This DTC is stored when a malfunction occurs in the DAB tuner antenna which is connected to the radio and display receiver assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B157D | DAB Tuner Antenna Disconnected | The DAB tuner antenna is not connected | ·
Roof antenna pole sub-assembly ·
Antenna with holder assembly ·
No. 3 antenna cord sub-assembly ·
No. 2 antenna cord sub-assembly ·
Antenna cord sub-assembly ·
Radio and display receiver assembly |
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
Check for DTCs.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check if any optional components that may decrease reception capacity, such as a telephone antenna, are installed.
Optional components are installed.
Do not remove optional components without permission of the customer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna connector from the radio and display receiver assembly.
Turn the ignition switch to ACC with the radio and display receiver assembly connector connected.
Turn on the radio and turn into AM mode.
Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.
Noise occurs.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Antenna with Holder Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the antenna with holder assembly.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | Below 1 Ω |
| 1-a - 2-a | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 1-a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 3 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
Disconnect the antenna connector from the No. 3 antenna cord sub-assembly.
Disconnect the antenna connector from the antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 1 | Always | Below 1 Ω |
| 2-a - 1-a | Always | Below 1 Ω |
| 2 - Body ground | Always | 10 kΩ or higher |
| 2-a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Disconnect the antenna connector from the radio and display receiver assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 1 | Always | Below 1 Ω |
| 1-a - 1-a | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 1-a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD(for Instrument Panel Side)>REMOVAL
Check that the roof antenna pole sub-assembly is securely installed.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>INSTALLATION
The roof antenna pole sub-assembly is installed properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the antenna with holder assembly with a known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA HOLDER>REMOVAL
Clear the DTCs.
Check for DTCs.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG