Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  


DESCRIPTION

The ECM opens and closes the throttle valve using a DC motor type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

Although the DTC title says "Exhaust Gas Recirculation Throttle Position Control Range / Performance", this DTC indicates that the throttle valve is malfunctioning.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance The throttle motor activation duty is more than specified value for 30 seconds (1 trip detection logic).
·

Throttle valve stuck

·

Throttle valve does not move smoothly

·

Open or short in throttle control motor circuit

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0488
·

Actual Throttle Position

·

Target Throttle Position

·

Throttle Motor DUTY

·

Throttle Close Learning Val.

·

Diesel Throttle Learn Status



Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the DC motor with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

Normal Condition
Throttle Condition Target Throttle Position Actual Throttle Position Throttle Close Learning Val. Diesel Throttle Learn Status
Throttle Valve Fully Closed 100% 100% 14 to 21.25 deg OK
Throttle Valve Fully Open 0% 0%

A206049
4.573,2.135 4.708,1.792 false 4.563,2.896 4.698,2.563 false 4.563,3.646 4.698,3.302 false 4.698,4.479 4.594,4.188 false 5.302,5.24 5.125,5.031 false 3.448,5.198 3.219,5.021 false 0.25,5.438 1.646,5.802 1.396,0.365 10 Duty Ratio Malfunction Counter 0.094,0.031 1.875,0.24 1.781,0.208 10 Malfunction Detection: 0.25,1.25 1.656,1.615 1.406,0.365 10 Throttle Valve Target Opening Angle 0.25,2.708 1.729,3.104 1.479,0.396 10 Throttle Valve Actual Opening Angle 0.906,4.125 1.646,4.344 0.74,0.219 10 Duty Ratio 4.75,1.719 5.344,1.917 0.594,0.198 10 Normal 4.75,2.479 5.5,2.677 0.75,0.198 10 Abnormal 4.75,4.375 5.344,4.573 0.594,0.198 10 Normal 4.75,3.219 5.5,3.417 0.75,0.198 10 Abnormal 5.906,0.594 6.354,0.792 0.448,0.198 10 Open 5.906,1.354 6.385,1.552 0.479,0.198 10 Close 5.906,2.063 6.354,2.26 0.448,0.198 10 Open 5.906,2.823 6.385,3.021 0.479,0.198 10 Close 5.906,3.573 6.417,3.781 0.51,0.208 10 100% 5.906,4.333 6.25,4.531 0.344,0.198 10 0% 3.49,5.104 4.521,5.313 1.031,0.208 10 Stores P0488 5.302,5.24 6.094,5.448 0.792,0.208 10 Threshold 3.469,6.271 3.875,6.479 0.406,0.208 10 Time

HINT:
·

If carbon deposits exist in the diesel throttle body assembly, the following parts may also have deposits inside: electric EGR control valve assembly, intake manifold, exhaust fuel addition injector, DPF catalyst, other parts related to the exhaust gas.

By removing the electric EGR control valve assembly from the intake manifold, the carbon deposit condition between the electric EGR control valve assembly and intake manifold can be checked visually. When checking for deposits in the electric EGR control valve assembly, hold the EGR valve to a light and confirm that the valve contacts the valve seat securely.

A291598
4.917,0.552 4.75,0.552 4.75,0.552 4.75,1.219 false 5.667,2.583 5.5,2.583 5.5,2.583 5.5,1.906 false 4.969,0.427 6.698,0.719 1.729,0.292 10 *1 5.719,2.469 6.74,2.656 1.021,0.188 10 *2
*1 Electric EGR Control Valve Assembly *2 No. 2 EGR Pipe


·

DPF catalyst diagnosis:

The value of "Catalyst Differential Press" in the Data List is high when the catalyst is clogged. If this value exceeds approximately 0.4, DTC P244B is stored.

If the "Catalyst Differential Press" become near about 0.4, the catalyst is probably clogged with PM even if DTC P244B is not present.

Check the Catalyst Differential Press when the engine is running at 3000 rpm with no load. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Catalyst Differential Press.

If the value of MAF in the Data List is less than 25 gm/sec, a correct value for Catalyst Differential Press is not output due to exhaust gas pulsation.

·

Exhaust fuel addition injector assembly diagnosis:

When the fuel volume injected by the exhaust fuel addition injector assembly decreases, the value of "Exhaust Fuel Addition FB" in the Data List increases. Exhaust Fuel Addition FB in the Data List is a correction value to increase the fuel volume injected from the exhaust fuel addition injector assembly when the catalyst temperature does not rise to the target during catalyst regeneration. Under normal conditions, the value is between 0.9 and 1.45.

Check the value by entering the following menus on an GTS: Powertrain / Engine and ECT / Data List / All Data / Exhaust Fuel Addition FB. Under normal conditions, the exhaust gas temperature becomes 150 to 350°C (302 to 662°F) when the vehicle is driven in 3rd gear at a constant vehicle speed of about 50 km/h (31 mph). While driving under these conditions, the exhaust gas temperature rises to 500 to 700°C (932 to 1292°F) when the catalyst regeneration function in the Active Test (Activate the DPF Rejuvenate (PM)) is performed. If the temperature does not rise sufficiently, the exhaust fuel addition injector assembly or the DPF catalyst may be damaged.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0488 Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.

WIRING DIAGRAM

A206856E08
1.25,1.302 1.583,0.292 1.583,0.292 1.688,0.292 false 1.125,0.76 0.99,0.302 0.99,0.302 0.885,0.302 false 1.135,2.094 0.813,2.594 0.813,2.594 0.938,2.594 false 5.833,4.229 6.26,4.406 0.427,0.177 10 false ECM 1.844,1.792 2.052,1.938 0.208,0.146 10 false E2 1.771,1.292 2.094,1.438 0.323,0.146 10 false VTA 1.833,0.76 2.073,0.906 0.24,0.146 10 false VC 5.531,2.021 5.948,2.167 0.417,0.146 10 false EVLU 5.531,1.26 5.854,1.406 0.323,0.146 10 false VLU 5.5,0.76 5.927,0.906 0.427,0.146 10 false VCVL 2.188,1.781 2.313,1.958 0.125,0.177 10 false 3 2.167,0.719 2.281,0.896 0.115,0.177 10 false 5 2.177,1.25 2.302,1.427 0.125,0.177 10 false 6 5.219,0.708 5.406,0.885 0.188,0.177 10 false 97 5.156,1.281 5.417,1.458 0.26,0.177 10 false 119 5.229,1.813 5.406,1.99 0.177,0.177 10 false 96 5.833,4.063 6.104,4.229 0.271,0.167 10 false B76 0.729,3.677 0.917,3.833 0.188,0.156 10 false B3 1.823,2.417 2.063,2.583 0.24,0.167 10 false M+ 5.531,2.406 5.771,2.573 0.24,0.167 10 false M+ 5.521,2.948 5.708,3.115 0.188,0.167 10 false M- 1.844,2.938 2.031,3.104 0.188,0.167 10 false M- 5.531,3.375 5.927,3.531 0.396,0.156 10 false GE01 3.25,3.281 3.833,3.438 0.583,0.156 10 false Shielded 0.729,3.844 3.094,4.271 2.365,0.427 10 false Diesel Throttle Body Assembly 2.188,2.292 2.292,2.469 0.104,0.177 10 false 2 2.188,2.833 2.292,2.99 0.104,0.156 10 false 1 5.219,2.323 5.396,2.469 0.177,0.146 10 false 42 5.219,2.844 5.438,3.01 0.219,0.167 10 false 43 5.229,3.292 5.417,3.469 0.188,0.177 10 false 82 1.729,0.229 2.198,0.417 0.469,0.188 10 false Hall IC 0.969,2.5 1.5,2.688 0.531,0.188 10 false Magnet 0.375,0.219 0.906,0.406 0.531,0.188 10 false Magnet

CAUTION / NOTICE / HINT

NOTICE:
·

When cleaning the electric EGR control valve assembly or diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0488)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0488 is output A
DTC P0488 and other DTCs are output B


HINT:
·

If any DTCs other than DTC P0488 are output, troubleshoot those DTCs first.

·

Be sure to also record the values of "Actual Throttle Position" and "Target Throttle Position" listed in the freeze frame data.





A

2.READ VALUE USING GTS (DIESEL THROTTLE LEARN STATUS)

B

2.READ VALUE USING GTS (DIESEL THROTTLE LEARN STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds or more.

HINT:

Be sure to turn off the ignition switch before performing this inspection. The fully closed position of the diesel throttle valve is learned when the ignition switch is turned off.



e.

Turn the ignition switch to ON and turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Diesel Throttle Learn Status.

Powertrain > Engine > Data List
Tester Display
Diesel Throttle Learn Status
50003 61 428

g.

Read the values when the ignition switch is ON.

Standard:

Diesel Throttle Learn Status is OK


NOTICE:

Extremely cold conditions might cause the throttle valve movement to be delayed.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)

NG

8.REMOVE DEPOSIT (CLEAN EGR PASSAGE)
3.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / All Data / Actual Throttle Position.

Powertrain > Engine > Active Test
Active Test Display
Diesel Throttle Target Angle
Data List Display
Actual Throttle Position
50004 61 239 406

d.

When changing the Active Test continuously value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



Result:
Proceed to
OK
NG



OK

4.REMOVE DEPOSIT (CLEAN EGR PASSAGE)

NG

8.REMOVE DEPOSIT (CLEAN EGR PASSAGE)
4.REMOVE DEPOSIT (CLEAN EGR PASSAGE)
a.

Remove the electric EGR control valve assembly, No. 2 intake manifold and intake manifold.

Click hereEngine / Hybrid System>1AD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


b.

Remove the deposits from those parts and clean the parts.

A291599
2.563,0.813 2.25,0.25 2.25,0.25 2.083,0.25 false 3.958,1.219 3.677,0.25 3.677,0.25 3.51,0.25 false 5.708,4.302 5.708,3.344 false 2.844,2.333 3.417,3.667 3.417,3.667 3.583,3.667 false 5.51,1.896 5.51,1.49 false 1.917,0.167 2.229,0.323 0.313,0.156 10 *1 3.344,0.167 3.656,0.323 0.313,0.156 10 *2 5.646,4.333 5.958,4.49 0.313,0.156 10 *a 3.667,3.583 3.979,3.74 0.313,0.156 10 *3 5.667,0.25 5.979,0.406 0.313,0.156 10 *1 5.667,2.417 5.979,2.573 0.313,0.156 10 *3 5.448,1.917 5.76,2.073 0.313,0.156 10 *a
*1 No. 2 Intake Manifold *2 Electric EGR Control Valve Assembly
*3 Intake Manifold - -
*a Carbon Deposit - -


NOTICE:
·

When cleaning the electric EGR control valve assembly and diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.



HINT:

Remove the intake manifold from the cylinder head when it has to be cleaned.



Result:
Proceed to
NEXT



NEXT

5.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
5.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
a.

Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.

OK:

Throttle valve moves smoothly.


NOTICE:

Take care not to damage the throttle valve or valve housing.



Result:
Proceed to
OK
NG



OK

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)

NG

6.REPLACE DIESEL THROTTLE BODY ASSEMBLY
6.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
a.

Start the engine and warm it up.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed, Target Throttle Position and Actual Throttle Position.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Target Throttle Position
Actual Throttle Position
50003 61 315,607,406

e.

Take a snapshot with the GTS.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / All Data / Actual Throttle Position.

Powertrain > Engine > Active Test
Active Test Display
Diesel Throttle Target Angle
Data List Display
Actual Throttle Position
50004 61 239 406
HINT:

The movement of the throttle valve can be determined by performing the following inspection.



g.

When changing the Active Test value continuously to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



h.

Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

END

NG

11.REPLACE ECM
8.REMOVE DEPOSIT (CLEAN EGR PASSAGE)
a.

Remove the electric EGR control valve assembly, No. 2 intake manifold and intake manifold.

Click hereEngine / Hybrid System>1AD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL


b.

Remove the deposits from those parts and clean the parts.

A291599
2.563,0.813 2.25,0.25 2.25,0.25 2.083,0.25 false 3.958,1.219 3.677,0.25 3.677,0.25 3.51,0.25 false 5.708,4.302 5.708,3.344 false 2.844,2.333 3.417,3.667 3.417,3.667 3.583,3.667 false 5.51,1.896 5.51,1.49 false 1.917,0.167 2.229,0.323 0.313,0.156 10 *1 3.344,0.167 3.656,0.323 0.313,0.156 10 *2 5.646,4.333 5.958,4.49 0.313,0.156 10 *a 3.667,3.583 3.979,3.74 0.313,0.156 10 *3 5.667,0.25 5.979,0.406 0.313,0.156 10 *1 5.667,2.417 5.979,2.573 0.313,0.156 10 *3 5.448,1.917 5.76,2.073 0.313,0.156 10 *a
*1 No. 2 Intake Manifold *2 Electric EGR Control Valve Assembly
*3 Intake Manifold - -
*a Carbon Deposit - -


NOTICE:
·

When cleaning the electric EGR control valve assembly and diesel throttle body assembly, use a piece of cloth soaked with cleaning solvent. Spraying solvent directly onto these parts or soaking the parts in solvent may damage the parts.

·

Extreme care must be taken to prevent the removed deposits from falling into the engine unit during cleaning.



HINT:

Remove the intake manifold from the cylinder head when it has to be cleaned.



Result:
Proceed to
NEXT



NEXT

9.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
9.INSPECT DIESEL THROTTLE BODY ASSEMBLY (THROTTLE VALVE MOVEMENT)
a.

Using your finger, move the throttle valve from the fully open position to the fully closed position and check that it moves smoothly.

OK:

Throttle valve moves smoothly.


NOTICE:

Take care not to damage the throttle valve or valve housing.



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)

NG

6.REPLACE DIESEL THROTTLE BODY ASSEMBLY
10.CHECK HARNESS AND CONNECTOR (DIESEL THROTTLE BODY ASSEMBLY - ECM)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B3-5 (VC) - B76-97 (VCVL) Always Below 1 Ω
B3-6 (VTA) - B76-119 (VLU) Always Below 1 Ω
B3-3 (E2) - B76-96 (EVLU) Always Below 1 Ω
B3-2 (M+) - B76-42 (M+) Always Below 1 Ω
B3-1 (M-) - B76-43 (M-) Always Below 1 Ω
B3-5 (VC) or B76-97 (VCVL) - Body ground Always 10 kΩ or higher
B3-6 (VTA) or B76-119 (VLU) - Body ground Always 10 kΩ or higher
B3-3 (E2) or B76-96 (EVLU) - Body ground Always 10 kΩ or higher
B3-2 (M+) or B76-42 (M+) - Body ground Always 10 kΩ or higher
B3-1 (M-) or B76-43 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
a.

Start the engine and warm it up.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed, Target Throttle Position and Actual Throttle Position.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Target Throttle Position
Actual Throttle Position
50003 61 315,607,406

e.

Take a snapshot with the GTS.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Diesel Throttle Target Angle / All Data / Actual Throttle Position.

Powertrain > Engine > Active Test
Active Test Display
Diesel Throttle Target Angle
Data List Display
Actual Throttle Position
50004 61 239 406
HINT:

The movement of the throttle valve can be determined by performing the following inspection.



g.

When changing the Active Test value continuously to 0, 30, 60, 90, 60, 30 and 0%, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



h.

Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from an idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)