Home › Engine / Hybrid System › 3ZR-FAE FUEL › FUEL INJECTOR
RM3090E _51 Engine / Hybrid System _008388 3ZR-FAE FUEL _0046819 FUEL INJECTOR A

3ZR-FAE FUEL  FUEL INJECTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A153011C08
1.063,0.385 0.729,0.385 false 2.042,1.365 2.396,1.365 false 0.521,0.292 0.708,0.469 0.188,0.177 10 *1 2.417,1.26 2.604,1.438 0.188,0.177 10 *2
*1 O-Ring
*2 Injector Vibration Insulator


Install a new injector vibration insulator and a new O-ring to each fuel injector assembly.


b.

Apply a light coat of gasoline or spindle oil to the O-ring of the fuel injector assembly.


c.
A153013

While turning the fuel injector assembly left and right, install it to the fuel delivery pipe sub-assembly.

NOTICE:
·

Do not twist the O-ring.

·

After installing the fuel injector assemblies, check that they turn smoothly. If not, replace the O-ring with a new one.




Hide 23807V 2.INSTALL NO. 1 DELIVERY PIPE SPACER

a.
A153008

Install the 2 No. 1 delivery pipe spacers to the cylinder head.

NOTICE:

Install the No. 1 delivery pipe spacers in the correct direction.



Hide 23807 3.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies, and then temporarily install the 2 bolts.

NOTICE:
·

Do not drop the fuel injector assemblies when installing the fuel delivery pipe sub-assembly.

·

Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe sub-assembly.




b.

Tighten the 2 bolts to the specified torque.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Install the bolt to secure the fuel delivery pipe sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Install the wire harness bracket with the bolt.

Torque:
7.7 N*m (79 kgf*cm, 68 in.*lbf)


Hide 23901 4.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly and install a new No. 2 fuel pipe clamp.

Click hereEngine / Hybrid System>3ZR-FAE FUEL>FUEL SYSTEM>PRECAUTION


Hide 5.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket with the 2 nuts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 74431 8.INSTALL BATTERY TRAY

Hide 28800 9.INSTALL BATTERY

Hide 74404A 10.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 11.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 12.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 14.INSPECT FOR FUEL LEAK

a.

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON, and push the GTS on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

iv.

Check that there are no leaks from the fuel system.


v.

Turn the ignition switch off.


vi.

Disconnect the GTS from the DLC3.



Hide 11212 15.INSTALL NO. 2 CYLINDER HEAD COVER