Home › Engine / Hybrid System › 2AD-FTV INTAKE / EXHAUST › EXHAUST PIPE › from 2014.10
RM3090E _51 Engine / Hybrid System _008383 2AD-FTV INTAKE / EXHAUST _0046768 EXHAUST PIPE A

2AD-FTV INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for DPF)

Hide 17410 2.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Check the free length of the compression spring.

i.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.63 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A291393C02
2.417,1.083 3.083,1.083 true 0.917,1.917 1.083,1.917 1.083,1.917 2.042,1.583 true 0.771,1.813 1.083,1.969 0.313,0.156 10 false *1 3.115,0.979 3.427,1.135 0.313,0.156 10 false *a
*1 Gasket
*a Wooden Block


Using a hammer and wooden block, tap on a new gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket by dropping it, etc.

·

Do not damage the outer surface of the gasket.

·

Do not push on the gasket with the front exhaust pipe assembly when connecting it.




c.

Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.


d.

Install the front exhaust pipe assembly and 2 compression springs with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 51442 3.INSTALL NO. 2 ENGINE UNDER COVER

Hide 50819 4.INSTALL FRONT FLOOR COVER

Hide 17430 5.INSTALL TAILPIPE ASSEMBLY

a.

Check the free length of the compression spring.

i.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

38.5 mm (1.52 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A291393C02
2.417,1.083 3.083,1.083 true 0.917,1.917 1.083,1.917 1.083,1.917 2.042,1.583 true 0.771,1.813 1.083,1.969 0.313,0.156 10 false *1 3.115,0.979 3.427,1.135 0.313,0.156 10 false *a
*1 Gasket
*a Wooden Block


Using a hammer and wooden block, tap on a new gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket by dropping it, etc.

·

Do not damage the outer surface of the gasket.

·

Do not push on the gasket with the tailpipe assembly when connecting it.




c.

Connect the tailpipe assembly to the 2 exhaust pipe supports.


d.

Install the tailpipe assembly and 2 compression springs with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 6.INSPECT FOR EXHAUST GAS LEAK

a.

Check that there are no exhaust gas leaks from the points (connection areas of the exhaust pipes and installation areas of each sensor).