Home › Power Source / Network › 2AD-FTV BATTERY / CHARGING › CHARGING SYSTEM
RM3090E _57 Power Source / Network _008780 2AD-FTV BATTERY / CHARGING _0051075 CHARGING SYSTEM C

2AD-FTV BATTERY / CHARGING  CHARGING SYSTEM  P1550  Battery Current Sensor Circuit  P1551  Battery Current Sensor Circuit Low  P1552  Battery Current Sensor Circuit High  


DESCRIPTION

The battery current sensor assembly detects the battery charge and discharge current amount.

The battery current sensor assembly changes this information into a voltage signal and outputs it to the ECM.

Based on this signal, the ECM sends power generation voltage commands to the generator.

A194388E05
0.469,2.802 1.083,3 0.615,0.198 10 -100 1.125,2.792 1.583,2.99 0.458,0.198 10 -50 1.792,2.802 2.25,3 0.458,0.198 10 0 2.333,2.802 2.792,3 0.458,0.198 10 50 2.885,2.802 3.406,3 0.521,0.198 10 100 (A) 1.635,3.052 2.219,3.25 0.583,0.198 10 Current 0.24,2.656 0.854,2.854 0.615,0.198 10 0 0.125,2.469 0.74,2.667 0.615,0.198 10 0.5 0.24,2.302 0.854,2.5 0.615,0.198 10 1 0.135,2.104 0.75,2.302 0.615,0.198 10 1.5 0.24,1.927 0.427,2.177 0.188,0.25 10 2 0.135,1.75 0.75,1.948 0.615,0.198 10 2.5 0.24,1.583 0.438,1.75 0.198,0.167 10 3 0.135,1.406 0.75,1.604 0.615,0.198 10 3.5 0.25,1.229 0.448,1.427 0.198,0.198 10 4 0.135,1.042 0.75,1.24 0.615,0.198 10 4.5 0.25,0.865 0.448,1.063 0.198,0.198 10 5 0.135,0.583 0.333,0.781 0.198,0.198 10 (V) 0.094,0.094 1.76,0.427 1.667,0.333 10 Sensor Output Voltage

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1550 Battery Current Sensor Circuit Difference between the maximum and minimum current values of the battery current sensor is less than 1 A for 10 seconds or more
(1 trip detection logic)
·

Battery current sensor assembly

·

ECM

·

Wire harness or connector


Does not come on DTC stored
P1551 Battery Current Sensor Circuit Low Battery current sensor output value is abnormally low for 0.5 seconds or more with the ignition switch ON
(1 trip detection logic)
·

Battery current sensor assembly

·

ECM

·

Wire harness or connector


Does not come on DTC stored
P1552 Battery Current Sensor Circuit High Battery current sensor output value is abnormally high for 0.5 seconds or more with the ignition switch ON
(1 trip detection logic)
·

Battery current sensor assembly

·

ECM

·

Wire harness or connector


Does not come on DTC stored

WIRING DIAGRAM

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1550, P1551 OR P1552)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Proceed to
DTC P1550, P1551 or P1552 is output
DTC P1550, P1551 or P1552 and other DTCs are output


HINT:

If any DTCs other than P1550, P1551 or P1552 are output, troubleshoot those DTCs first.




DTC P1550, P1551 or P1552 is output

2.READ VALUE USING GTS (BATTERY CURRENT)

DTC P1550, P1551 or P1552 and other DTCs are output

2.READ VALUE USING GTS (BATTERY CURRENT)
a.

Turn all of the electrical systems (headlights, blower motor, rear defogger, etc.) off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Battery Current.

Powertrain > Engine > Data List
Tester Display
Battery Current
50003 61 476
Result:
Result Proceed to
Battery current is fixed at 0 A, or fluctuates by 1 A or less between -100 and 100 A A
Battery current fluctuates between -20 and 0 A B




A

3.INSPECT BATTERY CURRENT SENSOR ASSEMBLY

B

3.INSPECT BATTERY CURRENT SENSOR ASSEMBLY
a.

Inspect the battery current sensor assembly.

Click herePower Source / Network>2AD-FTV BATTERY / CHARGING>BATTERY CURRENT SENSOR>INSPECTION

Result:
Result
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR ASSEMBLY - ECM)
a.

Disconnect the B76 ECM connector.


b.

Disconnect the B72 battery current sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
B76-77 (EIB) - B72-4 (E2) Always Below 1 Ω
B76-75 (VCIB) - B72-2 (VC5) Always Below 1 Ω
B76-116 (IB) - B72-3 (IB) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B76-77 (EIB) or B72-4 (E2) - Body ground Always 10 kΩ or higher
B76-75 (VCIB) or B72-2 (VC5) - Body ground Always 10 kΩ or higher
B76-116 (IB) or B72-3 (IB) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR