Home › Engine / Hybrid System › 2AD-FTV ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2014.10
RM3090E _51 Engine / Hybrid System _008372 2AD-FTV ENGINE MECHANICAL _0046711 ENGINE ASSEMBLY A

2AD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.


PROCEDURE

Hide 12305 1.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.

Install the engine mounting insulator sub-assembly RH with the 3 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 12372A 2.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.

Install the engine mounting insulator LH with the 4 bolts.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 12371A 3.INSTALL REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A295905N01
0.625,1.76 0.802,1.979 0.177,0.219 10 1 0.99,1.938 1.167,2.156 0.177,0.219 10 3 2.042,1.188 2.219,1.406 0.177,0.219 10 4 2.531,1.49 2.708,1.708 0.177,0.219 10 2

Install the rear engine mounting insulator with the 2 bolts and 2 nuts in the order shown in the illustration.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 5.REMOVE ENGINE FROM ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Install a sling device and chain block to the engine and hang the engine.


b.

Remove the engine from the engine stand.


Hide 13450 7.INSTALL FLYWHEEL WITH DAMPER ASSEMBLY (for Manual Transaxle)

a.
A297509N01
0.969,0.75 1.417,0.229 1.417,0.229 1.677,0.229 true 1.688,1.802 1.792,1.354 1.792,1.354 2.052,1.354 true 0.896,1.01 1.552,0.667 1.552,0.667 1.813,0.667 true 1.719,0.115 2.177,0.313 0.458,0.198 10 SST 1.854,0.563 2.313,0.76 0.458,0.198 10 SST 2.083,1.24 2.542,1.438 0.458,0.198 10 SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


b.
A297521N01
1.927,0.479 2.083,0.677 0.156,0.198 10 1 2.198,1.781 2.354,1.979 0.156,0.198 10 2 2.667,1.01 2.823,1.208 0.156,0.198 10 3 1.302,1.354 1.448,1.563 0.146,0.208 10 4 1.354,0.823 1.5,1.031 0.146,0.208 10 8 2.51,0.604 2.656,0.813 0.146,0.208 10 5 1.708,1.823 1.854,2.031 0.146,0.208 10 6 2.594,1.417 2.75,1.615 0.156,0.198 10 7

Using a T55 "TORX" socket wrench, install the flywheel with damper assembly with 8 new bolts and uniformly tighten the bolts in several steps in the sequence shown in the illustration.

Torque:
70.6 N*m (720 kgf*cm, 52 ft.*lbf)

NOTICE:
·

Do not reuse the flywheel installation bolts.

·

Be sure to check the tightening torque within 5 minutes after tightening.

·

Do not impact or damage the flywheel installation bolts. Be sure to handle them carefully.

·

Make sure there is no oil on the bolts.



HINT:

Make sure that the seating surface of the flywheel installation bolts and installation surfaces of the crankshaft and flywheel with damper assembly are free from oil and foreign matter.



Hide 32101 8.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)

a.
A297509N01
0.969,0.75 1.417,0.229 1.417,0.229 1.677,0.229 true 1.688,1.802 1.792,1.354 1.792,1.354 2.052,1.354 true 0.896,1.01 1.552,0.667 1.552,0.667 1.813,0.667 true 1.719,0.115 2.177,0.313 0.458,0.198 10 SST 1.854,0.563 2.313,0.76 0.458,0.198 10 SST 2.083,1.24 2.542,1.438 0.458,0.198 10 SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


b.
A215653C01
0.792,0.552 1.042,0.552 1.042,0.552 1.604,0.281 false 2.188,0.948 2.5,0.646 2.5,0.646 2.708,0.646 false 0.354,1.896 0.604,1.896 0.604,1.896 1.167,1.625 false 0.615,0.458 0.927,0.615 0.313,0.156 10 false *1 2.729,0.552 3.042,0.708 0.313,0.156 10 false *2 0.167,1.781 0.479,1.938 0.313,0.156 10 false *3 0.531,1.25 0.844,1.406 0.313,0.156 10 false *a 2.698,1.26 2.969,1.417 0.271,0.156 10 false *b
*1 Drive Plate and Ring Gear Sub-assembly
*2 Rear Drive Plate Spacer
*3 Front Drive Plate Spacer
(Reversible)
*a Engine Side
*b Transaxle Side


Install the front drive plate spacer, drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.

HINT:
·

The front drive plate spacer is reversible.

·

As the rear drive plate spacer and drive plate and ring gear sub-assembly are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.




c.
A057108C42
1.99,0.427 1.698,1.302 false 2.052,0.354 2.24,0.521 0.188,0.167 10 *1
*1 Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A297522N01
1.625,0.469 1.781,0.667 0.156,0.198 10 false 1 2.042,0.531 2.198,0.729 0.156,0.198 10 false 7 2.219,0.854 2.375,1.052 0.156,0.198 10 false 4 2.125,1.26 2.281,1.458 0.156,0.198 10 false 6 1.792,1.573 1.948,1.771 0.156,0.198 10 false 2 1.469,1.542 1.625,1.74 0.156,0.198 10 false 8 1.198,1.229 1.354,1.427 0.156,0.198 10 false 3 1.229,0.771 1.385,0.969 0.156,0.198 10 false 5

Install and uniformly tighten the 8 bolts in several steps, in the sequence shown in the illustration.

Torque:
92 N*m (938 kgf*cm, 68 ft.*lbf)

NOTICE:

Do not start the engine for at least an hour after installing the drive plate and ring gear sub-assembly.



Hide 31250 9.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 10.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31210 11.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 30300 12.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 30500 13.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)

Hide 33119C 14.INSTALL STIFFENER PLATE LH

a.
A297523N01
2.625,0.406 2.781,0.604 0.156,0.198 10 A 1.417,1.74 1.573,1.938 0.156,0.198 10 D 1.552,1.458 1.708,1.656 0.156,0.198 10 C 2.271,0.25 2.427,0.448 0.156,0.198 10 B

Temporarily install the stiffener plate LH with the 4 bolts.


b.

While holding the stiffener plate LH against the transaxle assembly, tighten bolt A, and then tighten bolts B, C and D.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 33118D 15.INSTALL STIFFENER PLATE RH

a.
A297524N01
1.688,1.167 1.844,1.365 0.156,0.198 10 D 0.573,1.323 0.729,1.521 0.156,0.198 10 B 2.073,1.167 2.229,1.365 0.156,0.198 10 A 1.198,0.167 1.354,0.365 0.156,0.198 10 C

Temporarily install the stiffener plate RH with the 4 bolts.


b.

While holding the stiffener plate RH against the transaxle assembly, tighten bolt A, and then tighten bolts B, C and D.

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 12156 16.INSTALL OIL PAN INSULATOR

a.

Install the oil pan insulator with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12325A 17.INSTALL ENGINE MOUNTING BRACKET LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket LH is necessary.


a.

Install the engine mounting bracket LH with the 4 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12321A 18.INSTALL REAR ENGINE MOUNTING BRACKET

a.

Temporarily install the rear engine mounting bracket with the 4 bolts.


b.
A297541N01
0.969,1.26 1.125,1.458 0.156,0.198 10 3 2.25,0.833 2.406,1.031 0.156,0.198 10 1 2.031,1.688 2.188,1.885 0.156,0.198 10 2 1.333,1.781 1.49,1.979 0.156,0.198 10 4

Tighten the 4 bolts of the rear engine mounting bracket in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 12311A 19.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
A224433N01
2.354,0.771 2.51,0.969 0.156,0.198 10 2 1.927,0.208 2.083,0.406 0.156,0.198 10 3 1.771,1.865 1.927,2.063 0.156,0.198 10 1

for Manual Transaxle:

Temporarily install the front engine mounting bracket with the 3 bolts.


b.

for Manual Transaxle:

Tighten the 3 bolts of the front engine mounting bracket in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


c.
A299157N01
1.052,1.167 1.208,1.365 0.156,0.198 10 1 0.979,0.094 1.135,0.292 0.156,0.198 10 4 2.021,1.219 2.177,1.417 0.156,0.198 10 3 2.042,0.073 2.198,0.271 0.156,0.198 10 2

for Automatic Transaxle:

Temporarily install the front engine mounting bracket with the 4 bolts.


d.

for Automatic Transaxle:

Tighten the 4 bolts of the front engine mounting bracket in the order shown in the illustration.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 28100 21.INSTALL STARTER ASSEMBLY

Hide 17361J 22.INSTALL NO. 1 AIR TUBE

a.

Install the No. 1 air tube with the 2 bolts and tighten the clamp.

Torque:
for bolt : 24 N*m (245 kgf*cm, 18 ft.*lbf)
for clamp : 6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:

Before installation, remove any oil residue from the inside of the No. 1 air tube and air hose.



Hide 23.INSTALL ENGINE WITH TRANSAXLE

a.

Temporarily install the front engine mounting insulator with the through bolt and nut.


b.
A295909C01
1.979,3.031 2.521,3.177 2.521,3.177 2.74,3.177 true 1.438,2.698 1.688,2.698 1.688,2.698 1.823,3.063 true 2.75,3.052 3.063,3.208 0.313,0.156 10 *1 1.25,2.594 1.563,2.75 0.313,0.156 10 *2
*1 Alignment Mark
*2 Protrusion


Temporarily install the front suspension member with the through bolt.

HINT:

When installing the front suspension member, align the protrusion of the engine mounting bracket with the alignment mark of the engine mounting insulator.



c.

Set the engine assembly with transaxle on the engine lifter.

HINT:

Place the engine on wooden blocks or equivalent so that the engine is level.



d.

Operate the engine lifter and lift the engine assembly with transaxle to the position where the engine mounting insulator LH and engine mounting insulator sub-assembly RH can be installed.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While raising the engine into the vehicle, do not allow it to contact the vehicle.

·

Align the matchmarks on the intermediate shaft and pinion.




e.

Temporarily install the 2 bolts to the front suspension member sub-assembly.


f.

Temporarily install the front suspension member rear brace RH and front suspension member rear brace LH with the 6 bolts.


g.

Connect the engine mounting insulator LH with the bolt and nut.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)

HINT:

While holding the bolt in place, tighten the nut.



h.
A297529N01
1.198,1.854 1.354,2.052 0.156,0.198 10 B 2.458,1.771 2.615,1.969 0.156,0.198 10 A

Connect the engine mounting insulator sub-assembly RH with the 2 bolts and 2 nuts.

Torque:
for bolt and nut A : 95 N*m (969 kgf*cm, 70 ft.*lbf)
for nut B : 52 N*m (530 kgf*cm, 38 ft.*lbf)


i.
A273397E01
1.104,1.646 1.271,1.844 0.167,0.198 10 true A 0.146,2.688 0.302,2.885 0.156,0.198 10 true B 2.229,1.667 2.396,1.865 0.167,0.198 10 true A 0.323,0.594 0.625,0.781 0.302,0.188 10 true . A 3.042,0.542 3.24,0.75 0.198,0.208 10 true A 1.344,2.917 1.5,3.115 0.156,0.198 10 true B 1.969,2.979 2.125,3.177 0.156,0.198 10 true B 3.25,2.792 3.406,2.99 0.156,0.198 10 true B

Tighten the 8 bolts.

Torque:
for bolt A : 137 N*m (1397 kgf*cm, 101 ft.*lbf)
for bolt B : 93 N*m (948 kgf*cm, 69 ft.*lbf)


j.
A297527N01
0.198,0.333 0.365,0.5 0.167,0.167 10 A 0.719,0.365 0.885,0.531 0.167,0.167 10 A 2.573,0.313 2.74,0.479 0.167,0.167 10 A 3.094,0.344 3.26,0.51 0.167,0.167 10 A 2.031,0.5 2.198,0.667 0.167,0.167 10 B 2.021,1.625 2.188,1.792 0.167,0.167 10 B

Install the front crossmember sub-assembly with the 6 bolts.

Torque:
for bolt A : 99 N*m (1010 kgf*cm, 73 ft.*lbf)
for bolt B : 95 N*m (969 kgf*cm, 70 ft.*lbf)


k.

Remove the 2 bolts, No. 1 engine hanger and No. 2 engine hanger.


l.

Tighten the through bolt of the rear engine mounting insulator.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)

HINT:

Check that the protrusion of the engine mounting bracket is aligned with the alignment mark of the engine mounting insulator.



m.

Tighten the through bolt and nut of the front engine mounting insulator.

Torque:
145 N*m (1479 kgf*cm, 107 ft.*lbf)

NOTICE:

While holding the nut in place, tighten the through bolt.



Hide 23292D 24.INSTALL FUEL HOSE PROTECTOR

a.

Install the fuel hose protector to the cylinder head sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 51218A 25.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A295896

Install the front suspension member reinforcement LH with the 4 bolts.

Torque:
99 N*m (1010 kgf*cm, 73 ft.*lbf)


Hide 51217A 26.INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

Hide 32101A 27.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for Automatic Transaxle)

a.

Turn the crankshaft to gain access to the installation locations of the 6 torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

Install the black bolt first, and then the 5 silver bolts.



b.

Install the oil pan insulator and temporarily install the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 30.INSTALL FRONT AXLE ASSEMBLY LH

Hide 31.INSTALL FRONT AXLE ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 32.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 33.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 34.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 35.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 36.CONNECT FRONT SPEED SENSOR LH

Hide 37.CONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 38.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 39.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 45025D 40.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 41.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 42.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 31470 43.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

a.
A297525N01
0.844,0.865 1,1.063 0.156,0.198 10 A 1.75,0.438 1.906,0.635 0.156,0.198 10 A 1.76,1.875 1.917,2.073 0.156,0.198 10 B 2.177,1.958 2.333,2.156 0.156,0.198 10 B

Connect the clutch release cylinder assembly and clutch flexible hose bracket with the 4 bolts.

Torque:
for bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)
for bolt B : 19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 33820B 44.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.

Connect the transmission control cable assembly to the transmission control cable bracket with 2 new clips.


b.

Install the 2 pins.


Hide 33820B 45.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

a.

Connect the transmission control cable assembly with the nut and a new clip.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 88704 46.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

Compressor Oil:

ND-OIL 8 or equivalent



b.

Install the O-ring to the suction hose sub-assembly.


c.

Connect the suction hose sub-assembly to the cooler compressor assembly and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


d.

Connect the connector to the cooler compressor assembly.


Hide 88703 47.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

Compressor Oil:

ND-OIL 8 or equivalent



b.

Install the O-ring to the discharge hose sub-assembly.


c.

Connect the discharge hose sub-assembly to the cooler compressor assembly and install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 16470 48.INSTALL RADIATOR RESERVOIR ASSEMBLY

a.

Install the radiator reservoir assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the water by-pass hose to the radiator reservoir assembly, and slide the clamp to secure the hose.


Hide 16264D 49.CONNECT NO. 2 WATER BY-PASS HOSE

a.

Connect the No. 2 water by-pass hose to the No. 4 water by-pass pipe and slide the clamp to secure the hose.


Hide 16572D 50.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet housing and slide the clamp to secure the hose.


Hide 17342F 51.INSTALL INTERCOOLER AIR HOSE

Hide 16057 52.CONNECT RADIATOR HOSE SUB-ASSEMBLY

a.

Connect the radiator hose sub-assembly to the cylinder head sub-assembly and slide the clamp to secure the hose.


Hide 87245A 53.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose to the No. 3 water by-pass pipe and slide the clamp to secure the hose.


Hide 87245A 54.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose to the cylinder head sub-assembly and slide the clamp to secure the hose.


Hide 55.CONNECT HOSES AND CONNECTORS

a.

Connect the vacuum pump hose to the vacuum pump assembly and slide the clip to secure the hose.


b.

Install the injector driver assembly with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

for CCo:

Connect the 4 injector driver connectors and attach the wire harness clamp.


d.

for DPF:

Connect the 4 injector driver connectors and attach the 2 wire harness clamps.


e.

Attach the 3 wire harness clamps to the 3 wire harness clamp brackets.


f.

for Automatic Transaxle:

Connect the shift position switch connector and attach the 2 wire harness clamps.


g.

for Automatic Transaxle:

Install the ground cable with the bolt to the automatic transaxle.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


h.

for Automatic Transaxle:

Connect the transaxle ECM connector and attach the 2 wire harness clamps.


i.

for Manual Transaxle:

Install the bolt to the manual transaxle assembly.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


j.

for Manual Transaxle:

Connect the 2 connectors and attach the wire harness clamp.


k.

for Manual Transaxle:

Install the ground cable with the bolt and attach the wire harness clamp.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


l.

Install the wire harness clamp bracket with the bolt.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


m.

Connect the starter wire with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


n.

Install the bolt and attach the engine wire cover clamp and engine wire harness clamp.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


o.

Attach the 2 claws and connect the engine wire to the engine room No. 1 relay block with the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


p.

Connect the 3 connectors to the engine room No. 1 relay block.


q.

Install the engine room relay block and junction block cover.


Hide 17119A 57.INSTALL AIR CLEANER BRACKET

a.

Install the air cleaner bracket with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the 2 fuel hoses to the air cleaner bracket.


c.

Attach the 3 wire harness clamps.


d.

Connect the glow plug relay and level warning switch connector.


Hide 58.INSTALL FUEL FILTER ASSEMBLY

a.

Install the fuel filter assembly to the air cleaner bracket with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Connect the 2 fuel hoses to the fuel filter assembly and slide the clamp secure the hoses.


Hide 17769 59.INSTALL AIR CLEANER SUPPORT

a.

Install the air cleaner support with the 2 nuts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 60.INSTALL AIR CLEANER CASE

a.

Install the air cleaner case with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17801 61.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17705 62.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

a.

Install the air cleaner cap sub-assembly and attach the 3 clips.


b.

Connect the mass air flow meter connector and wire harness clamp.


c.

Connect the air cleaner hose and tighten the hose clamp.


d.

Connect the PCV hose.


Hide 25770A 64.CONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

Hide 16400 65.INSTALL RADIATOR ASSEMBLY (for Automatic Transaxle)

Hide 74414B 66.INSTALL BATTERY BRACKET REINFORCEMENT

a.

Install the battery bracket reinforcement with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 74411B 67.INSTALL FRONT BATTERY BRACKET

a.

Install the front battery bracket with the 4 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 wire harness clamps.


Hide 74431 68.INSTALL BATTERY TRAY

Hide 28800 69.INSTALL BATTERY

Hide 28899 70.INSTALL BATTERY INSULATOR

Hide 74404A 71.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Attach the hook of the battery clamp sub-assembly to the front battery bracket.


b.

Partially tighten the nut and temporarily install the bolt.


c.

Attach the 2 wire harness clamps.


d.

Adjust the battery clamp position.


e.

Tighten the nut and bolt.

Torque:
for bolt : 17 N*m (173 kgf*cm, 13 ft.*lbf)
for nut : 4.9 N*m (50 kgf*cm, 43 in.*lbf)


Hide 89480A 72.INSTALL DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

Hide 37100 73.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 17410 74.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 52119A 75.INSTALL FRONT BUMPER COVER (for Automatic Transaxle)

Hide 76.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 78.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 79.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 81.ADD AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)

Hide 86.PERFORM REGISTRATION (for CCo)

a.

Perform registration of the injector compensation codes.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION


b.

Perform registration of the pilot quantity learning.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for CCo)>REGISTRATION


Hide 87.PERFORM REGISTRATION (for DPF)

a.

Perform registration of the injector compensation codes.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION


b.

Perform registration of the pilot quantity learning.

Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION


Hide 89.PERFORM THROTTLE VALVE FULLY CLOSED POSITION LEARNING

Hide 91.INSPECT FOR COOLANT LEAK

Hide 94.INSPECT FOR MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)

Hide 95.ADJUSTMENT AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)

Hide 51443 96.INSTALL REAR ENGINE UNDER COVER RH

Hide 51444 97.INSTALL ENGINE UNDER COVER REAR LH

a.

Install the rear engine under cover LH with the 2 clips.


Hide 58165C 98.INSTALL FRONT FLOOR COVER RH

a.

Install the front floor cover RH with the 3 nuts and 3 clips.


Hide 51442 99.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the bolt and clip.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 50819 100.INSTALL FRONT FLOOR COVER

Hide 51441 101.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 10 clips.


b.

Install the 4 bolts and 2 screws.


Hide 12611 102.INSTALL NO. 1 ENGINE COVER

a.

Attach the 4 clips to install the No. 1 engine cover.