Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0201  Injector Circuit / Open - (Cylinder 1)  P0202  Injector Circuit / Open - (Cylinder 2)  P0203  Injector Circuit / Open - (Cylinder 3)  P0204  Injector Circuit / Open - (Cylinder 4)  P062D  No. 1 Fuel Injector Driver Circuit Performance  


DESCRIPTION

The injector driver (EDU) delivers drive signals to injector assemblies using the DC/DC converter, which provides a high voltage and quick-charging system.

Soon after the injector driver (EDU) receives a fuel injection command (#1 to #4) signal from the ECM, the injector driver (EDU) responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector assembly.

A210270
1.135,5.646 1.552,5.885 0.417,0.24 2.594,5.677 3.031,5.938 0.438,0.26 4.229,5.875 4.635,6.125 0.406,0.25 5.667,6 6.063,6.25 0.396,0.25 3.396,0.115 3.729,0.281 0.333,0.167 10 EDU 2.563,1.469 3.229,1.865 0.667,0.396 10 DC/DC Converter 0.313,1.438 1.146,1.615 0.833,0.177 10 from Battery 0.313,2.208 1.406,2.385 1.094,0.177 10 Command Pulse 0.802,5.188 2.094,5.365 1.292,0.177 10 Confirmation Pulse 0.042,5.594 1.094,5.771 1.052,0.177 10 EDU Connector 0.281,0.063 1.688,0.24 1.406,0.177 10 EDU Wiring Diagram 0.656,3.625 0.99,3.792 0.333,0.167 10 ECM 1.51,2.479 1.781,2.646 0.271,0.167 10 IJt1 1.51,2.792 1.781,2.958 0.271,0.167 10 IJt4 1.51,3.094 1.781,3.26 0.271,0.167 10 IJt2 1.51,3.396 1.781,3.563 0.271,0.167 10 IJt3 1.552,4.01 1.75,4.177 0.198,0.167 10 IJf 1.51,4.625 1.802,4.792 0.292,0.167 10 IJen 1.479,3.708 1.802,3.875 0.323,0.167 10 IJt-R 1.479,4.313 1.802,4.479 0.323,0.167 10 IJf-R 5,2.458 5.354,2.625 0.354,0.167 10 INJ-1 5,0.573 5.427,0.74 0.427,0.167 10 INJ+R 5,0.896 5.396,1.063 0.396,0.167 10 INJ+3 5,1.208 5.396,1.375 0.396,0.167 10 INJ+2 5,1.531 5.396,1.698 0.396,0.167 10 INJ+4 5,1.854 5.396,2.021 0.396,0.167 10 INJ+1 5,2.792 5.354,2.958 0.354,0.167 10 INJ-4 5,3.094 5.354,3.26 0.354,0.167 10 INJ-2 5,3.417 5.354,3.583 0.354,0.167 10 INJ-3 5,3.74 5.385,3.906 0.385,0.167 10 INJ-R 3.229,3.25 3.698,3.583 0.469,0.333 10 Control Circuit 3.563,5.417 3.906,5.583 0.344,0.167 10 GND 1.823,7.083 5.063,7.448 3.24,0.365 10 CAUTION: Terminals L, M, N, O, P, Q, R and S are high voltage terminals. 1.188,5.677 1.708,5.948 0.521,0.271 10 B157 2.656,5.719 3.042,5.917 0.385,0.198 10 B158 4.281,5.917 4.792,6.198 0.51,0.281 10 B159 5.708,6.042 6.219,6.302 0.51,0.26 10 B160

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0201 Injector Circuit / Open - (Cylinder 1) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic).
·

Open or short in injector assembly circuit

·

Injector assembly

·

Injector driver (EDU)

·

ECM


Comes on DTC stored
P0202 Injector Circuit / Open - (Cylinder 2) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic).
·

Open or short in injector assembly circuit

·

Injector assembly

·

Injector driver (EDU)

·

ECM


Comes on DTC stored
P0203 Injector Circuit / Open - (Cylinder 3) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic).
·

Open or short in injector assembly circuit

·

Injector assembly

·

Injector driver (EDU)

·

ECM


Comes on DTC stored
P0204 Injector Circuit / Open - (Cylinder 4) Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic).
·

Open or short in injector assembly circuit

·

Injector assembly

·

Injector driver (EDU)

·

ECM


Comes on DTC stored
P062D No. 1 Fuel Injector Driver Circuit Performance Inconsistency in the injection waveforms between the injector driver (EDU) and ECM while the engine is running a certain number of times (a maximum of approx. 0.5 seconds) (1 trip detection logic).
·

Open or short in injector driver (EDU) circuit

·

Injector assembly

·

Injector driver (EDU)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

P0201, P0202, P0203, P0204:

The ECM compares injection command (#1 to #4) signals and injection confirmation (INJF) signals for each cylinder. If the ECM determines that a cylinder has a malfunction, DTC P0201, P0202, P0203 or P0204 will be stored.


P062D:

The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signals. This DTC will be stored if the ECM determines that the number of #1 to #4 signals and INJF signals are inconsistent.

The injector assemblies are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (EDU) (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector assembly current becomes too high, the voltage drop over the resistor exceeds a specified level and no INJF signal for that cylinder is sent to the ECM.

After the engine is started, when there is no injection confirmation (INJF) signal from the injector driver (EDU) to the ECM even though the ECM sends injection command (#1 to #4) signals to the injector driver (EDU), DTC P062D is stored.

If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.


A145849
4.958,2.469 4.625,2.865 false 4.635,3.25 4.875,3.552 false 0.115,0.021 1.698,0.229 1.583,0.208 10 Malfunction Detection: 2.604,0.656 3.01,0.854 0.406,0.198 10 ECM 0.063,1.76 1.75,1.979 1.688,0.219 10 Injection Command Signal 0.063,3.031 2.021,3.24 1.958,0.208 10 Injection Confirmation Signal 1.833,2.021 2.438,2.229 0.604,0.208 10 #1 to #4 2.063,2.781 2.417,2.99 0.354,0.208 10 INJF 3.302,1.76 3.583,1.958 0.281,0.198 10 ON 3.615,0.438 5.406,0.677 1.792,0.24 10 Command Signal (#1 to #4) 3.594,1.042 5.281,1.24 1.688,0.198 10 Confirmation Signal (INJF) 5.896,0.656 6.281,0.854 0.385,0.198 10 EDU 3.708,2.135 4.073,2.333 0.365,0.198 10 OFF 5.01,2.375 5.781,2.573 0.771,0.198 10 Abnormal 4.885,3.49 5.469,3.688 0.583,0.198 10 Normal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0201 Idling for 5 seconds
P0202
P0203
P0204
P062D

WIRING DIAGRAM

A205139
0.635,0.781 0.979,0.948 0.344,0.167 10 INJF 1.031,0.813 1.333,0.969 0.302,0.156 10 B53 1.042,1.25 1.344,1.406 0.302,0.156 10 B53 1.031,1.688 1.333,1.844 0.302,0.156 10 B53 1.031,2.115 1.333,2.271 0.302,0.156 10 B53 1.031,2.563 1.333,2.719 0.302,0.156 10 B53 1.031,3.063 1.333,3.219 0.302,0.156 10 B52 1.021,3.99 1.323,4.146 0.302,0.156 10 B52 1.125,0.615 1.24,0.771 0.115,0.156 10 8 0.677,1.219 0.969,1.385 0.292,0.167 10 #10 1.125,1.052 1.24,1.208 0.115,0.156 10 7 0.677,2.563 0.969,2.729 0.292,0.167 10 #40 1.125,1.49 1.24,1.646 0.115,0.156 10 3 0.677,1.698 0.969,1.865 0.292,0.167 10 #20 1.125,1.927 1.24,2.083 0.115,0.156 10 6 0.656,2.125 0.948,2.292 0.292,0.167 10 #30 6.219,0.781 6.563,0.948 0.344,0.167 10 INJF 6.219,1.219 6.51,1.385 0.292,0.167 10 #1 6.24,2.521 6.531,2.688 0.292,0.167 10 #4 6.219,2.094 6.51,2.26 0.292,0.167 10 #3 6.219,1.677 6.51,1.844 0.292,0.167 10 #2 5.854,0.813 6.135,0.969 0.281,0.156 10 B76 5.906,0.615 6.094,0.771 0.188,0.156 10 51 5.854,1.25 6.135,1.406 0.281,0.156 10 B76 5.896,1.052 6.094,1.208 0.198,0.156 10 50 5.844,1.688 6.125,1.844 0.281,0.156 10 B76 5.906,1.49 6.125,1.646 0.219,0.156 10 49 5.854,2.125 6.135,2.281 0.281,0.156 10 B76 5.906,1.927 6.125,2.083 0.219,0.156 10 48 5.865,2.563 6.146,2.719 0.281,0.156 10 B76 5.906,2.375 6.104,2.531 0.198,0.156 10 47 1.125,2.375 1.24,2.531 0.115,0.156 10 4 0.656,3.031 0.958,3.198 0.302,0.167 10 IJ1+ 1.125,2.865 1.24,3.021 0.115,0.156 10 1 4.26,3.156 4.375,3.313 0.115,0.156 10 2 3.594,3.135 3.708,3.292 0.115,0.156 10 1 1.125,4.208 1.24,4.365 0.115,0.156 10 3 1.104,6.615 1.219,6.771 0.115,0.156 10 3 1.125,5.719 1.24,5.875 0.115,0.156 10 1 1.125,3.802 1.24,3.958 0.115,0.156 10 4 1.125,5.115 1.24,5.271 0.115,0.156 10 6 3.427,3.344 3.802,3.521 0.375,0.177 10 B20 3.438,3.49 4.646,3.656 1.208,0.167 10 No. 1 Fuel Injector 3.438,4.688 3.771,4.865 0.333,0.177 10 B18 3.438,7.708 4.646,7.875 1.208,0.167 10 No. 4 Fuel Injector 3.438,6.156 3.771,6.333 0.333,0.177 10 B16 3.427,4.844 4.635,5.01 1.208,0.167 10 No. 2 Fuel Injector 3.438,7.542 3.771,7.719 0.333,0.177 10 B14 3.458,6.302 4.667,6.469 1.208,0.167 10 No. 3 Fuel Injector 4.302,4.479 4.417,4.635 0.115,0.156 10 2 3.604,4.479 3.719,4.635 0.115,0.156 10 1 4.271,5.99 4.385,6.146 0.115,0.156 10 2 3.583,5.979 3.698,6.135 0.115,0.156 10 1 4.271,7.323 4.385,7.479 0.115,0.156 10 2 3.604,7.323 3.719,7.479 0.115,0.156 10 1 0.677,3.99 0.948,4.156 0.271,0.167 10 IJ1- 1.031,4.417 1.333,4.573 0.302,0.156 10 B52 1.031,5.323 1.333,5.479 0.302,0.156 10 B52 1.042,5.885 1.344,6.042 0.302,0.156 10 B51 0.646,4.406 0.948,4.573 0.302,0.167 10 IJ2+ 0.646,5.302 0.917,5.469 0.271,0.167 10 IJ2- 0.677,5.896 0.979,6.063 0.302,0.167 10 IJ3+ 0.688,6.792 0.958,6.958 0.271,0.167 10 IJ3- 1.021,7.229 1.323,7.385 0.302,0.156 10 B52 1.042,8.146 1.344,8.302 0.302,0.156 10 B52 1.031,6.802 1.333,6.958 0.302,0.156 10 B51 1.125,7.042 1.25,7.198 0.125,0.156 10 2 1.104,7.948 1.219,8.104 0.115,0.156 10 5 0.656,7.24 0.958,7.406 0.302,0.167 10 IJ4+ 0.667,8.135 0.938,8.302 0.271,0.167 10 IJ4-

A284165
1.063,0.448 1.448,0.646 0.385,0.198 10 false B51 1.073,4.708 1.458,4.906 0.385,0.198 10 false B51 6.104,4.615 6.49,4.813 0.385,0.198 10 false A61 6.104,2.531 6.49,2.729 0.385,0.198 10 false A61 6.115,2.323 6.5,2.521 0.385,0.198 10 false 44 6.104,4.406 6.49,4.604 0.385,0.198 10 false 45 1.146,0.24 1.531,0.438 0.385,0.198 10 false 2 1.146,4.5 1.531,4.698 0.385,0.198 10 false 4 0.656,4.719 1.198,4.958 0.542,0.24 10 false GND 0.76,0.438 1.021,0.75 0.26,0.313 10 false +B 6.438,4.594 6.979,4.833 0.542,0.24 10 false MREL 6.438,2.552 6.979,2.792 0.542,0.24 10 false IREL 4.885,2.865 5.427,3.104 0.542,0.24 10 false EDU 3.927,2.104 4.469,2.344 0.542,0.24 10 false EDU 2.115,3.438 3.115,3.802 1,0.365 10 false EFI-MAIN NO. 2 2.708,4.604 3.219,5.021 0.51,0.417 10 false Battery 1.406,2.677 2.042,3.094 0.635,0.417 10 false EFI-MAIN NO. 2 3.135,2.698 3.771,3 0.635,0.302 10 false EFI NO. 1 6.542,5.167 6.938,5.552 0.396,0.385 10 false ECM 0.198,5.146 1.573,5.469 1.375,0.323 10 false Injector Driver (EDU) 4.573,1.813 4.771,2.01 0.198,0.198 10 false 5 5.354,1.802 5.552,2 0.198,0.198 10 false 3 4.615,2.635 4.813,2.833 0.198,0.198 10 false 2 5.354,2.625 5.552,2.823 0.198,0.198 10 false 1 2.021,2.438 2.219,2.635 0.198,0.198 10 false 5 2.833,2.438 3.031,2.635 0.198,0.198 10 false 3 2.01,3.188 2.208,3.385 0.198,0.198 10 false 2 2.854,3.188 3.052,3.385 0.198,0.198 10 false 1 1.396,3.885 2.396,4.25 1,0.365 10 false FL MAIN

CAUTION / NOTICE / HINT

CAUTION:

Make sure to perform work on high voltage circuits with the ignition switch off.


NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Engine does not start*1 A
Engine starts, but idling is rough*2 B
Except above C


HINT:
·

*1: Once DTC P062D is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).

When the engine cannot be started due to a malfunction in the injector driver (EDU), the value for "Fuel Press" is higher than the value for "Target Common Rail Pressure"

·

*2: DTC P0201, P0202, P0203, P0204 and P062D are stored at this time.





A

2.INSPECT ECM

B

9.CHECK WHETHER DTC OUTPUT RECURS

C

2.INSPECT ECM
a.
A294526
0.333,1.073 0.698,1.396 0.365,0.323 1.292,1.906 1.583,1.354 true 1.292,1.906 1.583,1.354 true 1.583,1.885 1.75,1.177 true 1.927,1.885 1.833,1.354 true 2.25,1.885 2.042,1.167 true 0.24,0.188 0.552,0.385 0.313,0.198 10 *a 1.802,1.927 2.115,2.125 0.313,0.198 10 #10 1.469,1.938 1.781,2.135 0.313,0.198 10 #20 1.135,1.938 1.448,2.135 0.313,0.198 10 #30 2.135,1.927 2.448,2.125 0.313,0.198 10 #40 2.948,3.427 3.333,3.604 0.385,0.177 10 GND 0.146,4.281 1.073,4.542 0.927,0.26 10 1 ms./DIV. 2.583,2.229 3.177,2.438 0.594,0.208 10 2 V/DIV. 0.375,1.135 0.833,1.333 0.458,0.198 10 B53
*a Front view of wire harness connector
(to Injector Driver (EDU))


Disconnect the injector driver (EDU) connector.


b.

Check the waveform of the injector driver (EDU) connectors using an oscilloscope while cranking the engine.

OK:
Tester Connection Condition Specified Condition
B53-7 (#10)- Body ground Cranking Correct waveform is as shown
B53-3 (#20) - Body ground Cranking Correct waveform is as shown
B53-6 (#30) - Body ground Cranking Correct waveform is as shown
B53-4 (#40) - Body ground Cranking Correct waveform is as shown



Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INJECTOR DRIVER (EDU))

NG

7.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)
3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF INJECTOR DRIVER (EDU))
a.
A204910C02
0.49,1.021 0.896,1.281 0.406,0.26 1.958,0.958 2.458,0.698 true 1.948,1.406 2.354,1.615 true 2.521,0.604 2.813,0.823 0.292,0.219 10 +B 2.406,1.573 2.792,1.792 0.385,0.219 10 GND 0.229,0.208 0.406,0.365 0.177,0.156 10 *a 0.552,1.063 0.854,1.229 0.302,0.167 10 B51
*a Front view of wire harness connector
(to Injector Driver (EDU))


Disconnect the injector driver (EDU) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B51-2 (+B) - B51-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)

NG

6.CHECK INJECTOR CIRCUIT
4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)
a.

Disconnect the injector driver (EDU) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B53-7 (#10) - B76-50 (#1) Always Below 1 Ω
B53-3 (#20) - B76-49 (#2) Always Below 1 Ω
B53-6 (#30) - B76-48 (#3) Always Below 1 Ω
B53-4 (#40) - B76-47 (#4) Always Below 1 Ω
B53-8 (INJF) - B76-51 (INJF) Always Below 1 Ω
B53-7 (#10) or B76-50 (#1) - Body ground Always 10 kΩ or higher
B53-3 (#20) or B76-49 (#2) - Body ground Always 10 kΩ or higher
B53-6 (#30) or B76-48 (#3) - Body ground Always 10 kΩ or higher
B53-4 (#40) or B76-47 (#4) - Body ground Always 10 kΩ or higher
B53-8 (INJF) or B76-51 (INJF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE INJECTOR DRIVER (EDU)

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE INJECTOR DRIVER (EDU)
a.

Replace the injector driver (EDU).

Click hereEngine / Hybrid System>1AD-FTV FUEL>INJECTOR DRIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CHECK INJECTOR CIRCUIT

Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER (EDU) - ECM)
a.

Disconnect the injector driver (EDU) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B53-7 (#10) - B76-50 (#1) Always Below 1 Ω
B53-3 (#20) - B76-49 (#2) Always Below 1 Ω
B53-6 (#30) - B76-48 (#3) Always Below 1 Ω
B53-4 (#40) - B76-47 (#4) Always Below 1 Ω
B53-8 (INJF) - B76-51 (INJF) Always Below 1 Ω
B53-7 (#10) or B76-50 (#1) - Body ground Always 10 kΩ or higher
B53-3 (#20) or B76-49 (#2) - Body ground Always 10 kΩ or higher
B53-6 (#30) or B76-48 (#3) - Body ground Always 10 kΩ or higher
B53-4 (#40) or B76-47 (#4) - Body ground Always 10 kΩ or higher
B53-8 (INJF) or B76-51 (INJF) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds.


e.

Start the engine and idle it for 30 seconds.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Check the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
HINT:
·

The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.

·

If the DTC P0201 is output, check the No. 1 injector assembly circuit.

·

If the DTC P0202 is output, check the No. 2 injector assembly circuit.

·

If the DTC P0203 is output, check the No. 3 injector assembly circuit.

·

If the DTC P0204 is output, check the No. 4 injector assembly circuit.




Result:
Proceed to
NEXT



NEXT

10.INSPECT INJECTOR DRIVER (EDU)
10.INSPECT INJECTOR DRIVER (EDU)
a.
A294527
0.375,0.667 0.688,0.885 0.313,0.219 0.385,0.938 0.708,1.156 0.323,0.219 0.813,0.948 1.135,1.167 0.323,0.219 0.802,0.667 1.125,0.885 0.323,0.219 0.115,0.115 0.427,0.313 0.313,0.198 10 *a 0.406,0.698 0.698,0.885 0.292,0.188 10 B20 0.417,0.969 0.708,1.156 0.292,0.188 10 B18 0.823,0.698 1.115,0.885 0.292,0.188 10 B16 0.844,0.979 1.135,1.167 0.292,0.188 10 B14 2.479,2.177 3.25,2.417 0.771,0.24 10 100 V/DIV. 0.156,4.271 1.073,4.521 0.917,0.25 10 1 ms./DIV. 3.021,4.052 3.333,4.25 0.313,0.198 10 GND
*a Front view of wire harness connector
(to Injector Assembly)


Disconnect the injector assembly connectors for all cylinders.

NOTICE:

If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.



b.

Check the waveform of the injector assembly connectors using an oscilloscope while cranking the engine.

OK:
Tester Connection Condition Specified Condition
B20-1 - B20-2 Cranking Voltage increases by 50 V or higher
B18-1 - B18-2 Cranking Voltage increases by 50 V or higher
B16-1 - B16-2 Cranking Voltage increases by 50 V or higher
B14-1 - B14-2 Cranking Voltage increases by 50 V or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

NG

14.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER (EDU))
11.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
13.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Perform the pilot quantity learning.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER (EDU))
a.

Disconnect the injector assembly connectors.


b.

Disconnect the injector driver (EDU) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B20-1 - B52-1 (IJ1+) Always Below 1 Ω
B20-2 - B52-4 (IJ1-) Always Below 1 Ω
B18-1 - B52-3 (IJ2+) Always Below 1 Ω
B18-2 - B52-6 (IJ2-) Always Below 1 Ω
B16-1 - B51-1 (IJ3+) Always Below 1 Ω
B16-2 - B51-3 (IJ3-) Always Below 1 Ω
B14-1 - B52-2 (IJ4+) Always Below 1 Ω
B14-2 - B52-5 (IJ4-) Always Below 1 Ω
B20-1 or B52-1 (IJ1+) - Body ground Always Below 1 Ω
B20-2 or B52-4 (IJ1-) - Body ground Always 10 kΩ or higher
B18-1 or B52-3 (IJ2+) - Body ground Always 10 kΩ or higher
B18-2 or B52-6 (IJ2-) - Body ground Always 10 kΩ or higher
B16-1 or B51-1 (IJ3+) - Body ground Always 10 kΩ or higher
B16-2 or B51-3 (IJ3-) - Body ground Always 10 kΩ or higher
B14-1 or B52-2 (IJ4+) - Body ground Always 10 kΩ or higher
B14-2 or B52-5 (IJ4-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.REPLACE INJECTOR DRIVER (EDU)

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.REPLACE INJECTOR DRIVER (EDU)
a.

Replace the injector driver (EDU).


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Start the engine and idle it for 5 seconds or more.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END