Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A209140E40
2.563,4.573 2.844,4.271 2.844,4.271 3.615,4.271 false 3.177,4.813 3.323,5.042 3.323,5.042 3.854,5.042 false 4.771,0.813 6.438,1.021 1.667,0.208 10 Camshaft Position Sensor 4.74,1.323 6.469,1.479 1.729,0.156 10 Crankshaft Position Sensor 0.073,0.01 0.948,0.208 0.875,0.198 10 VVT System: 2.333,1.958 3.615,2.135 1.281,0.177 10 Target Valve Timing 2.333,1.292 3.615,1.469 1.281,0.177 10 Actual Valve Timing 2.688,2.698 3.406,2.875 0.719,0.177 10 Correction 2.823,3.208 3.229,3.385 0.406,0.177 10 ECM 1.604,3.75 4.49,3.938 2.885,0.188 10 Camshaft Timing Oil Control Valve Assembly 0.167,2.688 0.865,2.865 0.698,0.177 10 Duty-cycle 4.531,1.833 6.76,2.052 2.229,0.219 10 Mass Air Flow Meter Sub-assembly 4.458,2.854 6.76,3.052 2.302,0.198 10 Engine Coolant Temperature Sensor 4.844,2.344 6.375,2.51 1.531,0.167 10 Throttle Position Sensor 4.885,3.365 6.323,3.542 1.438,0.177 10 Vehicle Speed Sensor 0.313,4.271 1.677,4.479 1.365,0.208 10 Engine Oil Pressure 3.667,4.219 7.063,4.406 3.396,0.188 10 VVT Controller (Camshaft Timing Gear Assembly) 3.885,4.948 4.99,5.135 1.104,0.188 10 Intake Camshaft

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 Camshaft Position "A" Actuator Circuit (Bank 1) Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly (for intake camshaft) circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the ignition switch is ON or the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Turn the ignition switch to ON and wait for 5 seconds or more.


WIRING DIAGRAM

A255118E36
0.604,1.865 3.406,2.24 2.802,0.375 10 Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) 0.271,1.865 0.563,2.01 0.292,0.146 10 B21 1.594,0.802 1.698,0.948 0.104,0.146 10 1 1.594,1.438 1.698,1.583 0.104,0.146 10 2 4.865,0.802 5.073,0.948 0.208,0.146 10 74 4.865,1.438 5.063,1.583 0.198,0.146 10 75 5.135,1.448 5.542,1.594 0.406,0.146 10 OC1- 5.135,0.813 5.542,0.958 0.406,0.146 10 OC1+ 5.656,2.229 5.99,2.375 0.333,0.146 10 ECM 5.323,2.229 5.615,2.375 0.292,0.146 10 B77

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0010 is output, check the VVT system (for intake camshaft) circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT (DTC P0010)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and wait 5 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0010 is output A
DTC is not output B




A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake camshaft).

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B21-1 - B77-74 (OC1+) Always Below 1 Ω
B21-2 - B77-75 (OC1-) Always Below 1 Ω
B21-1 or B77-74 (OC1+) - Body ground Always 10 kΩ or higher
B21-2 or B77-75 (OC1-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR