The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated when the ignition switch is turned ON. The MIL goes off when the engine is started.
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1AD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).
Check that the Malfunction Indicator Lamp (MIL) illuminates when turning the ignition switch to ON.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and GTS on.
Check the communication between the GTS and ECM.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the diesel throttle body assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the electric EGR control valve assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the differential pressure sensor assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the camshaft position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the oil pressure sender gauge assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the nozzle vane position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the diesel throttle body assembly connector.
Disconnect the fuel pressure sensor connector.
Disconnect the electric EGR control valve assembly connector.
Disconnect the differential pressure sensor assembly connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the camshaft position sensor connector.
Disconnect the oil pressure sender gauge assembly connector.
Disconnect the nozzle vane position sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A61-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A61-57 (VCP2) - Body ground | Always | 10 kΩ or higher |
| B76-97 (VCVL) - Body ground | Always | 10 kΩ or higher |
| B76-68 (VCM) - Body ground | Always | 10 kΩ or higher |
| B76-69 (VCS) - Body ground | Always | 10 kΩ or higher |
| B76-94 (VCEG) - Body ground | Always | 10 kΩ or higher |
| B76-75 (VCPM) - Body ground | Always | 10 kΩ or higher |
| B76-78 (VCG) - Body ground | Always | 10 kΩ or higher |
| B76-93 (VPOP) - Body ground | Always | 10 kΩ or higher |
| B76-101 (VNVC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG