Home › Engine / Hybrid System › 1AD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008376 1AD-FTV INTAKE / EXHAUST _0046746 INTAKE MANIFOLD A

1AD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.



PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A291346C01
0.958,3.573 1.271,3.729 0.313,0.156 10 *a 2.25,3.333 2.563,3.49 0.313,0.156 10 *b 2.26,4.031 2.573,4.188 0.313,0.156 10 *c
*a 35 mm (1.38 in.)
*b 20 mm (0.787 in.)
*c 13 mm (0.512 in.)


Using an E8 "TORX" wrench, install the 2 stud bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 17111 2.INSTALL INTAKE MANIFOLD

a.

Install a new gasket to the cylinder head.

HINT:
A273043N01
2.479,0.854 2.615,0.448 2.615,0.448 2.698,0.448 true 2.75,0.333 2.906,0.531 0.156,0.198 10 A

Install the gasket with the part labeled A facing the right side of the vehicle as shown in the illustration.



b.
A273044C01
0.583,1.896 0.896,2.052 0.313,0.156 10 *1 1.031,1.615 1.188,1.813 0.156,0.198 10 A 2.208,1.615 2.365,1.813 0.156,0.198 10 A 0.208,0.177 0.365,0.375 0.156,0.198 10 B 3.167,0.198 3.323,0.396 0.156,0.198 10 B 1.635,0.125 1.792,0.323 0.156,0.198 10 B 3.01,1.521 3.167,1.719 0.156,0.198 10 B 0.333,1.49 0.49,1.688 0.156,0.198 10 B
*1 Nut


Install the intake manifold with the 7 bolts and 2 nuts.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

Bolt Length:
Item Length
Bolt A 90 mm (3.54 in.)
Bolt B 25 mm (0.984 in.)



Hide 25770A 3.CONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

a.

Connect the No. 2 vacuum transmitting hose assembly to the intake manifold, and slide the clamp to secure the hose.


Hide 17112 4.INSTALL NO. 2 INTAKE MANIFOLD

a.

Install a new gasket and the No. 2 intake manifold with the bolt and 2 nuts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 12631A 5.INSTALL ENGINE COVER BRACKET

a.

Install the engine cover bracket with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 17696 6.INSTALL GAS FILTER BRACKET

a.

Install the gas filter bracket with the 2 bolts.

Torque:
8.8 N*m (90 kgf*cm, 78 in.*lbf)


Hide 23265 7.INSTALL NO. 1 GAS FILTER

a.
A206313C01
1.396,2.625 2.479,2.625 true 1.406,3.094 2.49,3.094 true 2.521,2.531 2.833,2.688 0.313,0.156 10 *1 2.521,2.99 2.833,3.146 0.313,0.156 10 *2
*1 Protrusion
*2 Groove


Install the No. 1 gas filter to the gas filter bracket.

NOTICE:

Make sure the protrusion of the No. 1 gas filter is aligned with the groove of the gas filter bracket.



b.

Connect the vacuum hose.


Hide 11452 9.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring to the engine oil level dipstick guide.


b.

Install the engine oil level dipstick guide with the 2 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


c.

Connect the connector and attach the wire harness clamp to the engine oil level dipstick guide.


d.

Install the engine oil level dipstick.


Hide 17853B 10.INSTALL INTAKE MANIFOLD INSULATOR

a.

Install the intake manifold insulator to the intake manifold.


Hide 23810A 11.INSTALL COMMON RAIL ASSEMBLY

Hide 23701 12.INSTALL INJECTION PIPE SUB-ASSEMBLY

Hide 23804C 13.INSTALL FUEL INLET PIPE SUB-ASSEMBLY

Hide 25800 14.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY

Hide 25602 15.INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY

Hide 16296 16.CONNECT NO. 8 WATER BY-PASS HOSE

Hide 16295 17.INSTALL NO. 7 WATER BY-PASS HOSE

a.

Install the No. 7 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


Hide 25625 18.INSTALL EGR VALVE BRACKET

Hide 26100 20.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 21.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION