Home › Drivetrain › U760F AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE
RM3090E _52 Drivetrain _008753 U760F AUTOMATIC TRANSMISSION / TRANSAXLE _0051086 TRANSMISSION CONTROL CABLE A

U760F AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in neutral.


a.

Put the transmission control cable assembly into the cabin and connect the transmission control cable assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the transmission control cable assembly to the bracket with a new clip.


c.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


d.

Turn the nut of the transmission control cable assembly 180° counterclockwise. While holding the nut in place, push in the stopper until the stopper clicks twice.

C203379C02
1.563,0.552 1.438,0.167 1.438,0.167 1.354,0.167 false 1.542,1.146 1.667,1.521 1.667,1.521 1.75,1.521 false 1.198,0.094 1.365,0.271 0.167,0.177 10 *1 1.781,1.448 1.958,1.625 0.177,0.177 10 *2 3.656,0.146 3.823,0.344 0.167,0.198 10 *a
*1 Stopper *2 Nut
*a Push in - -


NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable assembly will not be reusable.


HINT:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.



e.

Connect the outer part of the transmission control cable assembly to the shift lever assembly. Check that the stopper returns to the pulled-out position.

C203380C02
1.25,0.302 1.313,0.125 1.313,0.125 1.385,0.125 true 1.177,0.885 1.063,1.229 1.063,1.229 0.99,1.229 true 1.302,1.271 1.208,1.531 1.208,1.531 1.125,1.531 true 1.417,0.063 1.594,0.24 0.177,0.177 10 *1 0.802,1.156 0.979,1.333 0.177,0.177 10 *2 0.969,1.458 1.146,1.635 0.177,0.177 10 *3
*1 Stopper *2 Nut
*3 Shift Lever Assembly - -



f.
C203381C11
1.813,1.01 1.677,0.479 1.677,0.479 1.573,0.479 true 1.844,2.229 1.76,1.917 1.76,1.917 1.667,1.917 false 2.448,2.094 2.365,1.792 2.365,1.792 2.469,1.792 false 2.344,1.135 2.427,1.448 2.427,1.448 2.521,1.448 false 1.354,0.385 1.531,0.552 0.177,0.167 10 *1 1.458,1.833 1.635,2 0.177,0.167 10 *1 2.49,1.698 2.698,1.885 0.208,0.188 10 *2 2.542,1.354 2.75,1.542 0.208,0.188 10 *2
*1 Slider
*2 Lock Piece


Slide the slider in the direction shown in the illustration and pull out the lock piece.


g.
C204586

Connect the end of the transmission control cable assembly to the shift lever assembly.

NOTICE:
·

Make sure that the lock piece is pulled up.

·

Push on the end of the transmission control cable assembly all the way to the base of the pin.




h.
C278980C01
0.781,0.531 0.677,0.146 0.677,0.146 0.563,0.146 true 0.396,0.073 0.708,0.271 0.313,0.198 10 *1 0.156,1.365 0.469,1.563 0.313,0.198 10 *a
*1 Adjuster Case
*a Push in


Push the lock piece into the adjuster case and lock it.

NOTICE:

Make sure that the lock piece is completely locked by the slider.



Hide 2.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 3.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 4.INSTALL AIR CLEANER CAP SUB-ASSEMBLY