Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066372 AIRBAG SYSTEM(w/ Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ Occupant Classification System)  B1656/38  Seat Belt Buckle Switch LH Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the airbag sensor assembly and front seat inner belt assembly LH.

DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1656/38 Seat Belt Buckle Switch LH Circuit Malfunction
One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.

·

A front seat inner belt assembly LH malfunction.

·

An airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat inner belt assembly LH

·

Airbag sensor assembly



WIRING DIAGRAM

C253566E20
2.448,1.49 2.698,1.719 0.25,0.229 10 false 2 2.469,3.052 2.594,3.219 0.125,0.167 10 false 1 1.99,1.219 2.406,1.375 0.417,0.156 10 false LBE+ 2.031,2.792 2.427,2.938 0.396,0.146 10 false LBE- 5.854,1.365 6.26,1.531 0.406,0.167 10 false LBE+ 5.542,1.49 5.792,1.656 0.25,0.167 10 false 15 0.302,3.906 0.656,4.052 0.354,0.146 10 false N14 0.302,4.052 2.563,4.198 2.26,0.146 10 false Front Seat Inner Belt Assembly LH 5.563,3.854 5.906,4.01 0.344,0.156 10 false N21 5.563,4 7.125,4.198 1.563,0.198 10 false Airbag Sensor Assembly 5.563,3.063 5.813,3.229 0.25,0.167 10 false 23 5.844,2.938 6.25,3.104 0.406,0.167 10 false LBE-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

2.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.
C208245C08
0.313,1.75 0.625,1.906 0.313,0.156 10 *1 2.104,1.573 2.417,1.729 0.313,0.156 10 *2 1.521,1.042 1.833,1.198 0.313,0.156 10 *3
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly
*3 No. 2 Floor Wire


Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.


b.

Check that the connectors (on the airbag sensor assembly side and front seat inner belt assembly LH side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged
Connectors are deformed or damaged



Connectors are not deformed or damaged

3.CHECK NO. 2 FLOOR WIRE

Connectors are deformed or damaged

REPLACE NO. 2 FLOOR WIRE

3.CHECK NO. 2 FLOOR WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C253298C03
4.375,0.396 4.771,0.625 0.396,0.229 2.396,0.406 2.792,0.635 0.396,0.229 5.198,0.865 5.417,0.865 false 5.375,0.573 5.76,0.792 false 5.417,1.219 5.76,0.938 false 3.031,1.167 3.479,0.833 false 4.063,1.083 3.708,0.833 false 0.406,1.49 0.719,1.646 0.313,0.156 10 false *1 1.729,1.25 2.042,1.406 0.313,0.156 10 false *2 1.031,0.844 1.344,1 0.313,0.156 10 false *3 3.531,0.177 3.844,0.333 0.313,0.156 10 false *4 5.875,0.198 6.188,0.354 0.313,0.156 10 false *5 4.99,0.792 5.302,0.948 0.313,0.156 10 false *6 2.99,0.052 3.302,0.208 0.313,0.156 10 false *a 5.125,0.063 5.438,0.219 0.313,0.156 10 false *b 5.125,1.302 5.542,1.49 0.417,0.188 10 false LBE- 5.021,0.448 5.438,0.635 0.417,0.188 10 false LBE+ 4.438,0.427 4.854,0.615 0.417,0.188 10 false N21 2.469,0.438 2.885,0.625 0.417,0.188 10 false N14 2.875,1.219 3.292,1.406 0.417,0.188 10 false LBE- 3.958,1.177 4.375,1.365 0.417,0.188 10 false LBE+ 1.531,1.01 1.844,1.167 0.313,0.156 10 false A 1.219,1.26 1.531,1.417 0.313,0.156 10 false B 0.896,1.26 1.208,1.417 0.313,0.156 10 false C 0.552,1.042 0.865,1.198 0.313,0.156 10 false D
*1 Front Seat Inner Belt Assembly LH *2 Airbag Sensor Assembly
*3 No. 2 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N14-2 (LBE+) - Body ground Ignition switch ON Below 1 V
N14-1 (LBE-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 15 (LBE+) and 23 (LBE-) of connector B. NOTICE:

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-2 (LBE+) - N14-1 (LBE-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N14-2 (LBE+) - N14-1 (LBE-) Always 1 MΩ or higher
N14-2 (LBE+) - Body ground Always 1 MΩ or higher
N14-1 (LBE-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT SEAT INNER BELT ASSEMBLY LH

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK FRONT SEAT INNER BELT ASSEMBLY LH
a.
C171812C09
0.719,1.271 0.875,1.438 0.156,0.167 10 *1 1.844,1.125 2.031,1.292 0.188,0.167 10 *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly and front seat inner belt assembly LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188
Result:
Proceed to
DTC B1656/38 is not output
DTC B1656/38 is output



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.




DTC B1656/38 is not output

DTC B1656/38 is output

5.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
5.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt assembly LH.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL

HINT:

Perform the inspection using parts from a normal vehicle if possible.



Result:
Proceed to
NEXT



NEXT

6.CHECK AIRBAG SENSOR ASSEMBLY
6.CHECK AIRBAG SENSOR ASSEMBLY
a.
C171812C09
0.719,1.271 0.875,1.438 0.156,0.167 10 *1 1.844,1.125 2.031,1.292 0.188,0.167 10 *2
*1 Front Seat Inner Belt Assembly LH
*2 Airbag Sensor Assembly


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1656/38 is not output
DTC B1656/38 is output


HINT:

Codes other than DTC B1656/38 may be output at this time, but they are not related to this check.




DTC B1656/38 is not output

END (FRONT SEAT INNER BELT ASSEMBLY LH WAS DEFECTIVE)

DTC B1656/38 is output