Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P20CD  Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit  


DESCRIPTION

A268071
1.24,1.271 1.771,0.25 1.771,0.25 1.906,0.25 true 2.979,2.313 3.354,1.677 3.354,1.677 3.5,1.677 true 3.094,2.708 3.375,2.313 3.375,2.313 3.448,2.313 false 2.521,2.896 2.094,3.26 2.094,3.26 2,3.26 false 2.365,3.792 0.906,4.24 0.906,4.24 0.906,4.344 false 2.969,3.354 3.354,3.771 3.354,3.771 3.469,3.771 false 1.688,2.458 2.427,2.698 0.74,0.24 10 *2 0.448,1.396 1.302,1.594 0.854,0.198 10 *a 1.958,0.208 4.99,0.458 3.031,0.25 10 *1 3.552,1.594 5.875,1.99 2.323,0.396 10 *5 3.521,2.229 3.969,2.625 0.448,0.396 10 *6 3.531,3.688 6.031,4.073 2.5,0.385 10 *7 6.49,2.667 6.844,2.875 0.354,0.208 10 *8 1.844,3.198 2.646,3.448 0.802,0.25 10 *3 0.865,4.406 2.24,4.594 1.375,0.188 10 *4
*1 Exhaust Fuel Addition Injector Assembly *2 Turbocharger Sub-assembly
*3 DPF Catalytic Converter *4 Air Fuel Ratio Sensor
*5 Exhaust Gas Temperature Sensor (B1S1) *6 No. 2 Exhaust Gas Temperature Sensor (B1S2)
*7 No. 3 Exhaust Gas Temperature Sensor (B1S3) *8 ECM
*a Exhaust Gas - -


The exhaust fuel addition injector assembly is mounted on the outlet of the turbocharger sub-assembly, and low pressure fuel is supplied to the exhaust fuel addition injector assembly by the feed pump in the supply pump assembly. The exhaust fuel addition injector assembly adds fuel by a control signal from the ECM.

This injector is used for two different controls: PM forced regeneration and PM reduction.

During PM forced regeneration, the exhaust fuel addition injector assembly adds fuel to raise the catalyst temperature.

In the other control, the exhaust fuel addition injector assembly helps the air fuel ratio become rich. As a result, PM in the exhaust gas will be reduced in response to the rich air fuel ratio.

HINT:
·

For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION

·

If DTC P20CD is present, refer to the DTC table for Diesel Particulate Filter System.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit With the exhaust fuel addition injector assembly off, the FIVO output is high for 3 seconds (1 trip detection logic).
·

Open or short in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on DTC stored

HINT:

DTC P200C, P200E, P20CF and/or P2428 will be present if there is an open malfunction in the exhaust fuel addition injector assembly circuit.


MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector assembly, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVO) signals. The FIV signal is sent from the CPU to the exhaust fuel addition injector assembly via a drive circuit inside the ECM. The FIVO signal, which is originally output current from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVO signal, the ECM judges that the current has been applied to the exhaust fuel addition injector assembly.

This DTC will be set if the ECM judges that the number of signals of the FIV and FIVO are inconsistent.

A265674
2.667,3.208 3.01,3.385 0.344,0.177 10 ECM 1.229,0.906 1.573,1.125 0.344,0.219 10 CPU 1.417,1.583 1.813,1.74 0.396,0.156 10 FIVO 1.521,2.469 1.771,2.625 0.25,0.156 10 FIV 3.219,1.469 4.25,1.646 1.031,0.177 10 Monitor Circuit 3.188,2.344 4.292,2.521 1.104,0.177 10 Command Circuit 5.458,1.063 7.01,1.74 1.552,0.677 10 to Exhaust Fuel Addition Injector Assembly

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20CD Ignition switch ON for 3 seconds

WIRING DIAGRAM

A284163
3.073,1.469 5.75,1.698 2.677,0.229 10 false Exhaust Fuel Addition Injector Assembly 5.75,1.031 6.448,1.333 0.698,0.302 10 false FIV 1.281,0.906 1.552,1.125 0.271,0.219 10 false 5 0.604,2.344 1.823,2.542 1.219,0.198 10 false EFI-MAIN NO. 2 1.219,1.719 2.438,1.917 1.219,0.198 10 false EFI-MAIN NO. 2 5.406,1.031 5.771,1.25 0.365,0.219 10 false B76 5.417,2.146 5.781,2.365 0.365,0.219 10 false A61 5.448,0.844 5.813,1.063 0.365,0.219 10 false 105 5.458,1.969 5.823,2.188 0.365,0.219 10 false 45 5.74,2.042 6.438,2.344 0.698,0.302 10 false MREL 2.604,0.844 3.385,1.031 0.781,0.188 10 false EFI NO. 1 1.281,1.417 1.552,1.635 0.271,0.219 10 false 2 2.115,1.417 2.385,1.635 0.271,0.219 10 false 1 2.125,0.927 2.396,1.146 0.271,0.219 10 false 3 4.719,0.896 4.99,1.115 0.271,0.219 10 false 1 3.719,0.896 3.99,1.115 0.271,0.219 10 false 2 3.188,1.281 3.5,1.438 0.313,0.156 10 false B55 0.552,3.031 1.771,3.229 1.219,0.198 10 false FL MAIN 6.125,3.885 6.542,4.406 0.417,0.521 10 false ECM 0.781,3.74 2,3.938 1.219,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1AD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EXHAUST FUEL ADDITION INJECTOR ASSEMBLY)

NG

12.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EXHAUST FUEL ADDITION INJECTOR ASSEMBLY)
a.
A204917
0.417,1.042 0.813,1.302 0.396,0.26 0.396,0.25 0.615,0.438 0.219,0.188 10 *a 0.458,1.083 0.823,1.229 0.365,0.146 10 B55
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


Disconnect the exhaust fuel addition injector assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B55-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B55-1 - B76-105 (FIV) Always Below 1 Ω
B55-1 or B76-105 (FIV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B55-2 - 3 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
B55-2 or 3 (EFI-MAIN NO. 2 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT EFI-MAIN NO. 2 RELAY

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.INSPECT EFI-MAIN NO. 2 RELAY
a.

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)

NG

10.REPLACE EFI-MAIN NO. 2 RELAY
7.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - ECM)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 2 relay) - A61-45 (MREL) Always Below 1 Ω
1 (EFI-MAIN NO. 2 relay) or A61-45 (MREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 2 RELAY - BATTERY)
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE EFI-MAIN NO. 2 RELAY
a.

Replace the EFI-MAIN NO. 2 relay.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1AD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON for 3 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END