Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › 2013.11–2015.10
RM3090E _56 Audio / Visual / Telematics _008775 AUDIO / VIDEO _0048748 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B157D  DAB Tuner Antenna Disconnected  


DESCRIPTION

This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna cable which is connected to the radio and display receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B157D DAB Tuner Antenna Disconnected The digital audio broadcasting antenna cable is not connected.
·

Antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

Roof antenna pole sub-assembly

·

Antenna with holder assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E288613E03
5.854,2.25 6.167,2.448 0.313,0.198 10 false DB 5.854,2.427 7.083,2.833 1.229,0.406 10 false Radio and Display Receiver Assembly 3.24,2.177 4.49,2.583 1.25,0.406 10 false No. 2 Antenna Cord Sub-assembly 4.75,2.177 5.646,2.583 0.896,0.406 10 false Antenna Cord Sub-assembly 1.781,2.167 3.031,2.573 1.25,0.406 10 false No. 3 Antenna Cord Sub-assembly 0.167,1.677 1.417,2.083 1.25,0.406 10 false Antenna with Holder Assembly 1.083,0.094 2.25,0.5 1.167,0.406 10 false Roof Antenna Pole Sub-assembly 5.458,1.083 5.625,1.25 0.167,0.167 10 false 1 5.396,1.375 5.708,1.542 0.313,0.167 10 false 1a 4.75,1.083 4.917,1.25 0.167,0.167 10 false 1 4.76,1.375 5.052,1.552 0.292,0.177 10 false 1a 4.083,1.083 4.25,1.25 0.167,0.167 10 false 2 3.99,1.365 4.302,1.531 0.313,0.167 11 false 2a 3.354,1.094 3.521,1.26 0.167,0.167 10 false 2 3.354,1.385 3.74,1.573 0.385,0.188 10 false 2a 2.073,1.104 2.24,1.271 0.167,0.167 10 false 1 2.073,1.385 2.354,1.552 0.281,0.167 10 false 1a 2.646,1.083 2.813,1.25 0.167,0.167 10 false 2 2.573,1.385 2.854,1.583 0.281,0.198 10 false 2a

PROCEDURE

1.CHECK CONNECTION OF DAB RADIO ANTENNA CABLE
a.

Check if the DAB radio antenna cable is securely connected to the radio and display receiver assembly.

OK:

DAB radio antenna cable is securely connected



Result:
Proceed to
OK
NG



OK

2.CHECK ANTENNA CORD SUB-ASSEMBLY

NG

SECURELY CONNECT DAB RADIO ANTENNA CABLE

2.CHECK ANTENNA CORD SUB-ASSEMBLY
a.
E288617C02
0.594,0.729 1.104,1.021 0.51,0.292 1.792,1.083 2.208,1.417 2.208,1.417 2.458,1.417 true 1.948,2.542 2.281,2.125 2.281,2.125 2.531,2.125 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.104,1.75 0.417,1.948 0.313,0.198 10 false *b 2.51,1.333 2.823,1.531 0.313,0.198 10 false 1a 2.583,2.042 2.896,2.24 0.313,0.198 10 false 1a 0.75,0.792 1.063,0.99 0.313,0.198 10 false DB
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Remove the antenna connector from the radio and display receiver assembly.


b.

Remove the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DB-1 - 1 Always Below 1 Ω
DB-1a - 1a Always Below 1 Ω
DB-1 - Body ground Always 10 kΩ or higher
DB-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

3.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.
E288615C01
1.323,0.583 1.156,0.25 1.156,0.25 0.906,0.25 true 2.167,2.333 2.333,2 2.333,2 2.583,2 true 0.698,0.156 1.01,0.354 0.313,0.198 10 false 1a 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.104,1.885 0.417,2.083 0.313,0.198 10 false *b 2.625,1.917 2.938,2.115 0.313,0.198 10 false 2a
*a Front view of wire harness connector
(to Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly)


Remove the antenna connector from the antenna cord sub-assembly.


b.

Remove the antenna connector from the No. 3 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Always Below 1 Ω
1a - 2a Always Below 1 Ω
1 - Body ground Always 10 kΩ or higher
1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

4.CHECK NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E288616C01
1.938,2.542 2.271,2.208 2.271,2.208 2.521,2.208 true 1.385,0.844 1.052,0.51 1.052,0.51 0.802,0.51 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.104,1.719 0.417,1.917 0.313,0.198 10 false *b 2.552,2.125 2.865,2.323 0.313,0.198 10 false 1a 0.604,0.417 0.917,0.615 0.313,0.198 10 false 2a
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna with Holder Assembly)


Remove the antenna connector from the No. 2 antenna cord sub-assembly.


b.

Remove the antenna connector from the antenna with holder assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 1 Always Below 1 Ω
2a - 1a Always Below 1 Ω
2 - Body ground Always 10 kΩ or higher
2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

5.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION

OK:

The roof antenna pole sub-assembly is installed properly



Result:
Proceed to
OK
NG



OK

6.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

REINSTALL ROOF ANTENNA POLE SUB-ASSEMBLY

6.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Replace the roof antenna pole sub-assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (ROOF ANTENNA POLE SUB-ASSEMBLY IS DEFECTIVE)

NG

7.CHECK ANTENNA WITH AMPLIFIER ASSEMBLY
7.CHECK ANTENNA WITH AMPLIFIER ASSEMBLY
a.

Replace the antenna with holder assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA HOLDER>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY