With the ignition switch off and the driver door closed, pressing the manual lock or unlock switch on the multiplex network master switch assembly while holding a seat memory switch (M1 switch or M2 switch) will register the transmitter recognition code into the seat memory switch that was pressed. After registration is completed, the answer back buzzer sounds.
The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING
When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.
Check the manual lock/unlock function by using the door control switch (power window regulator master switch assembly).
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Manual lock/unlock function operates normally.
| Proceed to |
|---|
| OK (w/ Entry and Start System) |
| OK (w/o Entry and Start System) |
| NG |
OK (w/ Entry and Start System)
OK (w/o Entry and Start System)
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check that the engine starts normally when the ignition switch is pressed with the brake pedal depressed and while carrying the key.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Store a seat position in memory.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check that the buzzer sounds for 0.5 seconds to indicate that a position has been stored.
The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.
If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
Seat position memory function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Restore a memorized seat position.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.
The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.
If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.
Seat position restoring function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Front door courtesy light switch assembly signal | ON or OFF | ON: Driver door open
OFF: Driver door closed |
- |
| Tester Display |
|---|
| FR Door Courtesy SW |
ON or OFF appears on the screen according to the driver door condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When the following conditions are met, press the manual lock or unlock switch on the power window regulator master switch assembly.
Ignition switch is off
M1 or M2 seat memory switch is pressed and held
Driver door closed
Key is being carried
Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Proceed to |
|---|
| Buzzer sounds normally |
| Buzzer does not sound normally |
Buzzer sounds normally
Buzzer does not sound normally
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mem SW No. w/KeyID1 | Memory switch linked with key ID1 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1 MEM SW2: M2 switch linked with key ID1 MEM SW3: M3 switch linked with key ID1* |
- |
| Mem SW No. w/KeyID2 | Memory switch linked with key ID2 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2 MEM SW2: M2 switch linked with key ID2 MEM SW3: M3 switch linked with key ID2* |
- |
| Mem SW No. w/KeyID3 | Memory switch linked with key ID3 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3 MEM SW2: M2 switch linked with key ID3 MEM SW3: M3 switch linked with key ID3* |
- |
| Mem SW No. w/KeyID4 | Memory switch linked with key ID4 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4 MEM SW2: M2 switch linked with key ID4 MEM SW3: M3 switch linked with key ID4* |
- |
| Mem SW No. w/KeyID5 | Memory switch linked with key ID5 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5 MEM SW2: M2 switch linked with key ID5 MEM SW3: M3 switch linked with key ID5* |
- |
| Mem SW No. w/KeyID6 | Memory switch linked with key ID6 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6 MEM SW2: M2 switch linked with key ID6 MEM SW3: M3 switch linked with key ID6* |
- |
| Mem SW No. w/KeyID7 | Memory switch linked with key ID7 | NONE, MEM SW1, MEM SW2, or MEM SW3* | NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7 MEM SW2: M2 switch linked with key ID7 MEM SW3: M3 switch linked with key ID7* |
- |
*: Although the item is displayed on the GTS, it is not applicable to this vehicle.
| Tester Display |
|---|
| Mem SW No. w/KeyID1 |
| Mem SW No. w/KeyID2 |
| Mem SW No. w/KeyID3 |
| Mem SW No. w/KeyID4 |
| Mem SW No. w/KeyID5 |
| Mem SW No. w/KeyID6 |
| Mem SW No. w/KeyID7 |
On the GTS display, it is confirmed that the memory call has been registered.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Close and lock all doors.
Unlock the driver door by pressing the unlock switch of the memory call registered key or touching the driver door outside handle while holding the memory call registered key.
Open the driver door and check that the driver seat moves to the memorized position.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Proceed to |
|---|
| Driver seat moves to the memorized position |
| Driver seat does not move to the memorized position |
Driver seat moves to the memorized position
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Driver seat does not move to the memorized position
Replace the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.
Ignition switch is off
M1 or M2 seat memory switch is pressed and held
Driver door closed
Key is being carried
Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Proceed to |
|---|
| Buzzer sounds normally |
| Buzzer does not sound normally |
Buzzer sounds normally
Buzzer does not sound normally
Check that the wireless door lock/unlock operates normally.
Wireless door lock/unlock operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the position control ECU and switch assembly.
Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
When the following conditions are met, press the manual lock or unlock switch on the multiplex network master switch assembly.
Ignition switch is off
M1 or M2 seat memory switch is pressed and held
Driver door closed
Key is being carried
Check that the buzzer sounds for 0.5 seconds to indicate the completion of memory call registration.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK
| Proceed to |
|---|
| Buzzer sounds normally |
| Buzzer does not sound normally |
Buzzer sounds normally
Buzzer does not sound normally