Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) › from 2013.11
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0103549 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  C1622  Open or Short Circuit in Back Camera Signal  


DESCRIPTION

This DTC is stored if the navigation receiver assembly*1 or radio and display receiver assembly*2 judges that the signals or signal lines between the navigation receiver assembly*1 or radio and display receiver assembly*2 and the television camera assembly are not normal as a result of its self check.

*1: for Navigation Receiver Type

*2: for Radio and Display Type


DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Open or Short Circuit in Back Camera Signal Open or short in the television camera assembly signal circuit
·

Harness or connector

·

Television camera assembly

·

Navigation receiver assembly (for Navigation Receiver Type)

·

Radio and display receiver assembly (for Radio and Display Type)



WIRING DIAGRAM

E288886E01
5.208,2.74 5.823,2.938 0.615,0.198 10 false U22 5.219,2.927 7.042,3.26 1.823,0.333 10 false Television Camera Assembly 0.26,2.76 0.875,2.958 0.615,0.198 10 false G158 0.271,2.927 2.177,3.167 1.906,0.24 10 false Navigation Receiver Assembly 1.365,1.458 1.635,1.656 0.271,0.198 10 false V+ 1.385,1.875 1.594,2.073 0.208,0.198 10 false V- 1.656,1.354 1.875,1.563 0.219,0.208 10 false 12 5.531,1.885 6.146,2.083 0.615,0.198 10 false CV- 1.667,1.771 1.896,1.99 0.229,0.219 10 false 24 5.531,1.469 6.146,1.667 0.615,0.198 10 false CV+ 5.354,1.344 5.49,1.542 0.135,0.198 10 false 3 5.354,1.781 5.49,1.979 0.135,0.198 10 false 2 0.083,0.052 2.521,0.333 2.438,0.281 12 false for Navigation Receiver Type: 1.271,1.031 1.573,1.25 0.302,0.219 10 false CA+ 1.135,2.302 1.615,2.51 0.479,0.208 10 false CGND 5.354,0.948 5.49,1.146 0.135,0.198 10 false 6 5.531,1.042 6.146,1.24 0.615,0.198 10 false CB+ 5.531,2.302 6.01,2.51 0.479,0.208 10 false CGND 1.656,2.208 1.885,2.427 0.229,0.219 10 false 23 1.656,0.938 1.875,1.146 0.219,0.208 10 false 11 5.354,2.208 5.49,2.406 0.135,0.198 10 false 5 4.5,2.448 4.635,2.646 0.135,0.198 10 false * 3.552,2.458 3.688,2.656 0.135,0.198 10 false * 2.583,2.469 2.719,2.667 0.135,0.198 10 false * 0.094,3.417 1.333,3.646 1.24,0.229 10 false *: Shielded

E288886E02
0.083,2.75 0.698,2.948 0.615,0.198 10 false G159 0.083,2.917 2.573,3.219 2.49,0.302 10 false Radio and Display Receiver Assembly 1.354,1.875 1.583,2.115 0.229,0.24 10 false V- 1.354,1.458 1.583,1.698 0.229,0.24 10 false V+ 1.646,1.344 1.875,1.583 0.229,0.24 10 false 12 1.656,1.76 1.885,2 0.229,0.24 10 false 24 5.354,1.792 5.51,1.99 0.156,0.198 10 false 2 5.354,1.365 5.51,1.563 0.156,0.198 10 false 3 5.563,1.469 5.927,1.677 0.365,0.208 10 false CV+ 5.563,1.896 5.927,2.104 0.365,0.208 10 false CV- 5.208,2.74 5.573,2.948 0.365,0.208 10 false U22 5.208,2.917 7.073,3.156 1.865,0.24 10 false Television Camera Assembly 0.073,0.063 2.563,0.365 2.49,0.302 12 false for Radio and Display Type: 1.656,2.208 1.885,2.448 0.229,0.24 10 false 23 1.146,2.302 1.594,2.521 0.448,0.219 10 false CGND 1.26,1.031 1.708,1.25 0.448,0.219 10 false CA+ 5.563,1.042 6.01,1.26 0.448,0.219 10 false CB+ 5.354,0.938 5.51,1.135 0.156,0.198 10 false 6 5.563,2.323 6.01,2.542 0.448,0.219 10 false CGND 5.354,2.198 5.51,2.396 0.156,0.198 10 false 5 4.51,2.438 4.688,2.635 0.177,0.198 10 false * 3.594,2.458 3.771,2.656 0.177,0.198 10 false * 2.583,2.458 2.76,2.656 0.177,0.198 10 false * 0.125,3.417 1.708,3.625 1.583,0.208 10 false *: Shielded 1.635,0.917 1.865,1.156 0.229,0.24 10 false 11

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>CALIBRATION


PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Proceed to
No DTC is output
DTC is output (for Navigation Receiver Type)
DTC is output (for Radio and Display Type)



No DTC is output

DTC is output (for Navigation Receiver Type)

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)

DTC is output (for Radio and Display Type)

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G158 navigation receiver assembly connector.


b.

Disconnect the U22 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G158-11 (CA+) - U22-6 (CB+) Always Below 1 Ω
G158-12 (V+) - U22-3 (CV+) Always Below 1 Ω
G158-24 (V-) - U22-2 (CV-) Always Below 1 Ω
G158-23 (CGND) - U22-5 (CGND) Always Below 1 Ω
G158-11 (CA+) - Body ground Always 10 kΩ or higher
G158-12 (V+) - Body ground Always 10 kΩ or higher
G158-24 (V-) - Body ground Always 10 kΩ or higher
G158-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E280624C10
1.458,0.323 2.01,0.583 0.552,0.26 1.094,1.031 0.813,0.729 0.813,0.729 0.469,0.729 true 1.094,1.271 1.021,1.927 1.021,1.927 0.75,1.927 true 0.927,1.24 0.792,1.667 0.792,1.667 0.552,1.667 true 1.552,0.354 2.167,0.552 0.615,0.198 10 false G158 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.135,0.635 0.521,0.833 0.385,0.198 10 false CA+ 0.281,1.844 0.771,2.052 0.49,0.208 10 false CGND 0.354,1.573 0.615,1.771 0.26,0.198 10 false V-
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G158-23 (CGND) - Body ground Always Below 1 Ω
G158-24 (V-) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G158-11 (CA+) - Body ground Ignition switch ON 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.CHECK TELEVISION CAMERA ASSEMBLY

NG

4.CHECK TELEVISION CAMERA ASSEMBLY
a.

Check the waveform of the television camera assembly using an oscilloscope.

E280623C05
1.25,0.531 1.75,0.802 0.5,0.271 3.146,2.292 3.344,2.292 3.344,2.292 3.5,1.792 false 3.885,2.281 3.729,2.281 3.729,2.281 3.594,1.729 false 6.052,2.188 5.896,2.188 5.896,2.188 5.76,1.635 false 5.302,2.177 5.5,2.177 5.5,2.177 5.656,1.677 false 0.646,2.073 0.813,2.073 0.813,2.073 0.917,1.458 true 0.385,0.969 0.552,0.969 0.552,0.969 0.781,1.24 true 0.073,0.167 0.385,0.365 0.313,0.198 10 false *a 3.042,0.188 3.354,0.385 0.313,0.198 10 false *b 5.177,0.167 5.49,0.365 0.313,0.198 10 false *c 2.917,2.188 3.229,2.385 0.313,0.198 10 false *d 5.115,2.094 5.427,2.292 0.313,0.198 10 false *d 3.979,2.198 4.292,2.396 0.313,0.198 10 false *e 6.104,2.104 6.417,2.302 0.313,0.198 10 false *e 4.969,1.354 5.396,1.552 0.427,0.198 10 false GND 2.823,1.344 3.25,1.542 0.427,0.198 10 false GND 0.094,0.906 0.521,1.104 0.427,0.198 10 false V+ 0.188,2.01 0.74,2.229 0.552,0.219 10 false CGND 1.333,0.583 1.76,0.781 0.427,0.198 10 false G158
*a Component with harness connected
(Navigation Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronized Signal
*e Video Waveform - -


HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) G158-12 (V+) - G158-23 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, camera lens is not covered, displaying an image
Waveform 2: Ignition switch ON, camera lens is covered, blacking out the screen

HINT:

The video waveform changes according to the image sent by the television camera assembly.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the G159 radio and display receiver assembly connector.


b.

Disconnect the U22 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G159-11 (CA+) - U22-6 (CB+) Always Below 1 Ω
G159-12 (V+) - U22-3 (CV+) Always Below 1 Ω
G159-24 (V-) - U22-2 (CV-) Always Below 1 Ω
G159-23 (CGND) - U22-5 (CGND) Always Below 1 Ω
G159-11 (CA+) - Body ground Always 10 kΩ or higher
G159-12 (V+) - Body ground Always 10 kΩ or higher
G159-24 (V-) - Body ground Always 10 kΩ or higher
G159-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E280624C09
1.458,0.323 2.01,0.583 0.552,0.26 1.094,1.031 0.813,0.729 0.813,0.729 0.469,0.729 true 1.094,1.271 1.021,1.927 1.021,1.927 0.75,1.927 true 1.552,0.354 2.167,0.552 0.615,0.198 10 false G159 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.135,0.635 0.521,0.833 0.385,0.198 10 false CA+ 0.281,1.844 0.771,2.052 0.49,0.208 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G159-23 (CGND) - Body ground Always Below 1 Ω
G159-24 (V-) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G159-11 (CA+) - Body ground Ignition switch ON 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

7.CHECK TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

7.CHECK TELEVISION CAMERA ASSEMBLY
a.

Check the waveform of the television camera assembly using an oscilloscope.

E280623C06
1.25,0.531 1.75,0.802 0.5,0.271 3.146,2.292 3.344,2.292 3.344,2.292 3.5,1.792 false 3.885,2.281 3.729,2.281 3.729,2.281 3.594,1.729 false 6.052,2.188 5.896,2.188 5.896,2.188 5.76,1.635 false 5.302,2.177 5.5,2.177 5.5,2.177 5.656,1.677 false 0.646,2.073 0.813,2.073 0.813,2.073 0.917,1.458 true 0.385,0.969 0.552,0.969 0.552,0.969 0.781,1.24 true 0.073,0.167 0.385,0.365 0.313,0.198 10 false *a 3.042,0.188 3.354,0.385 0.313,0.198 10 false *b 5.177,0.167 5.49,0.365 0.313,0.198 10 false *c 2.917,2.188 3.229,2.385 0.313,0.198 10 false *d 5.115,2.094 5.427,2.292 0.313,0.198 10 false *d 3.979,2.198 4.292,2.396 0.313,0.198 10 false *e 6.104,2.104 6.417,2.302 0.313,0.198 10 false *e 4.969,1.354 5.396,1.552 0.427,0.198 10 false GND 2.823,1.344 3.25,1.542 0.427,0.198 10 false GND 0.094,0.906 0.521,1.104 0.427,0.198 10 false V+ 0.188,2.01 0.74,2.229 0.552,0.219 10 false CGND 1.333,0.583 1.76,0.781 0.427,0.198 10 false G159
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronized Signal
*e Video Waveform - -


HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) G159-12 (V+) - G159-23 (CGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Ignition switch ON, camera lens is not covered, displaying an image
Waveform 2: Ignition switch ON, camera lens is covered, blacking out the screen

HINT:

The video waveform changes according to the image sent by the television camera assembly.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG