| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0451 | Evaporative Emission Control System Pressure Sensor Range / Performance | Either of the following conditions is met:
·
Sensor output voltage fluctuates frequently in a certain time period. ·
Sensor output voltage does not vary in a certain time period. |
·
Canister pump module ·
Connector/wire harness (canister pump module - ECM) ·
EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose) ·
ECM |
Comes on | DTC stored |
| P0452 | Evaporative Emission Control System Pressure Sensor / Switch Low Input | EVAP pressure sensor less than 42.11 kPa(abs) [315.867 mmHg(abs)] for 0.5 seconds. | ·
Canister pump module ·
Connector/wire harness (canister pump module - ECM) ·
EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose) ·
ECM |
Comes on | DTC stored |
| P0453 | Evaporative Emission Control System Pressure Sensor / Switch High Input | EVAP pressure sensor higher than 123.761 kPa(abs) [928.331 mmHg(abs)] for 0.5 seconds. | ·
Canister pump module ·
Connector/wire harness (canister pump module - ECM) ·
EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose) ·
ECM |
Comes on | DTC stored |
| DTC No. | Monitoring Item | Detection Timing | Detection Logic |
|---|---|---|---|
| P0451 | Canister pressure sensor abnormal voltage fluctuation | ·
EVAP monitoring (ignition switch off) ·
Engine running |
2 trip |
| Canister pressure sensor constant voltage | ·
EVAP monitoring (ignition switch off) |
2 trip | |
| P0452 | Canister pressure sensor low input | ·
Ignition switch ON ·
EVAP monitoring (ignition switch off) |
1 trip |
| P0453 | Canister pressure sensor high input | ·
Ignition switch ON ·
EVAP monitoring (ignition switch off) |
1 trip |
The canister pressure sensor is built into the canister pump module.
The description can be found in EVAP (Evaporative Emission) System.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>EVAP System
DTC P0451: Canister pressure sensor abnormal voltage fluctuation or being constant
If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as the canister pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC.
Alternatively, if the sensor voltage output does not change for 2 minutes, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and stores the DTC.
(Both the malfunctions are detected by 2 trip detection logic).
DTC P0452: Canister pressure sensor voltage low
If the canister pressure sensor voltage output (pressure) is less than 0.45 V: 42.11 kPa(abs) [315.867 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).
DTC P0453: Canister pressure sensor voltage high
If the canister pressure sensor voltage output (pressure) is higher than 4.9 V: 123.761 kPa(abs) [928.331 mmHg(abs)], the ECM interprets this as an open or short circuit in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC (1 trip detection logic).
| Required Sensors/Components | Canister pump module |
| Frequency of Operation | Continuous |
The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by the GTS. It takes a maximum of approximately 24 minutes.
Do not perform the Evaporative System Check when the fuel tank is higher than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
Do not run the engine during this operation.
When the temperature of the fuel is 35°C (95°F) or higher, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Intake Air.
Check that the intake air temperature is between 4.4 and 35°C (40 and 95°F).
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0451, P0452 or P0453.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel tank cap.
The GTS is required to conduct the following diagnostic troubleshooting procedure.
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Enter the following menus: Powertrain / Engine and ECT / Data List / Ptrl Evaporative / Vapor Pressure Pump.
| Tester Display |
|---|
| Vapor Pressure Pump |
Read the EVAP (Evaporative Emission) pressure displayed on the GTS.
| Display (DTC Output) | Test Result | Suspected Trouble Area | Proceed to |
|---|---|---|---|
| P0451 | - | Canister pressure sensor | C |
| P0452 | Less than 42.11 kPa(abs) [315.867 mmHg(abs)] | ·
Wire harness/connector (ECM - canister pressure sensor) ·
Canister pressure sensor ·
Short in ECM circuit |
A |
| P0453 | Higher than 123.761 kPa(abs) [928.331 mmHg(abs)] | ·
Wire harness/connector (ECM - canister pressure sensor) ·
Canister pressure sensor ·
Open in ECM circuit |
B |
A
B
C
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>EVAP System
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
|---|---|---|---|---|
| A62-49 (PPMP) - Body ground | Always | Below 10 Ω | ·
Wire harness/connector (ECM - canister pressure sensor) ·
Short in canister pressure sensor circuit |
A |
| 10 kΩ or higher | ·
Wire harness/connector (ECM - canister pressure sensor) ·
Short in ECM circuit |
B |
A
B
Disconnect the canister pump module connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
|---|---|---|---|---|
| A62-49 (PPMP) - Body ground | Always | 10 kΩ or higher | Short in canister pressure sensor circuit | A |
| Below 10 Ω | Short in wire harness/connector (ECM - canister pressure sensor) | B |
A
B
Replace the charcoal canister leak detection pump sub-assembly.
Click hereEngine / Hybrid System>2AR-FE EMISSION CONTROL>CANISTER(w/ Canister Pump Module)>REMOVAL
When replacing the canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in the canister interior, replace the canister and canister pump module together.
Check for filter blockage in the canister. If the charcoal filter inside the canister is clogged, replace the canister and canister pump module together.
Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.
| *1 | Fuel Tank Vent Hose | *2 | Vent Hose |
| *3 | Air Inlet Port | *4 | Fuel Tank |
| *5 | Canister Pump Module | *6 | Canister Assembly |
| *7 | Fuel Tank Inlet Pipe Sub-assembly (Canister Filter) | *8 | Fuel Tank Cap Assembly |
| *a | Inspection Area
(check for disconnection and/or cracks) |
- | - |
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Perform the Evaporative System Check using the GTS, referring to the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0452 or P0453.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
| Proceed to |
|---|
| NEXT |
NEXT
If the exhaust pipe has been removed, go to the next step before reinstalling it.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Canister Pump Module) |
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V3-8 (SGND) - Body ground | Always | 100 Ω or less |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| V3-6 (VCC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| V3-7 (VOUT) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Test Result | Suspected Trouble Area | Proceed to |
|---|---|---|
| Voltage and resistance within standard ranges | Open in canister pressure sensor circuit | A |
| Voltage and/or resistance outside standard ranges | Open in wire harness/connector (ECM - canister pressure sensor) | B |
A
B