Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM(w/ Canister Pump Module) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008378 2AR-FE ENGINE CONTROL _0060196 SFI SYSTEM(w/ Canister Pump Module) C

2AR-FE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0505  Idle Control System Malfunction  


DESCRIPTION

The idle speed is controlled by the ETCS (Electronic Throttle Control System). The ETCS is comprised of: 1) the one valve type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the throttle position sensor, which detects the opening angle of the throttle valve; 4) the accelerator pedal position sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the ETCS. Based on the target idle speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0505 Idle Control System Malfunction Idle speed continues to vary greatly from the target idle speed (2 trip detection logic).
·

Electronic throttle control system

·

Intake system

·

PCV hose connections

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the idle speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if either of the following conditions is met:

·

The difference between the target engine idle speed and actual engine idle speed exceeds the threshold and the IAC flow rate learned value is stuck at the upper or lower limit for 5 seconds or more.

·

After driving at a vehicle speed of 10 km/h (6.25 mph) or more, the difference between the target and actual engine idle speed exceeds the threshold 5 times or more during a driving cycle, and then the system determines that the IAC flow rate learned value is stuck at the upper or lower limit, or that the IAC flow rate learned value has been changed by an amount that exceeds the threshold.

A283590E02
0.74,0.958 1.5,1.198 0.76,0.24 10 Idle Speed 3.99,0.969 5.5,1.198 1.51,0.229 10 Learned Idle Air Volume 2.177,1.76 3.094,1.99 0.917,0.229 10 Target Speed 2.177,2.958 3.344,3.177 1.167,0.219 10 Actual Idle Speed 3.25,3.5 3.667,3.75 0.417,0.25 10 Time 6.344,3.625 6.76,3.875 0.417,0.25 10 Time 6.302,2.865 6.917,3.073 0.615,0.208 10 Minimum 6.25,1.333 6.917,1.573 0.667,0.24 10 Maximum 4.292,1.552 4.75,1.823 0.458,0.271 10 Large 4.563,2.344 4.729,2.594 0.167,0.25 10 0 4.281,3.083 4.75,3.333 0.469,0.25 10 Small


MONITOR STRATEGY

Required Sensors/Components (Main) Electronic throttle control system
Required Sensors/Components (Related) Crankshaft position sensor
Engine coolant temperature sensor
Vehicle speed sensor
Frequency of Operation Once per driving cycle
MIL Operation 2 driving cycles

TYPICAL MALFUNCTION THRESHOLDS

Either of the following conditions is met 1 or 2
1. Both of the following conditions A and B met -
A. Engine speed - Target engine speed Less than -100 rpm, or higher than 150 rpm (A/C off and NSW off)
Less than -100 rpm, or higher than 200 rpm (A/C on or NSW on)
B. IAC flow rate learned value 0.9 L/sec. or less, or 6 L/sec. or more for 5 seconds or more
2. Both of the following conditions C and D met -
C. Frequency that both of following conditions (a) and (b) met 5 times or more
(a) Engine speed - Target engine speed Less than -100 rpm, or higher than 150 rpm (A/C off and NSW off)
Less than -100 rpm, or higher than 200 rpm (A/C on or NSW on)
(b) Vehicle condition Stopped after being driven at 10 km/h (6.25 mph) or more
D. Either of the following conditions is met (c) or (d)
(c) IAC flow rate learned value 0.9 L/sec. or less, or 6 L/sec. or more
(d) Amount of change of IAC flow rate learned value +2.56 L/sec. or more, or -2.56 L/sec. or less

CONFIRMATION DRIVING PATTERN

A231468E26
4.552,2.958 4.875,3.375 4.875,3.375 3.979,2.958 false 5.74,2.958 5.104,3.344 5.104,3.344 5.125,2.958 false 2.833,2.969 2.615,3.24 false 3.188,2.958 2.573,3.521 false 1.292,1.208 1.885,1.406 0.594,0.198 10 10 km/h 1.427,2.031 1.865,2.26 0.438,0.229 10 Idling 0.646,2.385 1.854,2.75 1.208,0.365 10 Ignition Switch ON 2.344,2.531 2.542,2.719 0.198,0.188 10 [A] 2.74,2.24 2.958,2.396 0.219,0.156 10 [B] 6.292,3.313 6.51,3.49 0.219,0.177 10 [F] 2.313,3.521 3.563,3.677 1.25,0.156 10 5 minutes or more 4.604,3.385 5.906,3.542 1.302,0.156 10 20 seconds or more 3.615,0.979 3.865,1.177 0.25,0.198 10 [E] 5.927,0.958 6.177,1.156 0.25,0.198 10 [E] 5.354,0.969 5.604,1.167 0.25,0.198 10 [E] 4.771,0.969 5.021,1.167 0.25,0.198 10 [E] 4.198,0.979 4.448,1.177 0.25,0.198 10 [E] 3.104,2.24 3.323,2.417 0.219,0.177 10 [C] 1.833,3.146 2.625,3.313 0.792,0.167 10 Warming up 3.323,3.313 3.542,3.49 0.219,0.177 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].

7.

Idle the engine for 5 minutes or more [C].

HINT:

In order to keep the idling stable, turn off the A/C and all other electric loads and do not perform any shift operations.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0505.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].



13.

Accelerate the vehicle to 10 km/h (6.25 mph) or more, and then idle the engine for 20 seconds or more [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Repeat step [E] 5 times.

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P0505.

19.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

The following conditions may also cause DTC P0505 to be stored:

1.

The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.

2.

The accelerator pedal being not fully released.


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Engine Speed, ISC Feedback Value and ISC Learning Value].

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DATA LIST / ACTIVE TEST



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0505 is output A
DTC P0505 and other DTCs are output B


HINT:

If any DTCs other than P0505 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>2AR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM(w/ Canister Pump Module)>ON-VEHICLE INSPECTION

OK:

PCV valve and hose are connected correctly and are not damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2AR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from the intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
a.

Check the throttle with motor body assembly condition.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.


HINT:

Perform "Inspection After Repair" after replacing the throttle with motor body assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0505)

NG

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0505)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0505 is output A
DTC is not output B




A

B

END