Home › Drivetrain › CLUTCH › CLUTCH UNIT(for Diesel) › 2013.11–2015.10
RM3090E _52 Drivetrain _008754 CLUTCH _0050268 CLUTCH UNIT(for Diesel) A

CLUTCH  CLUTCH UNIT(for Diesel)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C116730C02
2.458,1.177 2.635,1.313 2.635,1.313 2.771,1.313 false 2.302,3.365 2.521,3.552 0.219,0.188 10 *a 2.802,1.229 3.104,1.635 0.302,0.406 10 SST
*a Transaxle side


Insert SST into the clutch disc assembly, and then insert them into the flywheel.

SST
09301-00310  

NOTICE:

Do not insert the clutch disc assembly in the wrong direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C116732C01
1.427,1.917 1.552,2.063 1.552,2.063 1.813,2.063 true 0.854,1.844 0.781,1.99 0.781,1.99 0.49,1.99 false 0.594,1.479 0.479,1.542 0.479,1.542 0.292,1.542 false 0.625,0.594 0.51,0.344 0.51,0.344 0.344,0.344 false 1.656,1.094 0.823,0.75 0.823,0.75 0.354,0.75 true 1.219,0.354 1.969,0.115 1.969,0.115 2.667,0.115 true 1.688,1.583 2.188,1.542 2.188,1.542 1.792,1.635 true 0.26,1.917 0.385,2.073 0.125,0.156 10 2 0.115,1.469 0.24,1.625 0.125,0.156 10 5 2.802,0.052 2.927,0.208 0.125,0.156 10 1 0.167,0.677 0.333,0.854 0.167,0.177 10 6 0.167,0.271 0.292,0.427 0.125,0.156 10 3 1.917,1.969 2.042,2.125 0.125,0.156 10 4 2.25,1.448 2.448,1.635 0.198,0.188 10 *a
*a Matchmark


Align the matchmarks on the clutch cover assembly with the one on the flywheel.


b.

Tighten the 6 bolts uniformly in the order shown in the illustration, starting with the bolt located near the knock pin on the top.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Following the order in the illustration, make sure to uniformly tighten the bolts 180°.

·

After checking that the disc is in the center, gently move SST up and down, and right and left to tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C116193

C116192N02
0.677,1.229 0.573,1.542 0.573,1.542 0.438,1.542 false 0.094,1.479 0.396,1.792 0.302,0.313 10 SST

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

Maximum misalignment:

1.3 mm (0.0512 in.)


If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.
C304173

Install the release fork support to the manual transaxle assembly.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 31126 5.INSTALL CLUTCH RELEASE FORK BOOT

a.
C113599

Install the clutch release fork boot onto the manual transaxle assembly.


Hide 31204 6.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C133433C01
1.552,1.198 1.635,1.281 0.083,0.083 10 false .
V100135

Multemp 8158 grease or equivalent


Apply Multemp 8158 grease or equivalent to the following areas:

·

The surfaces on the clutch release fork sub-assembly that contact the clutch release bearing.


·

The surfaces on the clutch release fork sub-assembly that contact the push rod of the clutch release fork support.


·

The surfaces on the clutch release fork sub-assembly that contact the clutch release fork support.


Grease:

Multemp 8158 grease or equivalent



b.

Install the clutch release fork sub-assembly to the clutch release bearing.


Hide 31230 7.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.
C133434C01
1.583,1.406 1.635,1.51 false
V100135

Toyota Genuine Clutch Spline Grease or equivalent


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



b.
C113576

Install the clutch release bearing with clutch release fork sub-assembly to the manual transaxle assembly.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.