Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P052F  Glow Plug Control Module System Voltage  P0683  Glow Plug Control Module to PCM Communication Circuit  


DESCRIPTION

The glow system consists of the glow plug controller, glow plug assemblies and ECM. The glow plug controller turns on the glow plug assembly of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plug assemblies can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.

The glow plug assemblies are turned on during PM forced regeneration in order to prevent the engine speed from rising due to an increase in fuel injection volume used to increase the exhaust gas temperature. The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P052F Glow Plug Control Module System Voltage The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plug assemblies are on (2 trip detection logic). Glow plug controller Comes on DTC stored
P0683 Glow Plug Control Module to PCM Communication Circuit When the glow plug assemblies are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (2 trip detection logic).
·

Open circuit in GND wire

·

Open or short circuit in BATT wire

·

Open in SI wire

·

SI wire short circuit to ground or battery

·

Open in DI wire

·

DI wire short circuit to ground or battery

·

Low battery voltage

·

Glow plug controller

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P052F Enter check mode
P0683

WIRING DIAGRAM

A298537
0.542,5.021 3.604,5.219 3.063,0.198 10 false Glow Plug Controller 2.708,1.531 4.385,1.771 1.677,0.24 10 false No. 1 Glow Plug Assembly 2.708,2.167 4.396,2.375 1.688,0.208 10 false No. 2 Glow Plug Assembly 2.708,2.792 4.583,2.969 1.875,0.177 10 false No. 3 Glow Plug Assembly 2.708,3.438 4.552,3.677 1.844,0.24 10 false No. 4 Glow Plug Assembly 1.448,5.656 2.104,5.906 0.656,0.25 10 false GLOW 1.583,6.281 2.875,6.51 1.292,0.229 10 false EFI-MAIN NO. 2 3.677,6.729 5.208,7.073 1.531,0.344 10 false EFI-MAIN NO. 2 0.542,6.406 1.427,6.729 0.885,0.323 10 false FL MAIN 0.688,6.938 1.573,7.26 0.885,0.323 10 false Battery 6.406,7.25 7.125,7.573 0.719,0.323 10 false ECM 1.375,0.469 2.031,0.719 0.656,0.25 10 false SI 1.375,0.885 2.031,1.135 0.656,0.25 10 false DI 1.281,1.26 1.938,1.51 0.656,0.25 10 false GL1 1.281,1.896 1.938,2.146 0.656,0.25 10 false GL2 1.271,2.542 1.927,2.792 0.656,0.25 10 false GL3 1.26,3.188 1.917,3.438 0.656,0.25 10 false GL4 1.333,3.813 1.99,4.063 0.656,0.25 10 false +B 1.188,4.167 1.844,4.417 0.656,0.25 10 false BATT 1.24,4.563 1.896,4.813 0.656,0.25 10 false GND 1.688,0.49 2.344,0.74 0.656,0.25 10 false W1 1.688,0.896 2.344,1.146 0.656,0.25 10 false W1 1.688,3.823 2.344,4.073 0.656,0.25 10 false W1 1.698,4.563 2.354,4.813 0.656,0.25 10 false W1 1.688,4.177 2.344,4.427 0.656,0.25 10 false W4 1.688,3.198 2.344,3.448 0.656,0.25 10 false W3 1.688,2.552 2.344,2.802 0.656,0.25 10 false W3 1.688,1.917 2.344,2.167 0.656,0.25 10 false W2 1.688,1.271 2.344,1.521 0.656,0.25 10 false W2 1.771,0.281 2.021,0.5 0.25,0.219 10 false 3 1.781,0.698 2.031,0.917 0.25,0.219 10 false 5 1.781,1.094 2.031,1.313 0.25,0.219 10 false 1 1.781,1.719 2.031,1.938 0.25,0.219 10 false 2 1.771,2.344 2.021,2.563 0.25,0.219 10 false 1 1.771,3 2.021,3.219 0.25,0.219 10 false 2 1.771,3.615 2.021,3.833 0.25,0.219 10 false 4 1.771,4 2.021,4.219 0.25,0.219 10 false 1 1.771,4.385 2.021,4.604 0.25,0.219 10 false 1 5.823,0.281 6.073,0.5 0.25,0.219 10 false 57 5.781,0.49 6.438,0.74 0.656,0.25 10 false B76 5.781,0.896 6.438,1.146 0.656,0.25 10 false B76 5.781,4.99 6.438,5.24 0.656,0.25 10 false B76 5.781,6.417 6.438,6.667 0.656,0.25 10 false A61 5.833,0.698 6.083,0.917 0.25,0.219 10 false 56 5.813,4.781 6.063,5 0.25,0.219 10 false 58 5.833,6.219 6.083,6.438 0.25,0.219 10 false 45 6.177,6.417 6.833,6.667 0.656,0.25 10 false MREL 6.177,4.99 6.833,5.24 0.656,0.25 10 false GREL 6.177,0.885 6.833,1.135 0.656,0.25 10 false GLDI 6.177,0.5 6.833,0.75 0.656,0.25 10 false GLDO 3.135,5.302 3.792,5.552 0.656,0.25 10 false B38 3.135,5.479 5.094,5.729 1.958,0.25 10 false Glow Plug Relay Assembly 4.49,6.313 4.74,6.531 0.25,0.219 10 false 1 4.49,6.01 4.74,6.229 0.25,0.219 10 false 3 3.698,6.323 3.948,6.542 0.25,0.219 10 false 2 3.698,6 3.948,6.219 0.25,0.219 10 false 5 3.396,4.885 3.646,5.104 0.25,0.219 10 false 1 3.396,4.583 3.646,4.802 0.25,0.219 10 false 4 4.167,4.583 4.417,4.802 0.25,0.219 10 false 3 4.177,4.865 4.427,5.083 0.25,0.219 10 false 2 3.25,3.948 4.625,4.146 1.375,0.198 10 false EFI NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P0683 is output A
DTC P052F is output B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)

B

17.REPLACE GLOW PLUG CONTROLLER
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF GLOW PLUG CONTROLLER)
a.
A241954
0.594,0.958 1.031,1.229 0.438,0.271 1.781,1.177 2.063,1.719 true 0.167,0.156 0.427,0.375 0.26,0.219 10 false *a 1.979,1.74 2.281,1.917 0.302,0.177 10 false +B 0.698,1.01 1.354,1.313 0.656,0.302 10 false W1
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W1-4 (+B) - Body ground Ignition switch ON 11 to 14 V
W1-4 (+B) - Body ground Ignition switch off Below 0.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)

NG

10.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)
a.

Disconnect the glow plug controller connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W1-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
a.

Disconnect the glow plug controller connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W1-3 (SI) - B76-57 (GLDO) Always Below 1 Ω
W1-5 (DI) - B76-56 (GLDI) Always Below 1 Ω
W1-3 (SI) or B76-57 (GLDO) - Body ground Always 10 kΩ or higher
W1-5 (DI) or B76-56 (GLDI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE GLOW PLUG CONTROLLER

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>1AD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61
HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE ECM
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the glow plug controller connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W1-4 (+B) - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
W1-4 (+B) or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT EFI-MAIN NO. 2 RELAY

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.INSPECT EFI-MAIN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)

NG

16.REPLACE EFI-MAIN NO. 2 RELAY
12.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) Always Below 1 Ω
1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.CHECK CHARGING SYSTEM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.CHECK CHARGING SYSTEM
a.

Check the charging system and perform repairs as necessary.

Click herePower Source / Network>1AD-FTV BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPLACE EFI-MAIN NO. 2 RELAY
a.

Replace the EFI-MAIN NO. 2 relay.


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>1AD-FTV STARTING>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Using the GTS, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END