Home › Engine / Hybrid System › 2AD-FTV ENGINE CONTROL › ECD SYSTEM(for CCo)
RM3090E _51 Engine / Hybrid System _008377 2AD-FTV ENGINE CONTROL _0049703 ECD SYSTEM(for CCo) C

2AD-FTV ENGINE CONTROL  ECD SYSTEM(for CCo)  P1229  Fuel Pump System  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1229 Fuel Pump System The actual fuel pressure exceeds the target fuel pressure by 5000 kPa or higher for 30 seconds.
(1 trip detection logic)
·

Short in suction control valve circuit

·

Suction control valve

·

Fuel pressure sensor (common rail assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P1229
·

Fuel Press

·

Target Common Rail Pressure

·

Injection Pressure Correction

·

Target Pump SCV Current

·

Pump SCV Learning Value



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>SYSTEM DESCRIPTION).

·

When DTC P1229 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure.

Under a stable condition such as idling after warm up the engine, Fuel Press is within +/- 5000 kPa of Target Common Rail Pressure when normal.

·

When there is a problem with the movement of the fuel supply pump assembly (when Fuel Press is higher than Target Common Rail Pressure due to a problem in which the suction valve has difficulty closing), the values of Injection Pressure Correction and Target Pump SCV Current decrease.



MONITOR DESCRIPTION

P1229 (Fuel over-feed):

The ECM stores this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P1229 Idling for 60 seconds

WIRING DIAGRAM

A205135E01
2.063,1.396 2.26,1.573 0.198,0.177 10 2 5.427,0.698 5.698,0.875 0.271,0.177 10 41 5.427,1.375 5.698,1.552 0.271,0.177 10 81 5.708,1.281 6.125,1.458 0.417,0.177 10 PCV- 5.99,2.021 6.385,2.198 0.396,0.177 10 ECM 5.708,0.625 6.125,0.802 0.417,0.177 10 PCV+ 2.073,0.729 2.271,0.906 0.198,0.177 10 1 0.646,2.031 2.042,2.219 1.396,0.188 10 Suction Control Valve 5.99,1.833 6.26,1.99 0.271,0.156 10 B76 0.667,1.854 0.969,2.031 0.302,0.177 10 B48

CAUTION / NOTICE / HINT

NOTICE:
·
·

After replacing the fuel supply pump, the ECM needs initialization (Click here Engine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>INITIALIZATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When this DTC is stored, be sure to carefully examine "Fuel Press", "Target Common Rail Pressure", "Target Pump SCV Current", and "Pump SCV Learning Value" in the freeze frame data.



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
Except above A
DTC P1229 and "P0190, P0192 and/or P0193" are output B




A

2.READ VALUE USING GTS (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)

B

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

2.READ VALUE USING GTS (FUEL PRESS AND TARGET COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.

Powertrain > Engine > Data List
Tester Display
Target Common Rail Pressure
Fuel Press
50003 61 706,54

e.

Check that the internal fuel pressure of the common rail is within the specification below.

OK:

Fuel Press is within 5000 kPa of Target Common Rail Pressure when engine is idling after warm up the engine.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
3.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B48-1 - B76-41 (PCV+) Always Below 1 Ω
B48-2 - B76-81 (PCV-) Always Below 1 Ω
B48-1 or B76-41 (PCV+) - Body ground Always 10 kΩ or higher
B48-2 or B76-81 (PCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE FUEL FILTER ELEMENT ASSEMBLY

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
5.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
50004 61 90 706,54

d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


Result:
Result Proceed to
Except above A
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa. B




A

6.REPLACE FUEL FILTER ELEMENT ASSEMBLY

B

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE FUEL FILTER ELEMENT ASSEMBLY
a.

Replace the fuel filter element assembly.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL FILTER>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

7.REPLACE SUCTION CONTROL VALVE
7.REPLACE SUCTION CONTROL VALVE
a.

Replace the Replace the suction control valve.

Click hereEngine / Hybrid System>2AD-FTV FUEL>SUCTION CONTROL VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>2AD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

9.PERFORM SUPPLY PUMP INITIALIZATION
9.PERFORM SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off for 30 seconds or more.


f.

Start the engine.


g.

Idle the engine for 60 seconds, and then run it at 2500 rpm without load for 60 seconds.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

i.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P1229.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END