Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/ Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0066372 AIRBAG SYSTEM(w/ Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ Occupant Classification System)  B1940/75  Short in Selectable Force Limiter Squib RH Circuit  B1941/75  Open in Selectable Force Limiter Squib RH Circuit  B1942/75  Short to GND in Selectable Force Limiter Squib RH Circuit  B1943/75  Short to +B in Selectable Force Limiter Squib RH Circuit  


DESCRIPTION

The selectable force limiter squib circuit consists of the airbag sensor assembly and front seat outer belt assembly RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the selectable force limiter squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1940/75 Short in Selectable Force Limiter Squib RH Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the selectable force limiter squib circuit during the primary check.

·

A selectable force limiter squib malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat outer belt assembly RH (Selectable force limiter Squib)

·

Airbag sensor assembly


B1941/75 Open in Selectable Force Limiter Squib RH Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the selectable force limiter squib circuit for 2 seconds.

·

A selectable force limiter squib malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat outer belt assembly RH (Selectable force limiter Squib)

·

Airbag sensor assembly


B1942/75 Short to GND in Selectable Force Limiter Squib RH Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the selectable force limiter squib circuit for 0.5 seconds.

·

A selectable force limiter squib malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat outer belt assembly RH (Selectable force limiter Squib)

·

Airbag sensor assembly


B1943/75 Short to +B in Selectable Force Limiter Squib RH Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the selectable force limiter squib circuit for 0.5 seconds.

·

A selectable force limiter squib malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat outer belt assembly RH (Selectable force limiter Squib)

·

Airbag sensor assembly



WIRING DIAGRAM

C253326E66
2.469,2.427 2.604,2.583 0.135,0.156 10 false 1 2.448,1.583 2.583,1.74 0.135,0.156 10 false 2 4.563,1.542 4.698,1.698 0.135,0.156 10 false 8 4.563,2.417 4.698,2.573 0.135,0.156 10 false 7 2.042,1.573 2.406,1.719 0.365,0.146 10 false SR+ 2.042,2.406 2.406,2.552 0.365,0.146 10 false SR- 4.75,1.656 5.167,1.833 0.417,0.177 10 false PR2+ 4.75,2.49 5.146,2.688 0.396,0.198 10 false PR2- 0.771,2.99 2.135,3.458 1.365,0.469 10 false M2 0.75,3.167 2.729,3.51 1.979,0.344 10 false Front Seat Outer Belt Assembly RH (Selectable Force Limiter) 4.656,4.156 5.042,4.313 0.385,0.156 10 false M25 4.635,4.333 6.719,4.521 2.083,0.188 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (SELECTABLE FORCE LIMITER SQUIB)
a.
C213957C07
0.448,2.156 0.844,2.427 0.396,0.271 2.063,2.292 2.448,2.51 false 0.781,0.198 0.969,0.375 0.188,0.177 10 false *1 1.865,1.271 2.042,1.448 0.177,0.177 10 false *2 1.573,1.573 1.76,1.75 0.188,0.177 10 false *a 2.521,2.469 2.875,2.656 0.354,0.188 10 false *4 2.25,1.896 2.427,2.073 0.177,0.177 10 false *3 0.521,2.208 0.75,2.375 0.229,0.167 10 false M2 1.781,0.385 1.906,0.563 0.125,0.177 10 false A 1.24,0.604 1.365,0.781 0.125,0.177 10 false C 1.01,0.604 1.135,0.781 0.125,0.177 10 false D
*1 Selectable Force Limiter Squib
*2 Airbag Sensor Assembly
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Selectable Force Limiter Squib)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat outer belt assembly RH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH (selectable force limiter squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1940/75, B1941/75, B1942/75 or B1943/75 is not output
DTC B1940/75, B1941/75, B1942/75 or B1943/75 is output


HINT:

Codes other than DTC B1940/75, B1941/75, B1942/75 or B1943/75 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.



DTC B1940/75, B1941/75, B1942/75 or B1943/75 is not output

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

DTC B1940/75, B1941/75, B1942/75 or B1943/75 is output

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208249C02
0.852,0.944 1.045,1.183 0.193,0.24 10 D 0.647,0.456 0.84,0.624 0.193,0.168 10 *1 1.252,0.448 1.446,0.615 0.193,0.168 10 *2 1.698,1.671 1.892,1.838 0.193,0.168 10 *3 1.084,0.944 1.296,1.165 0.212,0.221 10 C 1.497,0.944 1.709,1.174 0.212,0.23 10 B 1.902,0.651 2.095,0.835 0.193,0.184 10 A
*1 Selectable Force Limiter Squib
*2 Floor Wire
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front seat outer belt assembly RH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK SELECTABLE FORCE LIMITER SQUIB CIRCUIT

NG

REPLACE FLOOR WIRE

3.CHECK SELECTABLE FORCE LIMITER SQUIB CIRCUIT
a.
C213958C05
0.448,2.198 0.844,2.469 0.396,0.271 1.698,2.188 1.281,2.563 false 1.833,2.188 2.177,2.563 false 0.667,0.198 0.854,0.375 0.188,0.177 10 false *1 1.698,1.24 1.875,1.417 0.177,0.177 10 false *3 1.583,1.656 1.771,1.833 0.188,0.177 10 false *a 2.198,2 2.375,2.177 0.177,0.177 10 false *4 0.531,2.24 0.76,2.406 0.229,0.167 10 false M2 1.865,0.354 1.99,0.531 0.125,0.177 10 false A 1.042,0.625 1.167,0.802 0.125,0.177 10 false C 1.438,0.646 1.563,0.823 0.125,0.177 10 false B 0.854,0.635 0.979,0.813 0.125,0.177 10 false D 1.208,0.198 1.396,0.375 0.188,0.177 10 false *2 0.969,2.49 1.385,2.865 0.417,0.375 10 false SR+ 2.208,2.49 2.938,2.969 0.729,0.479 10 false SR-
*1 Selectable Force Limiter Squib
*2 Floor Wire
*3 Airbag Sensor Assembly
*4 Connector C
*5 Front view of wire harness connector
(to Selectable Force Limiter Squib)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-2 (SR+) - Body ground Ignition switch ON Below 1 V
M2-1 (SR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-2 (SR+) - M2-1 (SR-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-2 (SR+) - M2-1 (SR-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-2 (SR+) - Body ground Always 1 MΩ or higher
M2-1 (SR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG SENSOR ASSEMBLY

NG

REPLACE FLOOR WIRE

4.CHECK AIRBAG SENSOR ASSEMBLY
a.
C146259C10
0.76,0.229 0.99,0.385 0.229,0.156 10 false *1 1.906,1.313 2.083,1.49 0.177,0.177 10 false *2 1.01,0.667 1.146,0.833 0.135,0.167 10 false D 1.135,0.656 1.271,0.823 0.135,0.167 10 false C 1.656,0.427 1.885,0.583 0.229,0.156 10 false A
*1 Selectable Force Limiter Squib
*2 Airbag Sensor Assembly


Connect the connectors to the front seat outer belt assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1940/75, B1941/75, B1942/75 or B1943/75 is not output
DTC B1940/75, B1941/75, B1942/75 or B1943/75 is output


HINT:

Codes other than B1940/75, B1941/75, B1942/75 or B1943/75 may be output at this time, but they are not related to this check.




DTC B1940/75, B1941/75, B1942/75 or B1943/75 is not output

DTC B1940/75, B1941/75, B1942/75 or B1943/75 is output