Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and sets the DTC.

HINT:

The normal conditions are as shown in the table below.


Signals (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signals off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM


Does not come on DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0504 Depress and release brake pedal with ignition switch ON

WIRING DIAGRAM

A160611
1.167,0.885 2.24,1.094 1.073,0.208 10 from IG2 Relay 1.354,1.865 2.24,2.073 0.885,0.208 10 from Battery 2.792,0.708 3.104,0.865 0.313,0.156 10 IGN 2.76,1.042 2.896,1.198 0.135,0.156 10 1 3.01,1.042 3.146,1.198 0.135,0.156 10 2 2.76,2.021 2.896,2.177 0.135,0.156 10 1 4.563,1.802 4.698,1.958 0.135,0.156 10 1 5.906,3.104 6.292,3.26 0.385,0.156 10 ECM 3.01,2.021 3.146,2.177 0.135,0.156 10 2 3.438,1.802 3.573,1.958 0.135,0.156 10 2 4.563,0.813 4.698,0.969 0.135,0.156 10 3 5.333,0.813 5.531,0.969 0.198,0.156 10 34 5.333,1.792 5.531,1.948 0.198,0.156 10 35 5.615,0.813 5.958,0.969 0.344,0.156 10 ST1- 5.615,1.792 5.958,1.948 0.344,0.156 10 STP 3.438,0.813 3.573,0.969 0.135,0.156 10 4 2.74,1.708 3.146,1.865 0.406,0.156 10 STOP 3.479,2.396 4.615,2.583 1.135,0.188 10 Stop Light Switch 5.906,2.958 6.208,3.125 0.302,0.167 10 A61 3.469,2.208 3.656,2.375 0.188,0.167 10 A5

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch.

5.

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A148738
0.573,1.688 1.021,1.958 0.448,0.271 0.406,0.26 0.625,0.438 0.219,0.177 10 false *a 0.708,1.74 0.896,1.917 0.188,0.177 10 false A5
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-2 - Body ground Always 11 to 14 V
A5-4 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

7.REPLACE STOP LAMP SWITCH ASSEMBLY
3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A275087C02
0.281,2.615 0.667,2.875 0.385,0.26 2.167,4.198 1.677,3.677 true 2.604,2.771 1.76,3.667 true 0.49,0.365 0.802,0.521 0.313,0.156 10 *a 2.365,0.396 2.677,0.552 0.313,0.156 10 *b 1.594,2.49 1.906,2.646 0.313,0.156 10 *c 0.354,2.667 0.813,2.865 0.458,0.198 10 A61 2.667,2.656 3.323,2.844 0.656,0.188 10 35 (STP) 2.021,4.219 2.719,4.417 0.698,0.198 10 34 (ST1-)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
A61-34 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V
A61-35 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Release and depress the brake pedal.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

7.REPLACE STOP LAMP SWITCH ASSEMBLY
a.

Replace the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED