Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048750 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in the speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the ignition switch from off to ON.

WIRING DIAGRAM

C240013E04
0.063,1.854 0.26,2.01 0.198,0.156 10 h1 0.063,2.01 2.021,2.177 1.958,0.167 10 Power Steering ECU Assembly 1.104,1.552 1.323,1.708 0.219,0.156 10 TS 1.396,1.458 1.521,1.604 0.125,0.146 10 5 5.365,1.542 6.927,1.885 1.563,0.344 10 Skid Control ECU (Brake Actuator Assembly) 5.656,2.656 5.854,2.813 0.198,0.156 10 TS 5.417,2.563 5.594,2.719 0.177,0.156 10 12 5.656,3.042 5.896,3.188 0.24,0.146 10 CG 5.469,2.948 5.563,3.094 0.094,0.146 10 4 5.708,3.594 6.052,3.792 0.344,0.198 10 G14 5.719,3.75 6.188,3.969 0.469,0.219 10 DLC3 1.198,4.375 2.917,4.521 1.719,0.146 10 : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly or steering column assembly has been replaced, perform the torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM


Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.INSPECT DLC3

DTC is output

2.INSPECT DLC3
a.
C146309C95
0.104,1.24 0.479,1.5 0.375,0.26 1.615,1.5 1.615,1.802 false 1.615,0.792 1.615,0.24 1.615,0.24 1.813,0.24 false 0.167,0.083 0.469,0.229 0.302,0.146 10 *a 1.844,0.156 2.146,0.302 0.302,0.146 10 CG 1.552,1.823 1.771,1.969 0.219,0.146 10 TS 0.167,1.292 0.521,1.531 0.354,0.24 10 G14
*a DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G14-12 (TS) - G14-4 (CG) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

5.INSPECT POWER STEERING ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (TS of DLC3 - POWER STEERING ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (TS of DLC3 - POWER STEERING ECU ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the h1 power steering ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-12 (TS) - h1-5 (TS) Always Below 1 Ω
G14-12 (TS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.

Reconnect the h1 power steering ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G14-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT POWER STEERING ECU ASSEMBLY
a.
C146309C95
0.104,1.24 0.479,1.5 0.375,0.26 1.615,1.5 1.615,1.802 false 1.615,0.792 1.615,0.24 1.615,0.24 1.813,0.24 false 0.167,0.083 0.469,0.229 0.302,0.146 10 *a 1.844,0.156 2.146,0.302 0.302,0.146 10 CG 1.552,1.823 1.771,1.969 0.219,0.146 10 TS 0.167,1.292 0.521,1.531 0.354,0.24 10 G14
*a DLC3


Turn the ignition switch off.


b.

Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.


SST
09843-18040  

c.

Turn the ignition switch to ON.


d.

Check that the power steering warning light is blinking.

Result:
Proceed to
The power steering warning light is not blinking
The power steering warning light is blinking




The power steering warning light is not blinking

REPLACE POWER STEERING ECU ASSEMBLY

The power steering warning light is blinking