The ECM controls the internal fuel pressure of the common rail assembly by opening and closing the pressure discharge valve. When sudden deceleration occurs, the internal fuel pressure will temporarily become higher than usual and combustion noise may result. Therefore the ECM will open the valve temporarily to discharge the excess pressure inside the common rail assembly. Also, the pressure discharge valve opens when the ignition switch is turned off to allow prompt discharge of the common rail assembly internal pressure and so that the engine stops smoothly.
For more information on the pressure discharge valve and common rail system.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION
For more information on the injector driver (EDU).
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION
If P1271 and/or P1272 is present, refer to the DTC chart for the fuel system.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1271 | Fuel Regulator Circuit Malfunction (EDU Drive) | When either condition below is met (1 trip detection logic):
·
Open or short in pressure discharge valve circuit. ·
There is no valve opening confirmation (IJf) signal from the EDU to the ECM for a specific number of times consecutively, despite the ECM sending valve opening command (PRD) signals after the engine is started. |
·
Open or short in pressure discharge valve circuit ·
Pressure discharge valve (built into common rail assembly) ·
Injector driver (EDU) |
Comes on | DTC stored |
| P1272 | Fuel Pressure Regulator Malfunction | Pressure discharge valve does not open.
Actual pressure decreasing rate deviates from the simulated pressure decreasing rate after the ignition switch is turned off (2 trip detection logic). |
·
Open or short in pressure discharge valve circuit (P1271 is set simultaneously) ·
Pressure discharge valve (built into common rail assembly) ·
Injector driver (EDU) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P1271 | ·
Fuel Press ·
Target Common Rail Pressure ·
Pressure Discharge Valve |
| P1272 |
After confirming DTC P1271 and/or P1272, check the fuel pressure inside the common rail in "Powertrain / Engine and ECT / Data List / All Data / Fuel Press" using the GTS.
P1271:
After clearing the DTC, drive the vehicle at 50 km/h (31 mph) in third gear, and then decelerate by releasing the accelerator pedal. Check that P1271 is not present.
P1272:
After clearing the DTC, start and stop the engine twice (wait 30 seconds or more after turning the ignition switch off before starting the engine the second time), and then confirm that P1272 is not stored.
| Engine Speed | Fuel Pressure (kPa) |
|---|---|
| Idling | Fuel Press is within +/-5000 kPa of Target Common Rail Pressure |
| 2500 rpm (No engine load) |
| Condition | Fuel Press (Idling) | Fuel Press (1 Second after Engine Stopped) |
|---|---|---|
| Pressure discharge valve normal | 35000 kPa | 170 kPa |
| Open in pressure discharge valve circuit | 34000 kPa | 34300 kPa |
This DTC will be set if there is no valve opening confirmation (IJf) signal sent from the injector driver (EDU) to the ECM, despite the ECM has commanded the injector driver (EDU) to open the pressure discharge valve. This DTC refers to an open or short circuit malfunction of the pressure discharge valve circuit, not a malfunction in which a valve is stuck open or closed.
The injector driver (EDU) monitors the current supplied to the pressure discharge valve to verify that the current flows into the valve. If the current exceeds the specified level, the injector driver (EDU) interprets this as the IJf signal being low. If this DTC is stored, the ECM enters the fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.
The pressure discharge valve will open and discharge the internal fuel pressure from the common rail assembly to the fuel tank when the ignition switch is turned off. In this event, the ECM compares the actual drop rate of the internal fuel pressure and the target drop rate. If the ECM judges that the actual drop rate is smaller than the target, the ECM then judges that the valve is stuck closed and stores this DTC. This DTC will be stored if the internal fuel pressure does not drop to the target after the ignition switch has been turned off.
If this DTC is stored, the ECM enters fail-safe mode and limits engine power. The fail-safe mode continues until the ignition switch is turned off.
| Required sensors | Injector driver (EDU) |
| Frequency of operation | Continuous |
| Duration | 3 seconds |
| MIL operation | 1 driving cycle |
| Required sensors | Fuel pressure sensor |
| Frequency of operation | Once per driving cycle |
| Duration | 1 second |
| MIL operation | 2 driving cycles |
| Specification |
|---|
| The vehicle is driven at 50 km/h (31 mph) in 3rd gear, and then decelerated by complete release of the accelerator pedal 3 times. |
| Item | Specification | |
|---|---|---|
| Minimum | Minimum | |
| Fuel pressure | 30000 kPa (306 kgf/cm2, 4350 psi) | - |
| Fuel temperature | 0°C (32°F) | - |
| Battery voltage | 11 V | - |
| The monitor will not run if the fuel pressure sensor, pressure discharge valve circuit or fuel temperature sensor is malfunctioning. | ||
| Specification |
|---|
| There are no confirmation signals from the injector driver (EDU) for a specific number of times consecutively, despite the ECM sending command signals regularly during deceleration. |
| Specification |
|---|
| The internal pressure stays beyond the specified level after the ignition switch is turned off. |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P1271 | Ignition switch ON to off and drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by releasing the accelerator pedal |
| P1272 | Ignition switch ON to off |
Refer to DTC P0201 for injector driver (EDU) power source circuit.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>P0201
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
After completing repairs, confirm that P1271 and/or P1272 does not recur.
If P062D and P1271 are present simultaneously, there is an open in the INJF wire harness between the injector driver (EDU) and ECM, or there is an open in the wire harness for both an injector and the pressure discharge valve.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and turn the GTS on.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTC P1272 is output | A |
| DTC P1271 is output | B |
| DTC P1271 and P1272 are output | |
| Other DTCs are output | C |
A
B
C
Check the pressure discharge valve operation.
Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the common rail assembly.
Click hereEngine / Hybrid System>1AD-FTV FUEL>COMMON RAIL>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the pressure discharge valve connector.
Disconnect the injector driver (EDU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B69-1 - B54-1 (RLF+) | Always | Below 1 Ω |
| B69-2 - B54-2 (RLF-) | Always | Below 1 Ω |
| B69-1 or B54-1 (RLF+) - Body ground | Always | 10 kΩ or higher |
| B69-2 or B54-2 (RLF-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the injector driver (EDU) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B53-5 (PRD) - B76-52 (PRD) | Always | Below 1 Ω |
| B53-1 (RLF) - B76-123 (RLFF) | Always | Below 1 Ω |
| B53-5 (PRD) or B76-52 (PRD) - Body ground | Always | 10 kΩ or higher |
| B53-1 (RLF) or B76-123 (RLFF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Injector Driver (EDU)) |
Disconnect the injector driver (EDU) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B51-2 (+B) - B51-4 (GND) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the injector driver (EDU).
Click hereEngine / Hybrid System>1AD-FTV FUEL>INJECTOR DRIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and turn the GTS on.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P1271 and P1272.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | DTC P1271 and/or P1272 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Go to injector circuit.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>Injector Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the common rail assembly.
Click hereEngine / Hybrid System>1AD-FTV FUEL>COMMON RAIL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and turn the GTS on.
Drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal. Perform this 3 times.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the pending DTC is not output.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P1271 and P1272.
Check the DTC judgment result.
If STATUS is INCOMPLETE or N/A, perform the following procedure 3 times: drive the vehicle at 50 km/h (31 mph) in 3rd gear, and then decelerate by completely releasing the accelerator pedal.
| Proceed to |
|---|
| NEXT |
NEXT