12108
1.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly.
12108A
2.REMOVE OIL FILLER CAP GASKET
Remove the oil filler cap gasket.
12635
3.REMOVE ENGINE COVER JOINT
Remove the 2 engine cover joints.
19100P
4.REMOVE SPARK PLUG
11101W
5.REMOVE CAMSHAFT POSITION SENSOR
for Intake Side:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL
for Exhaust Side:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL
11101J
6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
for Intake Side:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>REMOVAL
for Exhaust Side:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>REMOVAL
11401G
7.REMOVE CRANKSHAFT POSITION SENSOR
83530
8.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
89615
9.REMOVE KNOCK SENSOR
89422
10.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
11201
11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 13 bolts, seal washer and cylinder head cover sub-assembly.
Remove the 3 gaskets from the camshaft bearing cap.
As gaskets may stick to the cylinder head cover sub-assembly, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover sub-assembly.
11213
12.REMOVE CYLINDER HEAD COVER GASKET
Remove the cylinder head cover gasket.
11193
13.REMOVE SPARK PLUG TUBE GASKET
Pry up the 4 claws of the ventilation baffle plate.
Do not deform the claws of the ventilation baffle plate more than necessary.
Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 4 spark plug tube gaskets from cylinder head cover sub-assembly.
As much as possible prevent the spark plug tube gaskets from being deformed.
The removed spark plug tube gaskets will be used when reinstalling the new spark plug tube gaskets.
Do not damage the cylinder head cover sub-assembly.
Make sure not to damage the spark plug tube gasket and cylinder head cover sub-assembly when inserting the screwdriver in the joint area.
If the cylinder head cover sub-assembly is damaged, smooth the surface with 400-grid sandpaper.
15620
14.REMOVE OIL FILTER CAP ASSEMBLY
15.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *1 | Timing Mark |
| *2 | Notch |
Turn the crankshaft pulley until its notch and timing mark "0" of the timing chain cover are aligned.
Check that the timing marks on both the camshaft timing exhaust gear and camshaft timing gear are facing upward as shown in the illustration.
If the marks are not as shown, turn the crankshaft 1 complete revolution (360°) and align the marks as specified above.
13471
16.REMOVE CRANKSHAFT PULLEY
13540
17.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Remove the 2 nuts, bracket, No. 1 chain tensioner assembly and gasket.
Do not turn the crankshaft without the No. 1 chain tensioner installed.
18.REMOVE ENGINE MOUNTING BRACKET STUD BOLT
Remove the engine mounting bracket stud bolt.
11302
19.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
11302A
20.REMOVE TIMING CHAIN COVER OIL SEAL
16323
21.REMOVE WATER INLET HOUSING
Remove the 3 bolts, water inlet housing and gasket.
12511
22.REMOVE NO. 1 GENERATOR BRACKET
Remove the 4 bolts and No. 1 generator bracket.
13559
23.REMOVE CHAIN TENSIONER SLIPPER
Remove the chain tensioner slipper from the cylinder block assembly.
13561
24.REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper.
13506
25.REMOVE CHAIN SUB-ASSEMBLY
Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to loosen the chain sub-assembly between the camshaft timing gears.
With the chain sub-assembly loosened, release the chain sub-assembly from the camshaft timing gear and place it on the camshaft timing gear.
Be sure to release the chain sub-assembly from the sprocket completely.
Turn the camshaft clockwise to return it to the original position and remove the chain sub-assembly.
13521
26.REMOVE CRANKSHAFT TIMING SPROCKET
13507
27.REMOVE NO. 2 CHAIN SUB-ASSEMBLY
19315
28.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
Remove the No. 1 crankshaft position sensor plate.
13521A
29.REMOVE CRANKSHAFT TIMING GEAR KEY
| *1 | Protective Tape |
Using a screwdriver, remove the 2 crankshaft timing gear keys.
Tape the screwdriver tip before use.
13050
30.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
13070A
31.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
13050
32.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
13070A
33.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
13908
34.REMOVE VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY
13908
35.INSTALL VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY
11103
36.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
222A0
37.REMOVE CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY
Using a screwdriver, slide the control actuator clip from the control actuator connector.
Slide only the upper part of the control actuator clip, as the straight pin may fall if the control actuator clip is completely removed.
Using 2 screwdrivers, lightly pry the control actuator connector to make a space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly.
Do not forcefully pry the control actuator connector.
Do not damage the camshaft housing sub-assembly and camshaft bearing cap.
Using a magnet hand, remove the straight pin from the control actuator connector.
The straight pin can be removed by utilizing the space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly to move the continuously variable valve lift controller assembly so that there is no load on the straight pin.
| *1 | Continuously Variable Valve Lift Controller Assembly |
| *2 | O-Ring |
Remove the bolt and the continuously variable valve lift controller assembly from the camshaft housing sub-assembly.
Remove the O-ring from the continuously variable valve lift controller assembly.
The O-ring may remain on the camshaft housing side. Be sure to always remove it.
Remove the valve lift control actuator connector from the valve rocker shaft.
13801
38.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 16 No. 1 valve rocker arm sub-assemblies.
Arrange the removed parts in the correct order.
13750
39.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.
Arrange the removed parts in the correct order.
13716
40.REMOVE VALVE STEM CAP
Remove the 16 valve stem caps.
Arrange the removed parts in the correct order.
11101
41.REMOVE CYLINDER HEAD SUB-ASSEMBLY
11114A
42.REMOVE CAMSHAFT HOUSING STRAIGHT PIN
It is not necessary to remove a straight pin unless it is being replaced.
11115
43.REMOVE CYLINDER HEAD GASKET
12204
44.REMOVE PCV VALVE SUB-ASSEMBLY
12101A
45.REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug and gasket.
12102A
46.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
15100
47.REMOVE OIL PUMP ASSEMBLY
11401L
48.REMOVE ENGINE REAR OIL SEAL
11420
49.REMOVE STIFFENING CRANKCASE ASSEMBLY
Uniformly loosen and remove the 11 bolts.
| *1 | Protective Tape |
Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block assembly.
Be careful not to damage the contact surfaces of the stiffening crankcase assembly and cylinder block assembly.
Tape the screwdriver tip before use.
11432A
50.REMOVE NO. 1 TAPER SCREW PLUG
Remove the No. 1 taper screw plug.
51.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
52.REMOVE STIFFENING CRANKCASE RING PIN
It is not necessary to remove a stiffening crankcase ring pin unless it is being replaced.