33242L
1.INSTALL SHIFT FORK SHAFT BEARING
Using SST and a press, press in 4 new shift fork shaft bearings.
0 to 0.5 mm (0 to 0.0196 in.)
33134B
2.INSTALL OUTPUT SHAFT COVER
| *a | Protrusion |
| *b | Groove |
Install the output shaft cover as shown in the illustration.
33322B
3.INSTALL FRONT NO. 2 OUTPUT SHAFT BEARING OUTER RACE
Using SST and a hammer, tap in the front No. 2 output shaft bearing outer race.
33134B
4.INSTALL OUTPUT SHAFT COVER
| *a | Protrusion |
| *b | Groove |
Install the output shaft cover as shown in the illustration.
33321N
5.INSTALL FRONT OUTPUT SHAFT BEARING
Using SST and a press, install a new front output shaft bearing to the front transaxle case.
Install the bearing lock plate and bolt.
Coat a front output shaft bearing with gear oil.
31105H
6.INSTALL TRANSMISSION CASE OIL SEAL
Using SST and a hammer, install a new transaxle case oil seal to the front transaxle case.
4.4 to 5.0 mm (0.174 to 0.196 in.)
Coat the lip of the transaxle case oil seal with MP grease.
33311A
7.INSTALL FRONT INPUT SHAFT BEARING
Using SST and a press, install a new front input shaft bearing to the front transaxle case.
Install the bearing lock plate and bolt.
Coat the front input shaft bearing with gear oil.
33311P
8.INSTALL REAR INPUT AND OUTPUT SHAFT BEARING SHAFT SNAP RING
Using a snap ring expander, install the 2 rear input and output shaft bearing shaft snap rings.
33261K
9.INSTALL SHIFT AND SELECT LEVER SHAFT NEEDLE ROLLER BEARING
Using SST and a press, press in a new shift and select lever shaft needle roller bearing.
177.8 to 178.7 mm (7.00 to 7.03 in.)
33242L
10.INSTALL SHIFT FORK SHAFT BEARING
Using SST and a press, press in 4 new shift fork shaft bearings to the manual transmission case.
168.2 to 169.3 mm (6.63 to 6.66 in.)
162.2 to 163.3 mm (6.39 to 6.42 in.)
41311E
11.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
Using SST and a hammer, tap in the front differential case front tapered roller bearing.
41311F
12.INSTALL FRONT DIFFERENTIAL CASE REAR OUTER RACE BEARING
Install the front differential case rear shim into the manual transmission case.
Using SST and a hammer, install the front differential case rear outer race bearing.
33111J
13.INSTALL MANUAL TRANSMISSION CASE STRAIGHT PIN
| *a | Protrusion |
Using a plastic-faced hammer, tap in the 4 new straight pins to the front transaxle case.
10.5 to 11.5 mm (0.414 to 0.452 in.)
14.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD
Coat the front differential case assembly with gear oil and install it to the front transaxle case.
Install the manual transmission case to the front transaxle case with the 12 bolts.
Install the 6 bolts to the front transaxle case side.
Turn the differential case in both directions and make sure it turns smoothly.
| *a | Mark |
Using SST and a torque wrench, measure the starting preload.
0.96 to 2.38 N*m (9.8 to 24.2 kgf*cm, 8.5 to 21.0 in.*lbf)
If the preload is not as specified, replace the front differential case rear shim with one of a different thickness. Use the table below to select a front differential case rear shim which will ensure that the preload is within the specification.
| Mark | Specified Condition | Mark | Specified Condition |
|---|---|---|---|
| 0 | 2.00 mm (0.0787 in.) | 9 | 2.45 mm (0.0965 in.) |
| 1 | 2.05 mm (0.0807 in.) | A | 2.50 mm (0.0984 in.) |
| 2 | 2.10 mm (0.0827 in.) | B | 2.55 mm (0.1004 in.) |
| 3 | 2.15 mm (0.0846 in.) | C | 2.60 mm (0.1024 in.) |
| 4 | 2.20 mm (0.0866 in.) | D | 2.65 mm (0.1043 in.) |
| 5 | 2.25 mm (0.0886 in.) | E | 2.70 mm (0.1063 in.) |
| 6 | 2.30 mm (0.0906 in.) | F | 2.75 mm (0.1083 in.) |
| 7 | 2.35 mm (0.0925 in.) | G | 2.80 mm (0.1102 in.) |
| 8 | 2.40 mm (0.0945 in.) | H | 2.85 mm (0.1122 in.) |
Remove the 18 bolts and manual transmission case.
33322A
15.INSTALL REAR NO. 2 OUTPUT SHAFT BEARING OUTER RACE
| *a | Mark |
Install the rear output shaft bearing shim to the manual transmission case.
When reusing the output shaft rear tapered roller bearing, first install a shim of the same thickness as the original. When installing a new output shaft front bearing, first select and install a rear output shaft bearing shim which is thinner than the original.
Using SST and a hammer, install the rear No. 2 output shaft bearing outer race.
16.ADJUST REAR NO. 2 OUTPUT SHAFT BEARING PRELOAD
Install the No. 2 output shaft assembly and front differential case assembly to the front transaxle case.
Install the manual transmission case to the front transaxle case with the 12 bolts.
Install the 6 bolts to the front transaxle case side.
Using SST and a torque wrench, measure the rear No. 2 output shaft bearing preload. Subtract the value of the differential side bearing preload from the measured rear No. 2 output shaft bearing preload.
4.36 to 6.17 N*m (45 to 62 kgf*cm, 39 to 54 in.*lbf)
If the preload is not as specified, replace the shim with one of a different thickness. Use the table below to select a shim which will ensure that the preload is within the specification.
| Mark | Specified Condition | Mark | Specified Condition |
|---|---|---|---|
| A | 1.80 mm (0.0709 in.) | K | 2.25 mm (0.0866 in.) |
| B | 1.85 mm (0.0723 in.) | L | 2.30 mm (0.0906 in.) |
| C | 1.90 mm (0.0748 in.) | M | 2.35 mm (0.0925 in.) |
| D | 1.95 mm (0.0768 in.) | N | 2.40 mm (0.0945 in.) |
| E | 2.00 mm (0.0787 in.) | P | 2.45 mm (0.0965 in.) |
| F | 2.05 mm (0.0809 in.) | Q | 2.50 mm (0.0984 in.) |
| G | 2.10 mm (0.0827 in.) | R | 2.55 mm (0.1004 in.) |
| H | 2.15 mm (0.0846 in.) | S | 2.60 mm (0.1024 in.) |
| J | 2.20 mm (0.0866 in.) | T | 2.65 mm (0.1043 in.) |
Remove the 18 bolts and manual transmission case.
Remove the No. 2 output shaft assembly from the front transaxle case.
Remove the front differential assembly case from the front transaxle case.
33449
17.INSTALL TRANSMISSION MAGNET
Clean and install the transmission magnet to the front transaxle case.
41301L
18.INSTALL FRONT DIFFERENTIAL CASE ASSEMBLY
Coat the front differential case assembly with gear oil, and install it to the front transaxle case.
33176B
19.INSTALL TRANSMISSION OIL SEPARATOR
for Front Transaxle Case Side:
Install the transmission oil separator to the front transaxle case with the 2 bolts.
33311
20.INSTALL INPUT SHAFT, NO. 1 OUTPUT SHAFT ASSEMBLY AND NO. 2 OUTPUT SHAFT ASSEMBLY
Install the 3 shafts at the same time.
33461
21.INSTALL REVERSE IDLER GEAR
Coat the reverse idler gear, needle roller bearing and reverse idler thrust washer with MP grease, and install them to the reverse idler gear shaft.
Make sure that the protruding part of the reverse idler thrust washer fits into the groove of the reverse idler shaft.
Install the reverse idler gear shaft by sliding and lifting it.
| *a | Align the Mark |
Align the mark of the reverse idler gear shaft with the hole of the bolt.
33211
22.INSTALL REVERSE SHIFT FORK
Install the reverse shift fork to the No. 2 output shaft assembly.
33214G
23.INSTALL NO. 3 GEAR SHIFT FORK
Install the No. 3 gear shift fork to the No. 2 output shaft assembly.
33244J
24.INSTALL 5TH AND 6TH SHIFT FORK SHAFT
Install the 5th and 6th shift fork shaft to the front transaxle case.
Coat the threads of the bolt with adhesive.
Toyota Genuine Adhesive 1344, Three Bond1344 or equivalent
Install the bolt to the No. 3 gear shift fork.
33245H
25.INSTALL REVERSE SHIFT FORK SHAFT
Install the reverse shift fork shaft to the front transaxle case.
Coat the threads of the bolt with adhesive.
Toyota Genuine Adhesive 1344, Three Bond1344 or equivalent
Install the bolt to the reverse gear shift fork.
33222F
26.INSTALL SHIFT ARM
Install the shift arm to the front transaxle case.
33212A
27.INSTALL NO. 1 GEAR SHIFT FORK
Install the No. 1 gear shift fork to the No. 1 output shaft assembly.
33246C
28.INSTALL NO. 5 GEAR SHIFT FORK SHAFT
Install the No. 3 gear shift head to the No. 5 gear shift fork shaft.
Using a 5 mm pin punch and hammer, tap a new pin into the No. 3 gear shift head.
-0.5 to 0.5 mm (-0.0197 to 0.0196 in.)
Install the No. 5 gear shift fork shaft to the front transaxle case.
Connect the shift arm to the No. 5 gear shift fork shaft.
Install the pin to the shift arm.
Using a brass bar and hammer, tap a new E-ring to the pin.
33213G
29.INSTALL NO. 2 GEAR SHIFT FORK
Install the No. 2 gear shift fork to the No. 1 output shaft assembly.
33243F
30.INSTALL 3RD AND 4TH SHIFT FORK SHAFT
Install the No. 2 gear shift head to the 3rd and 4th shift fork shaft.
Install the 3rd and 4th shift fork shaft to the front transaxle case.
Using a 5 mm pin punch and hammer, tap a new pin into the No. 2 gear shift fork.
-0.5 to 0.5 mm (-0.0197 to 0.0196 in.)
Using a 5 mm pin punch and hammer, tap a new pin into the No. 2 gear shift head.
-0.5 to 0.5 mm (-0.0197 to 0.0196 in.)
33242F
31.INSTALL 1ST AND 2ND SHIFT FORK SHAFT
Install the 1st and 2nd shift fork shaft to the front transaxle case.
Coat the threads of the bolt with adhesive.
Toyota Genuine Adhesive 1344, Three Bond1344 or equivalent
Install the bolt to the No. 1 gear shift fork.
33176B
32.INSTALL TRANSMISSION OIL SEPARATOR
for Manual Transmission Case Side:
Install the transmission oil separator to the manual transmission case with the 2 bolts.
33124C
33.INSTALL NO. 1 OIL RECEIVER PIPE
Install the No. 1 oil receiver pipe to the manual transmission case.
Do not damage the No. 1 oil receiver pipe.
33111
34.INSTALL MANUAL TRANSMISSION CASE
Clean the contact surface of the manual transmission case and front transaxle case with non-residue solvent.
| *a | Seal Packing |
Apply seal packing to the manual transmission case as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
1.2 mm (0.0472 in.)
Assemble parts within 10 minutes of application. Otherwise, the seal packing must be removed and reapplied.
Using 2 pairs of snap ring pliers to keep the snap ring stretched, install the manual transmission case.
| *a | 8.5 mm (0.3346 in.) |
| *b | 9.3 mm (0.3661 in.) |
Install a bolt to the No. 1 output shaft assembly and lift the No. 1 output shaft assembly from the service hole. Make sure that the output shaft rear bearing shaft snap ring and input shaft bearing shaft snap ring are positioned correctly in the bearing grooves by checking that the distances between the centers of snap ring holes are as shown in the illustration.
Install the manual transmission case to the front transaxle case with the 12 bolts.
Install the 6 bolts to the front transaxle case.
35.INSTALL REVERSE IDLER GEAR SHAFT BOLT
Coat the reverse idler gear shaft bolt with adhesive, and install a new gasket and the shaft bolt.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
33275C
36.INSTALL SHIFT DETENT BALL
Clean the threads of the 4 detent ball plugs.
Apply a few drops of adhesive to 2 or 3 threads of each of the 4 detent ball plugs.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Using a 6 mm hexagon wrench, install the 4 shift detent balls, 4 shift detent ball compression springs, 4 No. 1 shift ball spring seats and 4 detent ball plugs.
33111A
37.INSTALL MANUAL TRANSMISSION CASE PLUG
Clean the contact surface of the manual transmission case and manual transmission case plug.
| *a | Seal Packing |
Apply seal packing to the manual transmission case as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Apply a few drop of the adhesive to 2 or 3 threads of the manual transmission case plug.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the manual transmission case plug to the manual transmission case.
33403L
38.INSTALL O-RING
Coat a new O-ring with MP grease, and install it to the shift and select lever shaft straight pin (B).
33261F
39.INSTALL SHIFT AND SELECT LEVER SHAFT STRAIGHT PIN
Install the spring.
While pressing in the shift and select lever shaft straight pin (A) in as far as it will go, push in the shift and select lever shaft straight pin (B) to install it.
33101A
40.INSTALL MANUAL TRANSMISSION FILLER PLUG
Install a new gasket and the manual transmission filler plug.
33104
41.INSTALL DRAIN PLUG
Install a new gasket and the drain plug.
31105H
42.INSTALL TRANSMISSION CASE OIL SEAL
31105H
43.INSTALL TRANSAXLE CASE OIL SEAL
33251A
44.INSTALL SHIFT AND SELECT LEVER ASSEMBLY
Align the 4 shift fork shafts as shown in the illustration.
Clean the contact surface of the manual transmission case and shift and select lever assembly.
Clean the threads of the bolts with non-residue solvent.
| *a | Seal Packing |
Apply seal packing to the manual transmission case as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Apply a few drops of adhesive to 2 or 3 threads of the 4 bolts.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the shift and select lever assembly to the manual transmission case with the 4 bolts.
33295B
45.INSTALL SHIFT GATE PIN
Apply a few drops of the adhesive to 2 or 3 threads of the shift gate pin.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the shift gate pin to the manual transmission case.
33290B
46.INSTALL NO. 2 LOCK BALL ASSEMBLY
Clean the threads of the No. 2 lock ball assembly with non-residue solvent.
Apply a few drops of the adhesive to 2 or 3 threads of the No. 2 lock ball assembly.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the No. 2 lock ball assembly to the manual transmission case.
33290
47.INSTALL NO. 1 LOCK BALL ASSEMBLY
Clean the threads of the No. 1 lock ball assembly with non-residue solvent.
Apply a few drops of the adhesive to 2 or 3 threads of the No. 1 lock ball assembly.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Install the No. 1 lock ball assembly to the manual transmission case.
33101Q
48.INSTALL NO. 1 TRANSMISSION CASE PLUG
Coat the No. 1 transmission case plug with adhesive.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Using a T55 ''TORX'' socket wrench, install the No. 1 transmission case plug.
84210
49.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
Using SST, install a new gasket and the back-up light switch assembly to the manual transmission case.
33590F
50.INSTALL FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY
Install the floor shift selecting bell crank assembly to the manual transmission case with the 2 bolts.
33524B
51.INSTALL CONTROL CABLE BRACKET
Install the control cable bracket to the manual transaxle assembly with the 3 bolts.
31236B
52.INSTALL RELEASE FORK SUPPORT
31126
53.INSTALL CLUTCH RELEASE FORK BOOT
Install the clutch release fork boot to the front transaxle assembly.
31230
54.INSTALL CLUTCH RELEASE BEARING ASSEMBLY
31204
55.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY