Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066372 AIRBAG SYSTEM(w/ Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ Occupant Classification System)  B1615/14  Front Airbag Sensor LH Malfunction  


DESCRIPTION

The front airbag sensor LH consists of a diagnostic circuit and frontal deceleration sensor, etc.

If the airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether the SRS should be activated.

DTC B1615/14 is stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1615/14 Front Airbag Sensor LH Malfunction Either condition is met:
·

A front airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Front airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

C279108E03
1.323,0.917 1.688,1.135 0.365,0.219 10 false +SL 1.365,2.083 1.698,2.281 0.333,0.198 10 false -SL 5.594,2.063 5.979,2.24 0.385,0.177 10 false -SL 5.563,0.896 5.958,1.094 0.396,0.198 10 false +SL 3.427,2.292 3.885,2.49 0.458,0.198 10 false -SL 5.531,3.01 7.083,3.24 1.552,0.229 10 false Airbag Sensor Assembly 5.573,2.833 6.031,3.031 0.458,0.198 10 false G92 0.354,2.854 0.708,3.052 0.354,0.198 10 false A24 1.688,1.969 1.917,2.156 0.229,0.188 10 false 1 3.583,1.833 3.844,1.99 0.26,0.156 10 false 2 3.563,0.688 3.792,0.844 0.229,0.156 10 false 1 1.688,0.813 1.917,1 0.229,0.188 10 false 2 3.406,0.917 3.865,1.115 0.458,0.198 10 false AG9 3.417,2.083 3.854,2.281 0.438,0.198 10 false AG9 3.417,1.115 3.875,1.313 0.458,0.198 10 false +SL 5.313,0.771 5.573,0.927 0.26,0.156 10 false 30 5.313,1.958 5.573,2.115 0.26,0.156 10 false 28 0.323,3.021 1.906,3.198 1.583,0.177 10 false Front Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK FRONT AIRBAG SENSOR LH
a.
C148689C20
0.617,1.104 0.787,1.265 0.17,0.161 10 *1 2.02,1.104 2.191,1.279 0.17,0.175 10 *2
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1615/14 is output
DTC B1610/13 is output
DTC B1610/13 and B1615/14 are not output


HINT:

Codes other than DTC B1610/13 and B1615/14 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


l.

Return the front airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B1615/14 is output

DTC B1610/13 is output

DTC B1610/13 and B1615/14 are not output