The EGR system recirculates exhaust gases. The recirculated gasses mix with the intake air so that the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.
In order to increase EGR circulation efficiency, the ECM adjusts the EGR valve angle and the throttle valve angle.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0400 | Exhaust Gas Recirculation Flow | Mass air flow rate is not changed when turning on the electric EGR control valve assembly while decelerating (2 trip detection logic). | ·
EGR valve deposit ·
EGR valve passage deposit ·
EGR pipe with cooler sub-assembly ·
Mass air flow meter assembly |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0400 | ·
MAF ·
Target EGR Position ·
Actual EGR Valve Pos. |
If the electric EGR control valve assembly is forcibly operated during deceleration but the intake air amount does not vary, the ECM determines that the electric EGR control valve assembly is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0400 | After warming up the engine, decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator pedal for approximately 5 seconds). |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0400 is output | A |
| DTC P0400 and other DTCs are output | B |
If any DTCs other than P0400 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close / All Data / MAF.
| Active Test Display |
|---|
| Activate the EGR Valve Close |
| Data List Display |
|---|
| MAF |
Read the MAF value when the EGR valve is closed using the Active Test function.
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
Before performing diagnosis, confirm that the EGR valve target opening angle is not 0%.
When "Coolant Temp" is 75°C (167°F) or higher during idle, the exhaust gas flows through the EGR pipe with cooler sub-assembly. If MAF does not change when the EGR is cut even though the EGR valve is operating normally, the EGR pipe with cooler sub-assembly may be clogged.
When idling while warming up the engine, the actuator operates and the EGR pipe with cooler sub-assembly is bypassed. However, if the connector of the No. 1 vacuum switching valve assembly (for EGR cooler) is disconnected, the EGR pipe with cooler sub-assembly is not bypassed and it is possible to check if the EGR pipe with cooler sub-assembly is clogged.
| Active Test | Result | Proceed to |
|---|---|---|
| Activate the EGR Valve Close:
OFF (Open) to Close |
MAF value does not change | A |
| MAF value changes | B |
As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
The problem may be a temporary, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter assembly.
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
|---|---|---|
| Open (67%) | ·
Atmosphere pressure: 101 kPa ·
Intake air temperature: 30°C (86°F) ·
Engine coolant temperature: 88°C (190°F) |
3 to 12 gm/sec |
| Closed (0%) | 7 gm/sec or more |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
| Tester Display |
|---|
| MAF |
| GTS Display | Condition | Standard |
|---|---|---|
| MAF | Ignition switch ON (do not start engine) | 0.35 gm/sec or less |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / All Data / EGR Cooler Bypass Position and MAF.
| Active Test Display |
|---|
| Activate the VSV for EGR Cooler Bypass |
| Data List Display |
|---|
| MAF |
| EGR Cooler Bypass Position |
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
Using the Active Test function, switch the No. 1 vacuum switching valve assembly (for EGR cooler) between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass |
MAF value does not change | A |
| MAF value changes | B |
If the EGR pipe with cooler sub-assembly is clogged, the MAF value changes.
A
B
Remove the electric EGR control valve assembly, No. 2 intake manifold and intake manifold.
Click hereEngine / Hybrid System>1AD-FTV EMISSION CONTROL>EGR VALVE>REMOVAL
Visually check the electric EGR control valve assembly, No. 2 intake manifold and intake manifold for deposits. If there are deposits, clean the electric EGR control valve assembly, No. 2 intake manifold and intake manifold.
| *1 | No. 2 Intake Manifold | *2 | Electric EGR Control Valve Assembly |
| *3 | Intake Manifold | - | - |
| *a | Carbon Deposit | - | - |
When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.
When cleaning the electric EGR control valve assembly, perform initialization procedure.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.
When cleaning the electric EGR control valve assembly, care should be taken to prevent the ingress of cleaning solvent into the bearings of valve shaft, and when wiping off deposits on the electric EGR control valve assembly, care should be taken not to push the deposits into the bearings of valve shaft. These contaminants may adversely affect on the function of electric EGR control valve assembly.
Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.
If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
If the EGR valve does not close properly or is stuck open, the amount of recirculated exhaust gas becomes excessive and combustion becomes unstable. Also, there may be a lack of power.
Remove the intake manifold from the cylinder head when it has to be cleaned.
Reinstall the electric EGR control valve assembly, No. 2 intake manifold and intake manifold.
Click hereEngine / Hybrid System>1AD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the EGR pipe with cooler sub-assembly.
Click hereEngine / Hybrid System>1AD-FTV EMISSION CONTROL>EGR COOLER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up.
Move the shift lever to 2nd gear and decelerate from a speed of 50 km/h (31 mph) or more (fully release the accelerator for approximately 5 seconds or more).
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
When a DTC is output, the mass air flow meter assembly may be malfunctioning.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the mass air flow meter assembly.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
If foreign matter is stuck inside the mass air flow meter assembly, the output characteristics of the mass air flow meter assembly may change, resulting in a malfunction.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / All Data / EGR Cooler Bypass Position and MAF.
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
| Active Test Display |
|---|
| Activate the VSV for EGR Cooler Bypass |
| Data List Display |
|---|
| MAF |
| EGR Cooler Bypass Position |
Using the Active Test function, switch the No. 1 vacuum switching valve assembly (for EGR cooler) between "Cooler" and "Bypass" a few times, and then check whether the MAF value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass |
MAF value does not change | A |
| MAF value changes | B |
If the EGR pipe with cooler sub-assembly is clogged, the MAF value changes.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up.
Move the shift lever to 2nd gear and decelerate from a speed of 50 km/h (31 mph) or more (fully release the accelerator for approximately 5 seconds or more).
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
When a DTC is output, the mass air flow meter assembly may be malfunctioning.
| Proceed to |
|---|
| NEXT |
NEXT