Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2013.11–2015.10
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Broadcast cannot be Received or Poor Reception  


WIRING DIAGRAM

E288613E01
5.854,2.25 6.167,2.448 0.313,0.198 10 false RA 5.854,2.427 7.083,2.833 1.229,0.406 10 false Radio and Display Receiver Assembly 6.052,1.188 6.5,1.333 0.448,0.146 10 false MAIN 6.073,1.49 6.521,1.635 0.448,0.146 10 false ANT+ 3.24,2.177 4.49,2.583 1.25,0.406 10 false No. 2 Antenna Cord Sub-assembly 4.75,2.177 5.646,2.583 0.896,0.406 10 false Antenna Cord Sub-assembly 1.781,2.167 3.031,2.573 1.25,0.406 10 false No. 3 Antenna Cord Sub-assembly 0.167,1.677 1.417,2.083 1.25,0.406 10 false Antenna with Holder Assembly 1.083,0.094 2.25,0.5 1.167,0.406 10 false Roof Antenna Pole Sub-assembly 5.458,1.083 5.625,1.25 0.167,0.167 10 false 3 5.469,1.375 5.635,1.542 0.167,0.167 10 false 5 4.75,1.083 4.917,1.25 0.167,0.167 10 false 2 4.76,1.365 4.927,1.531 0.167,0.167 10 false 3 4.073,1.083 4.24,1.25 0.167,0.167 10 false 2 4.083,1.365 4.25,1.531 0.167,0.167 10 false 3 3.344,1.094 3.51,1.26 0.167,0.167 10 false 1 3.354,1.385 3.521,1.552 0.167,0.167 10 false 3 2.052,1.104 2.219,1.271 0.167,0.167 10 false 2 2.063,1.385 2.229,1.552 0.167,0.167 10 false 3 2.646,1.083 2.813,1.25 0.167,0.167 10 false 1 2.646,1.385 2.813,1.552 0.167,0.167 10 false 3

PROCEDURE

1.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Check the radio automatic station search function by activating it.

OK:

Automatic station search function stops on a station.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK OPTIONAL COMPONENTS
2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

OK:

Optional components are not installed.


NOTICE:

Do not remove optional components without the permission of the customer.



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO ANTENNA

NG

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO ANTENNA
a.

Remove the roof antenna pole sub-assembly from the amplifier antenna assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL


b.

Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.


c.

Place a screwdriver, thin wire or other metal object on the amplifier antenna threaded installation position for the roof antenna pole sub-assembly, and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
4.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E276819

Remove the antenna connector from the radio and display receiver assembly.


b.

Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.


c.

Turn the radio on and tune into AM mode.


d.

Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.



Result:
Proceed to
OK
NG



OK

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

5.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the RA radio and display receiver assembly connector.


b.
E188455E31
1.552,1.104 1.146,1.479 true 0.844,1.51 1.24,1.677 0.396,0.167 10 ANT+

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
5 (ANT+) - Body ground Ignition switch ACC
Radio switch on and FM or AM selected
11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E288614C03
0.531,0.771 0.99,0.99 0.458,0.219 0.969,1.583 1.219,1.583 1.219,1.583 1.469,1.25 true 2.354,0.708 2.104,0.708 2.104,0.708 1.938,0.958 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.104,1.823 0.417,2.021 0.313,0.198 10 false *b 0.667,0.802 0.979,1 0.313,0.198 10 false RA 0.604,1.5 1.115,1.677 0.51,0.177 10 false MAIN 2.385,0.615 2.896,0.792 0.51,0.177 10 false ANT+
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the radio and display receiver assembly connector.


b.

Remove the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
RA-3 (MAIN) - 2 Always Below 1 Ω
RA-5 (ANT+) - 3 Always Below 1 Ω
RA-3 (MAIN) - Body ground Always 10 kΩ or higher
RA-5 (ANT+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

7.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288795C02
0.26,0.104 0.573,0.26 0.313,0.156 10 false *a 0.271,1.677 0.583,1.833 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Remove the antenna connector from the antenna cord sub-assembly.


b.

Remove the antenna connector from the No. 3 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
3 - 3 Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

8.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E288794C02
0.385,0.156 0.698,0.313 0.313,0.156 10 false *a 0.448,1.708 0.76,1.865 0.313,0.156 10 false *b
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna with Holder Assembly)


Remove the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Remove the antenna connector from the antenna with holder assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
3 - 3 Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

9.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION

OK:

The roof antenna pole sub-assembly is installed properly



Result:
Proceed to
OK
NG



OK

10.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

REINSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

10.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Replace the roof antenna pole sub-assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (ROOF ANTENNA POLE SUB-ASSEMBLY IS DEFECTIVE)

NG

11.CHECK ANTENNA WITH HOLDER ASSEMBLY
11.CHECK ANTENNA WITH HOLDER ASSEMBLY
a.

Replace the antenna with holder assembly and check if radio broadcasts can be received normally.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA HOLDER>REMOVAL

OK:

Radio broadcasts can be received normally.



Result:
Proceed to
OK
NG



OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY