The front seat cushion squib RH circuit consists of the airbag sensor assembly and the front seat airbag sub-assembly.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the front seat cushion squib RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1875/67 | Short in Passenger Side Front Seat Cushion Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly receives a line short circuit signal 5 times in the front seat cushion squib RH circuit during primary check. ·
A front seat cushion squib RH malfunction ·
An airbag sensor assembly malfunction |
·
Floor wire ·
Front seat airbag sub-assembly (Front seat cushion squib RH) ·
Airbag sensor assembly |
| B1876/67 | Open in Passenger Side Front Seat Cushion Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly receives an open circuit signal in the front seat cushion squib RH circuit for 2 seconds. ·
A front seat cushion squib RH malfunction ·
An airbag sensor assembly malfunction |
·
Floor wire ·
Front seat airbag sub-assembly (Front seat cushion squib RH) ·
Airbag sensor assembly |
| B1877/67 | Short to GND in Passenger Side Front Seat Cushion Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly receives a short circuit to ground signal in the front seat cushion squib RH circuit for 0.5 seconds. ·
A front seat cushion squib RH malfunction ·
An airbag sensor assembly malfunction |
·
Floor wire ·
Front seat airbag sub-assembly (Front seat cushion squib RH) ·
Airbag sensor assembly |
| B1878/67 | Short to B+ in Passenger Side Front Seat Cushion Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly receives a short circuit to B+ signal in the front seat cushion squib RH circuit for 0.5 seconds. ·
A front seat cushion squib RH malfunction ·
An airbag sensor assembly malfunction |
·
Floor wire ·
Front seat airbag sub-assembly (Front seat cushion squib RH) ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
To perform the simulation method, enter check mode (signal check) with the GTS (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>DIAGNOSTIC TROUBLE CODE CHART).
| *1 | Front Seat Cushion Squib RH |
| *2 | Airbag Sensor Assembly |
| *3 | Connector C |
| *4 | SST |
| *a | Front view of wire harness connector
(to Front Seat Cushion Squib RH) |
| *b | Color: Red |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the front seat airbag sub-assembly connectors.
Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.
Never connect the tester to the front seat airbag sub-assembly (front seat cushion squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
DTC B1875/67, B1876/67, B1877/67 or B1878/67 is not output.
Codes other than DTC B1875/67, B1876/67, B1877/67 or B1878/67 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag sensor assembly.
| *1 | Front Seat Cushion Squib RH |
| *2 | Floor Wire |
| *3 | Airbag Sensor Assembly |
Check that the connectors (on the airbag sensor assembly side and front seat airbag sub-assembly side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not damaged or deformed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag sensor assembly.
| *1 | Front Seat Cushion Squib RH |
| *2 | Airbag Sensor Assembly |
| *3 | Connector C |
| *a | Front view of wire harness connector
(to Front Seat Cushion Squib RH) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M15-1 (FCP-) - Body ground | Ignition switch ON | Below 1 V |
| M15-2 (FCP+) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M15-1 (FCP-) - M15-2 (FCP+) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M15-1 (FCP-) - M15-2 (FCP+) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M15-1 (FCP-) - Body ground | Always | 1 MΩ or higher |
| M15-2 (FCP+) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Seat Cushion Squib RH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the front seat airbag sub-assembly and the airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
DTC B1875/67, B1876/67, B1877/67 or B1878/67 is not output.
Codes other than DTC B1875/67, B1876/67, B1877/67 or B1878/67 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG