Home › Engine / Hybrid System › 2AD-FHV ENGINE CONTROL › ECD SYSTEM
RM3090E _51 Engine / Hybrid System _008730 2AD-FHV ENGINE CONTROL _0049704 ECD SYSTEM J

2AD-FHV ENGINE CONTROL  ECD SYSTEM  Engine Difficult to Start or Stalling  


DESCRIPTION

Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter Assembly
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List MAF
HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter assembly.



Intake System
Main fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbo and intake manifold


Data List MAP

Turbocharger System
Symptom and Corresponding Main Fault
·

Air leak in the turbocharged air passage

·

ECM not operating well

·

Turbocharger sub-assembly (turbine, bearing)


Symptoms Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped)
Data List MAP
·

With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.

·

Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.



Exhaust System
Main fault Blockage
Symptoms Lack of power (high engine speed, under heavy load)

Glow System
Main fault Glow system malfunction
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug assembly

Battery
Main fault Battery is depleted
Symptoms Difficult to start (cannot crank, crank speed is low), horn is quiet
Data List Battery Voltage
When cranking, battery voltage is below 5 V.

Engine - 1
Main fault Damaged, seized up
Symptoms Cannot crank, crank speed is low, strange noise

Engine - 2
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.



Start System
Main fault Starter system malfunction
Symptoms Difficult to start
Data List Starter Signal
·

Ignition switch (STA) output:

ON: Starter is operating

OFF: Starter is not operating




b.

Common Rail (ALL)

Supply Pump Assembly
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Fuel Filter Element Assembly
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



Pressure Discharge Valve
Main fault Does not completely close
Symptoms Difficult to start, engine stall, rough idle, lack of power

Injector Driver (EDU)
Main fault Circuit fault: The injector assembly does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as injector assembly
Diagnostic Trouble Code When the injector driver (EDU) has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Slowly raise the engine speed from idling to 3000 rpm with the vehicle stopped and check that Fuel Press and Common Rail Pres Sens 2 follow Target Common Rail Pressure. If the fuel pressure sensor malfunctions, the actual fuel pressure may deviate from the target fuel pressure (either Fuel Press or Common Rail Pres Sens 2 decreases to a value less than Target Common Rail Pressure).


Diagnostic Trouble Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close completely


Symptoms
·

Rough idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, lack of power (if there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt).


Data List Actual EGR Valve Pos., Target EGR Position
·

Generally, Actual EGR Valve Pos. = Target EGR Position +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is turned to ON (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.


EGR Close Lrn. Val., EGR Close Lrn. Status
·

When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V.

·

In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List Actual Throttle Position
·

0%: Fully open

·

100%: Fully closed

·

When the ignition switch ON (the engine is stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Starting Trouble


·

MAP

·

MAF

·

Intake Air

·

Coolant Temp

·

Battery Voltage

·

Starter Signal

·

Engine Speed of Cyl #1 (to #4)

·

Target Common Rail Pressure

·

Fuel Press

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position

·

Target EGR Position

·

Actual EGR Valve Pos.

·

EGR Close Lrn. Status

·

EGR Close Lrn. Val.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

Explanation of Symptom


Starting Trouble For good starting it is essential to have:
·

Sufficient cranking speed.

·

Properly operating engine preheating system.

·

Good quality fuel.


The fuel is ignited by the heat which is generated by compression pressure.
With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is poor due to leakage, the compression pressure will not rise and there will be difficulty starting.
When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air.
Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the injector assembly is open.


Trouble Area Chart According to Problem Cause


A299141E02
0.75,5.635 3.5,5.833 2.75,0.198 10 Difficult to start (cranking is OK) 0.875,0.958 3.625,1.156 2.75,0.198 10 Does not crank at all 3.594,0.958 6.344,1.156 2.75,0.198 10 Depleted battery 3.573,1.74 6.198,2.167 2.625,0.427 10 ECM power supply circuit malfunction 3.594,2.521 6.385,2.99 2.792,0.469 10 Clutch start switch assembly malfunction 3.552,3.188 5.875,3.677 2.323,0.49 10 Immobiliser system or entry and start system fault 3.594,4.104 5.917,4.594 2.323,0.49 10 Depleted battery 0.792,4.156 3.115,4.646 2.323,0.49 10 Cranking speed too slow 3.594,4.948 6.313,5.479 2.719,0.531 10 Increased internal friction of the engine mechanical parts (oil too thick, seizure, etc.) 4.135,7.313 6.458,7.802 2.323,0.49 10 Supply pump assembly malfunction 1.667,6.542 4.417,6.74 2.75,0.198 10 Fuel pressure is low 4.115,6.542 7.083,6.74 2.969,0.198 10 Fuel is not supplied to supply pump assembly 4.146,8.094 6.469,8.583 2.323,0.49 10 Common rail assembly malfunction 0.271,0.156 3.021,0.354 2.75,0.198 10 Difficult to start

A183464E11
0.833,0.146 1.094,0.427 0.26,0.281 10 A 4.188,0.76 6.677,0.99 2.49,0.229 10 Injector driver (EDU) circuit malfunction 1.771,0.781 3.438,1.01 1.667,0.229 10 Fuel pressure is high 4.177,1.531 5.792,1.76 1.615,0.229 10 Air in injector assembly 4.198,2.375 6.156,2.594 1.958,0.219 10 Injector assembly malfunction 1.771,2.365 3.406,2.625 1.635,0.26 10 Specific cylinder fault 4.188,3.125 6.188,3.333 2,0.208 10 Low compression pressure 4.188,3.979 6.083,4.219 1.896,0.24 10 Glow system malfunction 1.76,3.979 3.521,4.188 1.76,0.208 10 Difficult to start when cold 4.177,4.75 6.354,5.135 2.177,0.385 10 Engine coolant temperature sensor malfunction 1.76,6.115 3.094,6.344 1.333,0.229 10 Poor fuel quality

NOTICE:
·

After replacing the suction control valve, the ECM needs initialization.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION

·

After replacing an injector assembly, the ECM needs registration.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION



HINT:

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle age. Do not assume the vehicle is normal when the Data List outputs standard values. There may be concealed factors of the malfunction.



PROCEDURE

1.CHECK ENGINE CRANKING CONDITION
a.

Check the engine cranking condition.

Result:
Result Proceed to
Cranking is OK. A
Low cranking speed.
HINT:

When cranking speed is low, especially when the temperature is low, check if the engine oil grade matches the recommendation.


B
Does not crank at all. C




A

2.READ ALL OUTPUT DTCS

B

C

34.READ OUTPUT DTC (RELATED TO ENGINE)
2.READ ALL OUTPUT DTCS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: System Select / Health Check.


d.

Check the DTCs.

Result:
Proceed to
DTC is not output
Engine related DTCs are output


HINT:

If only DTC P1604 is output, proceed to step 3.




DTC is not output

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)

Engine related DTCs are output

3.TAKE SNAPSHOT DURING STARTING AND IDLING (PROCEDURE 3)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data.


d.

Take a snapshot when idling with no load after the engine is warmed up and when starting trouble is occurring.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the illustration below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

When there is trouble starting with a cold engine, take the snapshot when the engine is cold. Then warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and after idling the vehicle for 1 minute (A/C off, electrical load off), take a snapshot of the data for 15 seconds while idling.

·

Take a snapshot when the problem is occurring, such as when the engine is cold. However, if the problem does not reoccur, it is acceptable to only take a snapshot after the engine is warmed up and when the engine is started.




Result:
Proceed to
NEXT



NEXT

4.CHECK SNAPSHOT (FUEL PRESS)
4.CHECK SNAPSHOT (FUEL PRESS)
a.

Check Fuel Press in the snapshot taken in procedure 3 when the engine was started.

A227761E05
2.385,0.844 2.469,0.844 2.469,0.844 2.417,1.188 false 2.813,0.542 2.74,0.594 false 4.146,0.583 4.021,0.583 4.021,0.583 3.802,0.771 false 4.01,2.344 3.917,2.344 3.917,2.344 3.802,2.229 false 3.938,2.875 3.865,2.875 3.865,2.875 3.792,2.792 false 5.563,0.406 5.406,0.406 5.406,0.406 5.094,0.927 false 5.667,1.469 5.573,1.469 5.573,1.469 5.417,1.24 false 5.594,2.177 5.479,2.177 5.479,2.177 5.25,1.51 false 1.938,2.333 2.083,2.333 2.083,2.333 2.281,2.99 false 5.292,2.646 5.479,2.177 false 0.229,1.719 1.01,2 0.781,0.281 10 Fuel Press 3.969,2.792 4.104,2.969 0.135,0.177 10 a 2.844,0.469 2.99,0.646 0.146,0.177 10 b 4.198,0.5 4.365,0.667 0.167,0.167 10 d 4.052,2.271 4.198,2.448 0.146,0.177 10 c 1.073,0.771 2.344,1.135 1.271,0.365 10 Target Common Rail Pressure 5.646,0.333 7.042,0.583 1.396,0.25 10 Abnormal Fuel Press 1.115,2.25 2.01,2.667 0.896,0.417 10 Engine cranking start 2.469,3.198 3.573,3.375 1.104,0.177 10 About 2 seconds 5.656,2.104 7.156,2.323 1.5,0.219 10 Abnormal Fuel Press 5.75,1.417 7.031,1.646 1.281,0.229 10 Normal Fuel Press

Result:
Result Proceed to
At the point in the illustration labeled "a", Fuel Press is less than 10000 kPa from the value of Fuel Press when cranking started A
At the point in the illustration labeled "c", Fuel Press is below Target Common Rail Pressure by 15000 kPa or higher B
Fuel Press increases to a value that is higher than Target Common Rail Pressure immediately after cranking, and, at the point in the illustration labeled "d", Fuel Press is higher than Target Common Rail Pressure C
Except above D


HINT:
·

Even if Fuel Press is temporarily higher than Target Common Rail Pressure, as shown at the point in the illustration labeled "b", the supply pump assembly is normal.

·

Fuel Press is about 25000 to 35000 kPa when the engine is cranking and the engine coolant temperature is 0°C (32°F) or higher.

·

Fuel Press increases rapidly during cranking.





A

5.CHECK IF FUEL IS BEING SUPPLIED TO SUPPLY PUMP ASSEMBLY

B

14.READ VALUE USING GTS (FUEL PRESS)

C

18.INSPECT INJECTOR DRIVER (EDU)

D

20.INSPECT INJECTOR ASSEMBLY (CHECKING FOR PRESENCE OF AIR)
5.CHECK IF FUEL IS BEING SUPPLIED TO SUPPLY PUMP ASSEMBLY
a.

Disconnect the inlet hose from the supply pump assembly.


b.

Operate the priming pump and check that fuel is being supplied to the supply pump assembly.

OK:

Fuel is properly supplied to the supply pump assembly when the priming pump is operated.


HINT:
·

When there is a lack of fuel, fuel pressure drops.

·

Inspect for fuel filter element assembly clogging (check that the fuel filter element assembly is not clogged).




Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

12.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - SUPPLY PUMP ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-1 - B76-41 (PCV+) Always Below 1 Ω
B48-2 - B76-81 (PCV-) Always Below 1 Ω
B48-1 or B76-41 (PCV+) - Body ground Always 10 kΩ or higher
B48-2 or B76-81 (PCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE SUCTION CONTROL VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve.

Click hereEngine / Hybrid System>2AD-FHV FUEL>SUCTION CONTROL VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

9.PERFORM SUPPLY PUMP INITIALIZATION
9.PERFORM SUPPLY PUMP INITIALIZATION
a.

Perform supply pump initialization.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

10.READ VALUE USING GTS (FUEL PRESS)
10.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.

Powertrain > Engine > Data List
Tester Display
Fuel Press
50003 61 54

d.

Start the engine.


e.

Read the Fuel Press values while cranking and idling the engine.

Result:
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Press is below 20000 kPa 2 seconds after the starter signal changes from off to on B
Except above A




A

END

B

11.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
11.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug assembly for all the cylinders.

Click hereEngine / Hybrid System>2AD-FHV STARTING>GLOW PLUG>REMOVAL


b.

Visually check if there is fuel on the glow plug assemblies.

HINT:
·

If there is fuel on a glow plug assembly, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug assembly, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.




Result:
Proceed to
NEXT



NEXT

25.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
12.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - SUPPLY PUMP ASSEMBLY)
a.

Check and repair or replace the clogged fuel pipe.


Result:
Proceed to
NEXT



NEXT

13.BLEED AIR FROM FUEL SYSTEM
13.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.READ VALUE USING GTS (FUEL PRESS)
a.

Check Fuel Press in the snapshot taken in procedure 3 when the engine was warmed up.

Result:
Result Proceed to
Difference between Fuel Press and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or higher A
Except above B




A

15.REPLACE SUCTION CONTROL VALVE

B

17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
15.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve.

Click hereEngine / Hybrid System>2AD-FHV FUEL>SUCTION CONTROL VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.PERFORM SUPPLY PUMP INITIALIZATION
16.PERFORM SUPPLY PUMP INITIALIZATION
a.

Perform supply pump initialization.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
17.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

26.REPLACE FUEL FILTER ELEMENT ASSEMBLY
18.INSPECT INJECTOR DRIVER (EDU)
a.

Even in cases where DTC P062D is not stored even though the engine cannot be started, perform the DTC P062D (No. 1 Fuel Injector Driver Circuit Performance) troubleshooting procedure (Click here Engine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>P0201).

When troubleshooting the injector driver (EDU) system, the source of the malfunction is likely to be in one of the following areas, so be sure to inspect these areas carefully.

·

Injector driver (EDU) system power source circuit

·

Injector assembly circuit

·

Injector driver (EDU)

·

ECM


HINT:
·

When the engine cannot be started due to a malfunction in the injector driver (EDU) system, once the DTCs are cleared, the system cannot store DTC P062D even if it is confirmed that the engine cannot be started when trying to reproduce the problem symptoms.

As DTC P062D cannot be stored when starting the engine, fuel injection signals are output by the ECM, but fuel is not actually injected. Therefore, an excessive amount of fuel is supplied to the common rail by the fuel supply pump assembly, and as a result, the fuel pressure is higher than the target common rail pressure in the data recorded at the time the engine was having trouble starting.

·

If the problem cannot be determined even after performing the DTC P062D (No. 1 Fuel Injector Driver Circuit Performance) troubleshooting procedure and the fuel pressure is higher than the target common rail pressure when attempting to start the engine, proceed to the next step.

·

Perform the troubleshooting procedure for DTC P062D and proceed to the diagnostic flow situations where the engine does not start.



Result:
Proceed to
Injector driver (EDU) system is normal
Injector driver (EDU) system is abnormal




Injector driver (EDU) system is normal

19.INSPECT INJECTOR ASSEMBLY (CHECKING FOR PRESENCE OF AIR)

Injector driver (EDU) system is abnormal

REPAIR OR REPLACE MALFUNCTIONING PARTS

19.INSPECT INJECTOR ASSEMBLY (CHECKING FOR PRESENCE OF AIR)
a.

When the engine does not start, perform the following procedure.

i.

Stop the engine and leave the vehicle for 4 hours or more.

HINT:

It is necessary to leave the vehicle for 4 hours or more to wait for air in the injector assembly to come out.



ii.

Confirm the engine starts.



b.

When the engine starts, perform the following procedure.

i.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


ii.

Confirm the engine starts.



Result:
Proceed to
NEXT



NEXT

38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.INSPECT INJECTOR ASSEMBLY (CHECKING FOR PRESENCE OF AIR)
a.

When the engine does not start, perform the following procedure.

i.

Stop the engine and leave the vehicle for 4 hours or more.

HINT:

It is necessary to leave the vehicle for 4 hours or more to wait for air in the injector assembly to come out.



ii.

Check that the engine starts.

OK:

The engine starts.




b.

When the engine starts, perform the following procedure.

i.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


ii.

Check that the engine starts.

OK:

The engine starts.




Result:
Proceed to
OK
NG



OK

END

NG

21.CHECK DATA LIST
21.CHECK DATA LIST
a.

Check Injection Feedback Val # in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Injection Feedback Val #1 to #4 are 3 mm3/st or less.
Injection Volume is more than 12 mm3/st.
A
*
Injection Feedback Val for at least one cylinder is more than 3 mm3/st
HINT:

There may be a malfunction in the corresponding cylinder.


B
Except above C


HINT:
·

*: When this case occurs, usually symptoms may be noticeable, such as difficulty starting, lack of power.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.





A

22.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

23.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)

C

30.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
22.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

26.REPLACE FUEL FILTER ELEMENT ASSEMBLY
23.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Compression / Engine Speed of Cyl #1 to #4.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
50004 61 111 492,493,494,495

d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other. B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm higher than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

24.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER

B

25.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
24.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

25.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

25.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
HINT:

It can be determined that the injector assembly is faulty as the corresponding cylinder is malfunctioning, but has no compression loss.


a.

Replace the injector assembly.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

26.REPLACE FUEL FILTER ELEMENT ASSEMBLY
26.REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL FILTER>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

27.BLEED AIR FROM FUEL SYSTEM
27.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FHV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

28.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
28.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


b.

Perform the injector quantity learning.

Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECD SYSTEM>REGISTRATION


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

30.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS
a.

Check the temperature when starting trouble occurs.

Result:
Proceed to
Difficult to start only for cold engine.
Difficult to start both for cold and warmed up engine.




Difficult to start only for cold engine.

31.READ VALUE USING GTS (COOLANT TEMP)

Difficult to start both for cold and warmed up engine.

33.CHECK FUEL QUALITY
31.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

d.

Read the value displayed on the GTS.

OK:

Coolant Temp is not high when the engine is cold, and not low after the engine is warmed up.



Result:
Proceed to
OK
NG



OK

32.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

32.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

Result:
Proceed to
OK
NG



OK

33.CHECK FUEL QUALITY

NG

REPLACE GLOW PLUG ASSEMBLY

33.CHECK FUEL QUALITY
a.

Check that only diesel fuel is being used.


b.

Check that the fuel does not contain any impurities.


Result:
Proceed to
NEXT



NEXT

38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
34.READ OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Proceed to
DTC is not output
Engine related DTCs are output




DTC is not output

35.CHECK COMMUNICATION BETWEEN GTS AND ECM

Engine related DTCs are output

35.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check if the normal starting screen appears (check whether communication with the ECM is possible).

HINT:

Use a GTS that is able to communicate with other vehicles.


OK:

Communication is possible (vehicle can be recognized).



Result:
Proceed to
OK
NG



OK

36.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL)

NG

36.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / All Data / Neutral Position SW Signal.

Powertrain > Engine > Data List
Tester Display
Neutral Position SW Signal
50003 61 190

d.

Read the value displayed on the GTS.

OK:
GTS Display Condition Specified Condition
Neutral Position SW Signal Shift lever in neutral ON



Result:
Proceed to
OK
NG



OK

37.CHECK STARTING SYSTEM

NG

INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

37.CHECK STARTING SYSTEM
a.

Inspect the starting system.

HINT:

Be sure to inspect the following areas:

·

Starter (ST) relay

·

Starter assembly

·

Immobiliser system




Result:
Proceed to
NEXT



NEXT

38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
38.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END