This DTC is stored if the television camera assembly judges that the signals or signal lines between the navigation receiver assembly*1 or radio and display receiver assembly*2 and the television camera assembly are not normal as a result of its self check.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1621 | Back Camera Power Supply Failure | Television camera assembly power supply failure | ·
Harness or connector ·
Television camera assembly ·
Navigation receiver assembly (for Navigation Receiver Type) ·
Radio and display receiver assembly (for Radio and Display Type) |
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Clear the DTCs.
Check for DTCs.
| Proceed to |
|---|
| No DTC is output |
| DTC is output (for Navigation Receiver Type) |
| DTC is output (for Radio and Display Type) |
No DTC is output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
DTC is output (for Navigation Receiver Type)
DTC is output (for Radio and Display Type)
Disconnect the G158 navigation receiver assembly connector.
Disconnect the U22 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G158-11 (CA+) - U22-6 (CB+) | Always | Below 1 Ω |
| G158-23 (CGND) - U22-5 (CGND) | Always | Below 1 Ω |
| G158-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| G158-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Navigation Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G158-23 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G158-11 (CA+) - Body ground | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G159 navigation receiver assembly connector.
Disconnect the U22 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G159-11 (CA+) - U22-6 (CB+) | Always | Below 1 Ω |
| G159-23 (CGND) - U22-5 (CGND) | Always | Below 1 Ω |
| G159-11 (CA+) - Body ground | Always | 10 kΩ or higher |
| G159-23 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G159-23 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G159-11 (CA+) - Body ground | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG