Home › Engine / Hybrid System › 1AD-FTV ENGINE CONTROL › ECD SYSTEM › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008729 1AD-FTV ENGINE CONTROL _0058550 ECD SYSTEM C

1AD-FTV ENGINE CONTROL  ECD SYSTEM  P2141  Diesel Throttle Motor Circuit Low  P2142  Diesel Throttle Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2141 Diesel Throttle Motor Circuit Low The throttle actuator current is below 0.5 A for 2.0 seconds during EGR valve operation (1 trip detection logic).
·

Open or short in throttle actuator circuit

·

Diesel throttle valve assembly

·

ECM


Comes on DTC stored
P2142 Diesel Throttle Motor Circuit High An throttle actuator current of 8 A or higher due to a mechanical malfunction, or a hall IC temperature of 150 to 160°C (302 to 320°F) or higher is detected (1 trip detection logic).
·

Open or short in throttle actuator circuit

·

Diesel throttle valve assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2141 Throttle Motor DUTY
P2142

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2141 Idle the engine for 5 seconds or more
P2142

WIRING DIAGRAM

A112572
1.083,1.135 1.302,1.313 0.219,0.177 10 false M+ 1.469,1.135 1.583,1.313 0.115,0.177 10 false 2 1.469,1.854 1.583,2.031 0.115,0.177 10 false 1 1.104,1.885 1.49,2.229 0.385,0.344 10 false M- 2.677,2.573 3.24,2.75 0.563,0.177 10 false Shielded 4.917,1.125 5.135,1.302 0.219,0.177 10 false M+ 4.594,1.125 4.813,1.302 0.219,0.177 10 false 42 4.594,1.875 4.813,2.052 0.219,0.177 10 false 43 4.594,2.625 4.813,2.802 0.219,0.177 10 false 82 4.917,1.865 5.354,2.219 0.438,0.354 10 false M- 4.917,2.74 5.292,2.917 0.375,0.177 10 false GE01 5.354,1.208 6.469,1.552 1.115,0.344 10 false Throttle Actuator Control Circuit 0.073,2.677 2.198,3.042 2.125,0.365 10 false Throttle Actuator (Built into Diesel Throttle Body Assembly) 5.729,3.448 6.073,3.625 0.344,0.177 10 false ECM 5.729,3.313 6.01,3.469 0.281,0.156 10 false B76 0.073,2.51 0.281,2.677 0.208,0.167 10 false B3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT DIESEL THROTTLE BODY ASSEMBLY
a.

Inspect the diesel throttle body assembly.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - DIESEL THROTTLE BODY ASSEMBLY)

NG

6.REPLACE DIESEL THROTTLE BODY ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (ECM - DIESEL THROTTLE BODY ASSEMBLY)
a.

Disconnect the diesel throttle body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B3-2 (M+) - B76-42 (M+) Always Below 1 Ω
B3-1 (M-) - B76-43 (M-) Always Below 1 Ω
B3-2 (M+) or B76-42 (M+) - Body ground Always 10 kΩ or higher
B3-1 (M-) or B76-43 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for 30 seconds.


f.

Start the engine.


g.

Idle the engine for 5 seconds or more.


h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Confirm that the DTC is not output.

Powertrain > Engine > Trouble Codes
50001 61

Result:
Proceed to
NEXT



NEXT

END

6.REPLACE DIESEL THROTTLE BODY ASSEMBLY
a.

Replace the diesel throttle body assembly.

Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED