Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) L

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  PRECAUTION  


IGNITION SWITCH EXPRESSION


HINT:

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



INITIALIZATION AND REGISTRATION


NOTICE:

When replacing the ECM and/or any other components in the following chart, perform the corresponding utility items.


HINT:

When the ECM and other component(s) are replaced at the same time, perform the following utility items by following the instructions shown on the GTS display, starting with the ECM.

Replacement Part Utility Item
ECM
·

Learning Values Save (Click here (Click here))

·

Learning Values Write (Click here (Click here))


Engine assembly
·

Clear Crank Time Compensation Data (Click here (Click here))

·

Input Injector Compensation Code (Click here (Click here))

·

Pilot Quantity Learning (Click here (Click here))


No. 1 crankshaft position sensor plate Clear Crank Time Compensation Data (Click here (Click here))
Supply pump assembly
Suction control valve
Supply Pump Initialization (Click here (Click here))
Injector assembly
·

Input Injector Compensation Code (Click here (Click here))

·

After that perform the Pilot Quantity Learning (Click here (Click here))




HINT:

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initializations/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.



INJECTOR COMPENSATION CODE


HINT:
·

Each injector has different fuel injection characteristics. In order to optimize fuel injection performance, the ECM compensates for these differences by adjusting the fuel injection duration of each injector according to its compensation code. Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector.

·

If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



a.
A203986
1.49,2.573 2.583,2.083 false 0.167,0.125 0.479,0.323 0.313,0.198 10 *a 1.292,2.521 1.604,2.719 0.313,0.198 10 *1
*1 Fuel Injector Compensation Code
*a Example


When an injector is replaced, the injector compensation code must be input into the ECM (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION).


b.

When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION).



PILOT QUANTITY LEARNING


HINT:
·

By performing "Pilot Quantity Learning", the injection volume for each cylinder is precisely adjusted so that the engine runs smoothly. The "Pilot Quantity Learning" information is stored in the EEPROM of the ECM.

·

If an incorrect pilot quantity learning value is input into the ECM, the engine may rattle or engine idling may become rough.



a.

When an injector is replaced, the injector compensation code must to input to the ECM and then perform the pilot quantity learning (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION).


b.

When the ECM is replaced, all of the existing injector pilot quantity learning values must be input into the new ECM (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION).



DIFFICULT TO START ENGINE, ENGINE STALLING, BLACK SMOKE EMITTED ROUGH IDLING, EXCESSIVE ENGINE VIBRATION, ENGINE KNOCKING, LACK OF POWER OR HESITATION


a.

Check if the customer problem is described below. If so, refer to the appropriate troubleshooting section.

i.

Engine is difficult to start or stalls.


ii.

Black smoke is emitted.


iii.

Rough Idling or Excessive Engine Vibrations.


iv.

Engine Knocking or Rattling.


v.

Lack of Power or Hesitation.




WHEN USING GTS


CAUTION:

Observe the following items for safety reasons:

·

Read its instruction books before using the GTS.

·

Prevent the GTS cable from being caught on the pedals, shift lever and steering wheel when driving with the GTS connected to the vehicle.

·

When driving the vehicle for testing purposes using the GTS, two persons are required. One drives the vehicle and the other operates the GTS.