Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0051076 SFI SYSTEM(w/o Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

A290292
3.167,0.333 3.479,0.49 0.313,0.156 10 *1 5,0.344 5.313,0.5 0.313,0.156 10 *2
*1 Intake Air Control Valve Open *2 Intake Air Control Valve Closed


This circuit opens and closes the Intake Air Control Valve (IACV) in response to changes in the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0660 Intake Manifold Tuning Valve Control Circuit / Open (Bank 1) The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
·

The voltage of terminal ACIS of the ECM is low when the vacuum switching valve assembly (for acoustic control induction system) is off.

·

The engine has been started.


·

Open or short in vacuum switching valve (for acoustic control induction system) circuit

·

Vacuum switching valve assembly (for acoustic control induction system)

·

EFI-MAIN NO. 1 relay

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A300176
0.51,2.042 1.583,2.24 1.073,0.198 10 false FL MAIN 0.615,3.146 1.688,3.344 1.073,0.198 10 false Battery 0.563,1.125 1.521,1.281 0.958,0.156 10 false EFI-MAIN NO.1 1.698,1.76 2.698,1.917 1,0.156 10 false EFI-MAIN NO.1 2.927,1.135 3.615,1.396 0.688,0.26 10 false EFI NO.1 3.656,1.281 4.344,1.542 0.688,0.26 10 false B44 3.646,1.458 5.51,2.01 1.865,0.552 10 false Vacuum Switching Valve (for Acoustic Control Induction System) 5.698,0.833 6.385,1.094 0.688,0.26 10 false ACIS 5.698,2.313 6.385,2.573 0.688,0.26 10 false MREL 5.698,3.083 6.385,3.344 0.688,0.26 10 false E1 5.365,0.979 6.052,1.24 0.688,0.26 10 false B77 5.365,3.094 6.052,3.354 0.688,0.26 10 false B77 5.365,2.458 6.052,2.719 0.688,0.26 10 false A62 5.406,0.781 6.094,1.042 0.688,0.26 10 false 69 5.406,2.26 6.094,2.521 0.688,0.26 10 false 46 5.406,2.906 6.094,3.167 0.688,0.26 10 false 16 5.01,0.854 5.698,1.115 0.688,0.26 10 false 1 2.458,1.344 3.146,1.604 0.688,0.26 10 false 1 3.906,0.854 4.594,1.115 0.688,0.26 10 false 2 1.76,1.354 2.448,1.615 0.688,0.26 10 false 2 2.469,0.854 3.156,1.115 0.688,0.26 10 false 3 1.76,0.844 2.448,1.104 0.688,0.26 10 false 5 6.021,3.74 6.385,3.927 0.365,0.188 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVE THE VSV FOR INTAKE CONTROL)
a.
A204525
0.405,0.02 1.096,0.198 0.691,0.178 10 *a 2.044,0.02 2.796,0.213 0.752,0.193 10 *b 0.766,0.595 0.96,0.764 0.194,0.169 10 *c 0.87,1.792 1.076,1.96 0.206,0.168 10 *2 0.119,1.649 0.298,1.824 0.179,0.175 10 *1 2.211,0.657 2.407,0.829 0.196,0.172 10 *c 0.485,1.461 0.317,1.645 false 0.686,1.35 0.941,1.784 false 2.342,1.815 2.548,1.983 0.206,0.168 10 *2 1.591,1.672 1.77,1.847 0.179,0.175 10 *1 1.957,1.484 1.79,1.668 false 2.159,1.373 2.414,1.807 false
*1 Port F
*2 Port E
*a ON
*b OFF
*c Air


Disconnect the vacuum hose from port F on the vacuum switching valve assembly (for acoustic control induction system).


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Intake Control
50004 234 3

f.

Operate the vacuum switching valve assembly (for acoustic control induction system) check the air flow.

Standard:
Activate the VSV for Intake Control Specified Condition
ON Air from port E flows out through port F
OFF Air from port E flows out through air filter


Result:
Result Proceed to
Abnormal A
Normal B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



Result:
Proceed to
A
B



A

2.CHECK VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)

B

2.CHECK VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)
a.

Inspect the vacuum switching valve assembly (for acoustic control induction system).

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>VACUUM SWITCHING VALVE(for ACIS)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))

NG

REPLACE VACUUM SWITCHING VALVE ASSEMBLY (FOR ACOUSTIC CONTROL INDUCTION SYSTEM)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))
a.
A194112C29
0.521,2.156 0.938,2.427 0.417,0.271 0.292,0.385 0.5,0.563 0.208,0.177 10 *a 0.604,2.208 0.885,2.385 0.281,0.177 10 B44
*a Front view of wire harness connector
(to Vacuum Switching Valve Assembly (for Acoustic Control Induction System))


Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B44-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))
4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM) - ECM)
a.

Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B44-1 - B77-69 (ACIS) Always Below 1 Ω
B44-1 or B77-69 (ACIS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - VACUUM SWITCHING VALVE (FOR ACOUSTIC CONTROL INDUCTION SYSTEM))
a.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


b.

Disconnect the vacuum switching valve assembly (for acoustic control induction system) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI-MAIN NO. 1 relay terminal 3 - B44-2 Always Below 1 Ω
EFI-MAIN NO. 1 relay terminal 3 or B44-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE EFI-MAIN NO. 1

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR