Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048750 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by blinking the ABS warning light.

WIRING DIAGRAM

C243297
0.5,2.177 0.948,2.417 0.448,0.24 10 false ECM 0.5,2.021 1.479,2.281 0.979,0.26 10 false A62 1.094,1.542 1.323,1.698 0.229,0.156 10 false TC 5.333,1.49 6.865,1.979 1.531,0.49 10 false Skid Control ECU (Brake Actuator Assembly) 5.396,2.563 5.583,2.708 0.188,0.146 10 false 13 5.458,2.948 5.552,3.083 0.094,0.135 10 false 4 5.646,2.656 5.854,2.802 0.208,0.146 10 false TC 5.656,3.031 5.885,3.177 0.229,0.146 10 false CG 5.594,3.583 5.958,3.802 0.365,0.219 10 false G14 5.594,3.74 6.104,3.979 0.51,0.24 10 false DLC3 1.198,4.365 2.865,4.521 1.667,0.156 10 false : CAN Communication Line 1.396,1.427 2.021,1.719 0.625,0.292 10 false 23

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and CVT oil pressure calibration (for continuously variable transaxle).

K111: Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

K111F: Click hereDrivetrain>K111F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR


Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.INSPECT DLC3

DTC is output

2.INSPECT DLC3
a.
C146309C94
0.104,1.375 0.5,1.635 0.396,0.26 1.656,0.802 1.969,0.302 1.969,0.302 2.094,0.302 false 1.875,1.469 1.563,2.021 1.563,2.021 1.438,2.021 false 0.125,0.083 0.427,0.229 0.302,0.146 10 *a 2.156,0.208 2.458,0.354 0.302,0.146 10 CG 1.177,1.948 1.479,2.094 0.302,0.146 10 TC 0.177,1.427 0.51,1.635 0.333,0.208 10 G14
*a DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G14-13 (TC) - G14-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
3.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-13 (TC) - A62-23 (TC) Always Below 1 Ω
G14-13 (TC) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

Reconnect the A62 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (TC of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (TC of DLC3 INPUT)
a.
C146309C94
0.104,1.375 0.5,1.635 0.396,0.26 1.656,0.802 1.969,0.302 1.969,0.302 2.094,0.302 false 1.875,1.469 1.563,2.021 1.563,2.021 1.438,2.021 false 0.125,0.083 0.427,0.229 0.302,0.146 10 *a 2.156,0.208 2.458,0.354 0.302,0.146 10 CG 1.177,1.948 1.479,2.094 0.302,0.146 10 TC 0.177,1.427 0.51,1.635 0.333,0.208 10 G14
*a DLC3


Turn the ignition switch off.


b.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Turn the ignition switch to ON.


d.

Check that the malfunction indicator lamp is blinking.


Result:
Proceed to
Malfunction indicator lamp is blinking (for 2AR-FE)
Malfunction indicator lamp is blinking (for 3ZR-FE)
Malfunction indicator lamp is not blinking



Malfunction indicator lamp is blinking (for 2AR-FE)

Malfunction indicator lamp is blinking (for 3ZR-FE)

Malfunction indicator lamp is not blinking