If DTC P2237, P2238 and/or P2239 is present, refer to the DTC table for DPF system.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>SYSTEM DESCRIPTION
Refer to DTC P0031.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>P0031
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2237 | Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) | When either of the following conditions is met (1 trip detection logic):
·
Air fuel ratio sensor circuit malfunction ·
The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more. |
Main trouble area: Open in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
Air fuel ratio sensor heater ·
Air fuel ratio sensor heater circuit ·
ECM |
Comes on | DTC stored |
| P2238 | Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) | Air fuel ratio sensor circuit low (sensor 1) (1 trip detection logic). | Main trouble area: Open in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
Air fuel ratio sensor heater ·
Air fuel ratio sensor heater circuit ·
ECM |
Comes on | DTC stored |
| P2239 | Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) | Air fuel ratio sensor circuit high (sensor 1) (1 trip detection logic). | Main trouble area: Short in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
Air fuel ratio sensor heater ·
Air fuel ratio sensor heater circuit ·
ECM |
Comes on | DTC stored |
| P2252 | Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) | Air fuel ratio sensor circuit low (sensor 1) (1 trip detection logic). | Main trouble area: Open in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
Air fuel ratio sensor heater ·
Air fuel ratio sensor heater circuit ·
ECM |
Comes on | DTC stored |
| P2253 | Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) | Air fuel ratio sensor circuit high (sensor 1) (1 trip detection logic). | Main trouble area: Short in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
Air fuel ratio sensor heater ·
Air fuel ratio sensor heater circuit ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P2237 | ·
AFS Voltage B1S1 ·
Exhaust Temperature B1S1 |
| P2238 | |
| P2239 | |
| P2252 | |
| P2253 |
The air fuel ratio sensor outputs a voltage in proportion to the air fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2237 | Ignition switch ON for 7 seconds |
| P2238 | |
| P2239 | |
| P2252 | |
| P2253 |
Refer to DTC P0031.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>P0031
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B8-3 (AF2+) - B76-125 (AF2+) | Always | Below 1 Ω |
| B8-4 (AF2-) - B76-126 (AF2-) | Always | Below 1 Ω |
| B8-3 (AF2+) or B76-125 (AF2+) - Body ground | Always | 10 kΩ or higher |
| B8-4 (AF2-) or B76-126 (AF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT