Side:

Attach the 2 wire harness clamps and connect the oil pressure sensor connector to the continuously variable transaxle assembly.

C279761C02
0.302,0.115 0.667,0.406 0.365,0.292 10 *a 3.802,0.115 4.208,0.406 0.406,0.292 10 *b
*a for Front Side *b for Rear Side



Hide 11.INSTALL GROUND CABLE

a.

Install the ground cable to the continuously variable transaxle assembly with the bolt and attach the clamp.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 12321A 12.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Install the rear engine mounting bracket to the continuously variable transaxle assembly with the 3 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12311A 13.INSTALL FRONT ENGINE MOUNTING BRACKET

a.

Install the front engine mounting bracket to the continuously variable transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12325A 14.INSTALL ENGINE MOUNTING BRACKET LH

a.

Install the engine mounting bracket LH to the continuously variable transaxle assembly with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 16282 16.CONNECT WATER BY-PASS HOSE

C279764C01
0.417,0.719 1.26,0.698 false 0.438,1.542 0.823,2 0.823,2 1.042,2 false 0.219,0.604 0.594,0.927 0.375,0.323 10 *a 1.094,1.896 1.49,2.177 0.396,0.281 10 *a
*a Yellow Paint Mark


a.

Connect the 2 water by-pass hoses to the oil cooler, and slide the clamp to secure it.

NOTICE:

Make sure the pinching portion of each clip is facing the directions shown in the illustration and the paint marks are aligned as shown in the illustration.