Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P2084  Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2  P242B  Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3  


DESCRIPTION

Refer to DTC P0545.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>P0545

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2084 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 Both of the conditions are met (2 trip detection logic):
(a) The battery voltage is 8 V or higher.
(b) After the engine is stopped and the vehicle is left as is for 10 hours or more, the difference between "Exhaust Temperature B1S2" and "Coolant Temp" is 400°C (752°F) or higher when the ignition switch is turned to ON.
·

No. 2 exhaust gas temperature sensor (B1S2)

·

Engine coolant temperature sensor

·

ECM (soak timer)


Comes on DTC stored
P242B Exhaust Gas Temperature Sensor Circuit Range / Performance Bank 1 Sensor 3 Both of the conditions are met (2 trip detection logic):
(a) The battery voltage is 8 V or higher.
(b) After the engine is stopped and the vehicle is left as is for 10 hours or more, the difference between "Exhaust Temperature B1S3" and "Coolant Temp" is 400°C (752°F) or higher when the ignition switch is turned to ON.
·

No. 3 exhaust gas temperature sensor (B1S3)

·

Engine coolant temperature sensor

·

ECM (soak timer)


Comes on DTC stored

Related Data List
DTC No. Data List
P2084
·

Exhaust Temperature B1S2

·

Exhaust Temperature B1S3

·

Coolant temp

·

Intake Air


P242B

HINT:

If DTC P2084 and/or P242B is stored, the following symptoms may appear:

·

White smoke




MONITOR DESCRIPTION

The ECM compares the values from exhaust temperature sensors B1S2 and B1S3 with the engine coolant temperature when the ignition switch is turned to ON after the vehicle has been left soaking for 10 hours or more. If the difference is 400°C (752°F) or higher, a DTC indicating an exhaust gas temperature sensor malfunction is stored and the MIL is illuminated (2 trip detection logic).

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2084 Stop the engine, leave the vehicle as is for 1 to 2 hours and confirm that "Exhaust Temperature B1S2" is approximately the same value as "Intake Air".
P242B Stop the engine, leave the vehicle as is for 1 to 2 hours and confirm that "Exhaust Temperature B1S3" is approximately the same value as "Intake Air".

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Sensor 2 represents the sensor located upstream of the DPF catalytic converter.

·

Sensor 3 represents the sensor located downstream of the DPF catalytic converter.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2084 AND P242B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
DTC P2084 and/or P242B is output A
DTC P2084 and/or P242B and other DTCs are output B


HINT:

If any DTCs other than DTC P2084 or P242B are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (EXHAUST TEMPERATURE B1S2 AND B1S3)

B

2.READ VALUE USING GTS (EXHAUST TEMPERATURE B1S2 AND B1S3)
a.

Leave the vehicle as is for 1 to 2 hours with the engine stopped.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
Exhaust Temperature B1S3
50003 61 1062,1063

e.

Read the values.

Result:
Result Proceed to
Value of "Exhaust Temperature B1S2" is 400°C (752°F) or higher A
Value of "Exhaust Temperature B1S3" is 400°C (752°F) or higher B
Except above C


HINT:

If the exhaust gas temperature sensor is normal, the exhaust gas temperature drops when the vehicle is left as is for 1 to 2 hours with the engine stopped. If the exhaust gas temperature does not drop, the exhaust gas temperature sensor may be malfunctioning.




A

3.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR (B1S2)

B

4.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR (B1S3)

C

5.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
3.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR (B1S2)
a.

Replace the No. 2 exhaust gas temperature sensor (B1S2).

Click hereEngine / Hybrid System>1AD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR (B1S3)
a.

Replace the No. 3 exhaust gas temperature sensor (B1S3).

Click hereEngine / Hybrid System>1AD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Allow the engine to soak for 1 to 2 hours.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

e.

Read the value.

OK:

The difference between the displayed value and ambient temperature is below 5°C (9°F).


NOTICE:

If the difference between "Coolant Temp" and the ambient temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

7.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
8.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Leave the vehicle as is for 1 to 2 hours with the engine stopped.

HINT:
·

It is not necessary to allow the engine to soak if the engine is cold.

·

The engine cools faster if the hood is opened.




b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Exhaust Temperature B1S2, Exhaust Temperature B1S3 and Intake Air.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
Exhaust Temperature B1S3
Intake Air
50003 61 1062,1063,318

e.

Read the value.

OK:

The values of "Exhaust Temperature B1S2" and "Exhaust Temperature B1S3" are both approximately the same as "Intake Air".



Result:
Proceed to
NEXT



NEXT

END