The ECM detects the input shaft rotation speed based on the signal from the primary pulley speed sensor (transmission revolution sensor (NIN)) and performs gear ratio control.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2767 | Input / Turbine Speed Sensor "B" Circuit No Signal | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.
The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more and the vehicle speed is approx. 7 km/h (4.3 mph). 2.
The transmission revolution sensor (NIN) value is less than 300 rpm. 3.
2 seconds 4.
1 trip detection logic |
·
Open or short in transmission revolution sensor (NIN) circuit ·
Transmission revolution sensor (NIN) ·
ECM ·
Continuously variable transaxle assembly |
Comes on | DTC stored |
The ECM receives a signal from the primary pulley speed sensor (transmission revolution sensor (NIN)) installed in the continuously variable transaxle and determines the input shaft speed in order to control the gear ratio. If the ECM detects no signal from the primary pulley speed sensor even while the vehicle is moving, it will conclude that there is a malfunction in the primary pulley speed sensor. The ECM will illuminate the MIL and store the DTC.
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| SPD (NIN) |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| SPD (NIN) | Primary pulley speed (NIN) | min.: 0 rpm
max.: 12750 rpm |
·
Vehicle stopped: 0 rpm ·
Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed |
Data is displayed in increments of 50 rpm. |
In accordance with the display on the GTS, read the Data List.
| Proceed to |
|---|
| Data displayed is not as specified under Normal Condition |
| Data displayed is as specified under Normal Condition |
Data displayed is not as specified under Normal Condition
Data displayed is as specified under Normal Condition
| *a | Component without harness connected
(Transmission Revolution Sensor (NIN)) |
Disconnect the transmission revolution sensor (NIN) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (NIN-) - 2 (NIN+) | 20°C (68°F) | 560 to 680 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B75-127 (NIN+) - B75-128 (NIN-) | 20°C (68°F) | 560 to 680 Ω |
| B75-127 (NIN+) - Body ground | Always | 10 kΩ or higher |
| B75-128 (NIN-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Remove the transmission revolution sensor (NIN).
Check the sensor tip of the transmission revolution sensor (NIN).
The sensor tip of the transmission revolution sensor (NIN) is not damaged or contaminated.
If the sensor tip of the transmission revolution sensor (NIN) is damaged or contaminated with metal particles, the CVT belt may be damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the continuously variable transaxle assembly.
Click hereDrivetrain>K111 MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT