1.INSTALL FUEL EMISSION HOSE
Install the fuel emission hose.
Before connecting the fuel emission hose, check if there is any damage or foreign matter in the fuel emission hose or connector.
Check that the connector is connected by pulling on it.
Firmly push the tube connector until a "click" sound is heard.
77707
2.INSTALL CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY
Install the charcoal canister outlet tube sub-assembly to the fuel tank assembly and attach the 2 clamps.
77295D
3.INSTALL FUEL TUBE GROMMET
Install the 3 fuel tube grommets to the fuel tank assembly.
77299A
4.INSTALL NO. 5 FUEL TUBE CLAMP
Install the No. 5 fuel tube clamp to the fuel tank assembly.
77289B
5.INSTALL NO. 3 FUEL TUBE CLAMP
Install the No. 3 fuel tube clamp to the fuel tank assembly.
77026A
6.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Install the No. 1 fuel evaporation tube sub-assembly and attach the 5 clamps.
77209D
7.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY
Install the fuel tank main tube sub-assembly and attach the 5 clamps.
83320
8.INSTALL FUEL SENDER GAUGE ASSEMBLY
9.INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP
77168A
10.INSTALL FUEL TANK VENT TUBE SET PLATE
77209D
11.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
12.CONNECT FUEL EMISSION HOSE
77100
13.INSTALL FUEL TANK ASSEMBLY
Set the fuel tank assembly on an engine lifter with attachments.
Lift up the engine lifter.
Attach the wire harness to the 3 clamps.
Connect the fuel pump connector and sender gauge connector.
Be careful not to cut the wiring.
Install the No. 1 fuel tank band sub-assembly with the 2 bolts.
Install the No. 1 fuel tank band sub-assembly LH with the 2 bolts.
Install the No. 2 fuel tank band sub-assembly with the 2 bolts.
Attach the 3 wire harness clamps.
77014A
14.CONNECT NO. 3 FUEL TANK BREATHER TUBE SUB-ASSEMBLY
Connect the No. 3 fuel tank breather tube sub-assembly to the fuel tank.
Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>PRECAUTION
77707
15.CONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY
Connect the charcoal canister outlet tube sub-assembly to the fuel tank breather tube and slide the clamp to secure it.
Attach the hose clamp.
77213E
16.CONNECT FUEL TANK TO FILLER PIPE HOSE
| *1 | Range |
| *2 | Stopper |
| *3 | Protrusion |
| *a | Top of Vehicle |
| *b | Bottom of Fuel Tank |
Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the hose clamp.
Make sure the hose clamp is oriented as shown in the illustration.
77276
17.INSTALL FUEL HOSE PROTECTOR
Install the fuel hose protector to the fuel tank to filler pipe hose and attach the claw.
77026A
18.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Connect the No. 1 fuel evaporation tube sub-assembly and slide the clamp to secure it.
77209D
19.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Connect the fuel tank main tube sub-assembly.
Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>PRECAUTION
58398F
20.INSTALL NO. 1 FLOOR UNDER COVER
Attach the 2 clips and install the No. 1 floor under cover with the 2 nuts.
77641A
21.INSTALL NO. 1 FUEL TANK PROTECTOR
Attach the 3 clips and install the No. 1 fuel tank protector with the nut.
50819
22.INSTALL FRONT FLOOR COVER
Install the front floor cover and attach the 5 clips.
Install the bolt and nut.
23.CONNECT PARKING BRAKE CABLE
Connect the parking brake cable with the 2 bolts.
24.ADD FUEL
25.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
26.INSPECT FOR FUEL LEAK