The ECM determines the vehicle inclination based on a signal from the yaw rate and acceleration sensor (airbag sensor assembly)*1 or deceleration sensor*2.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1586 | Acceleration Sensor Malfunction | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The ignition switch is ON. 2.
With the vehicle speed at 30 km/h (18 mph) or more, the difference between the longitudinal acceleration calculated based on the G sensor value and the longitudinal acceleration calculated based on the vehicle speed exceeds 0.35 G for 60 seconds or more. 3.
3.0 seconds 4.
1 trip detection logic 1.
The ignition switch is ON. 2.
No change detected in the yaw rate and acceleration sensor*1 or deceleration sensor*2 signal 16 times or more while the vehicle speed decreases from 30 km/h (18 mph) to 0 km/h (0 mph). 3.
3.0 seconds 4.
1 trip detection logic |
·
Yaw rate and acceleration sensor (Airbag sensor assembly)*1 ·
Deceleration sensor*2 ·
Skid control ECU (Brake actuator assembly) ·
CAN communication system |
- | DTC stored |
*1: w/ VSC
*2: w/o VSC
Refer to DTC P1585.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P1585
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If a CAN communication DTC is output, perform troubleshooting for that DTC first.
Check for DTCs of the CAN communication system.
| Proceed to |
|---|
| DTCs are not output |
| DTCs are output |
DTCs are not output
DTCs are output
Clear the DTCs.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Write down the currently output DTCs before clearing them.
Perform a road test where the vehicle is driven at 30 km/h (18 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Proceed to |
|---|
| Only P1586 is output |
| P1586 and other DTCs are output |
If any other DTCs besides DTC P1586 are output, perform troubleshooting for those DTCs first.
Only P1586 is output
P1586 and other DTCs are output
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| G Sensor |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| G Sensor | Converted output voltage of deceleration sensor | min.: 0 V
max.: 79.998 V |
Displays converted voltage of deceleration sensor
·
Vehicle on level ground: 2.31 V to 2.69 V ·
Decelerating: 1.88 V to 2.5 V ·
Accelerating: 2.5 V to 3.11 V ·
G sensor malfunction: Set to 1.87 V ·
Communication malfunction: Set to 1.87 V |
- |
In accordance with the display on the GTS, read the Data List.
| Result | Proceed to |
|---|---|
| Data displayed is as specified under Normal Condition (w/ VSC) | A |
| Data displayed is as specified under Normal Condition (w/o VSC) | B |
| Data displayed is not as specified under Normal Condition (w/ VSC) | C |
| Data displayed is not as specified under Normal Condition (w/o VSC) | D |
A
B
C
D
Replace the skid control ECU (brake actuator assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o VSC)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the yaw rate and acceleration sensor (airbag sensor assembly).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the deceleration sensor.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>DECELERATION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT