Home › Drivetrain › K114F MULTIDRIVE / CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2015.04–2015.10
RM3090E _52 Drivetrain _036009 K114F MULTIDRIVE / CVT _0166287 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0841  Transmission Fluid Pressure Sensor "A" Performance  P2829  Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS)  


DESCRIPTION

The ECM controls the secondary oil pressure calibration based on the secondary oil pressure signal output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0841 Transmission Fluid Pressure Sensor "A" Performance 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

The requested oil pressure value is 1.4 MPa (14.3 kgf/cm2, 203 psi) or higher.

2.

The oil pressure sensor output value is below 0.5 MPa (5.1 kgf/cm2, 73 psi).

3.

2 seconds

4.

1-trip detection logic


DTC Detection Condition 2:
1.

The requested oil pressure value is below 1.0 MPa (10.2 kgf/cm2, 145 psi).

2.

The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or higher.

3.

3 seconds

4.

1-trip detection logic


·

Oil pressure sensor

·

ECM


Comes on DTC stored
P2829 Pressure Control Solenoid "K" Performance (Shift Solenoid Valve SLS) 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

The requested oil pressure value is below 1.0 MPa (10.2 kgf/cm2, 145 psi).

2.

The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or higher.

3.

3 seconds

4.

1-trip detection logic


DTC Detection Condition 2:
1.

The shift lever is in D, and the vehicle speed is less than 8 km/h (5 mph).

2.

The ratio of the transmission revolution sensor (NIN) speed and the transmission revolution sensor (NOUT) speed exceeds a specified value.

3.

0.2 seconds

4.

1-trip detection logic


DTC Detection Condition 3:
1.

The oil pressure sensor output value is below 0.283 MPa (2.9 kgf/cm2, 41 psi) and the target gear ratio is 2.0 or more.

2.

The actual gear ratio is less than 1.0.

3.

1.5 seconds or more

4.

1-trip detection logic


·

Continuously variable transaxle assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM checks for belt clamping high-pressure or low-pressure errors. If a mechanical malfunction is detected in the shift solenoid valve SLS or the oil pressure sensor, the ECM detects the problem, illuminates the MIL and stores a DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0841 AND P2829)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.

HINT:

If any other DTCs besides P0841 or P2829 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Both DTC P0841 and P2829 are output A
Only DTC P0841 is output B
Only DTC P2829 is output C
P0841 and/or P2829 and other DTCs are output D



A

2.READ VALUE USING GTS (A/T OIL PRESSURE)

B

12.READ VALUE USING GTS (A/T OIL PRESSURE)

C

19.READ VALUE USING GTS (A/T OIL PRESSURE)

D

2.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:

The stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be conducted after checking and confirming that the engine is operating normally.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform this test with the A/C off.

·

Do not perform the stall speed test for longer than 5 seconds.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


h.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 4.5 MPa (35.7 to 45.9 kgf/cm2, 508 to 653 psi): D position stall speed test

·

2.5 to 4.5 MPa (25.5 to 45.9 kgf/cm2, 363 to 653 psi): R position stall speed test

·

0.140 to 0.400 MPa (1.4 to 4.1 kgf/cm2, 20 to 58 psi): With shift lever in D, engine is stopped by start and stop system (oil pump assembly with motor is operating)


-
Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

3.REPLACE ECM

B

4.REPLACE OIL PRESSURE SENSOR
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Result:
Proceed to
NEXT




NEXT

6.PERFORM INITIALIZATION
6.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)



·

After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P0841 and/or P2829 is output A
DTCs are not output B



A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.PERFORM INITIALIZATION
9.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)



·

After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
10.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P2829 is output A
DTCs are not output B



A

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

END

11.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:

The stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be conducted after checking and confirming that the engine is operating normally.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform this test with the A/C off.

·

Do not perform the stall speed test for longer than 5 seconds.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


h.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 4.5 MPa (35.7 to 45.9 kgf/cm2, 508 to 653 psi): D position stall speed test

·

2.5 to 4.5 MPa (25.5 to 45.9 kgf/cm2, 363 to 653 psi): R position stall speed test

·

0.140 to 0.400 MPa (1.4 to 4.1 kgf/cm2, 20 to 58 psi): With shift lever in D, engine is stopped by start and stop system (oil pump assembly with motor is operating)


-
Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

13.REPLACE ECM

B

14.REPLACE OIL PRESSURE SENSOR
13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC
a.

Clear the DTCs.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Result:
Proceed to
NEXT




NEXT

16.PERFORM INITIALIZATION
16.PERFORM INITIALIZATION
NOTICE:
·

Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:

Replaced Part
·

Continuously variable transaxle assembly

·

ECM

·

Oil pressure sensor

·

Yaw rate and acceleration sensor (Airbag sensor assembly)



·

After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

17.CHECK DTC OUTPUT
17.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTC P0841 is output A
DTCs are not output B



A

18.REPLACE ECM

B

END

18.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

19.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:

The stall speed test should always be performed with at least 2 people. One person should observe the condition of the wheels and wheel chocks while the other is performing the test.


NOTICE:
·

This test must be conducted after checking and confirming that the engine is operating normally.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform this test with the A/C off.

·

Do not perform the stall speed test for longer than 5 seconds.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.


h.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.5 to 4.5 MPa (35.7 to 45.9 kgf/cm2, 508 to 653 psi): D position stall speed test

·

2.5 to 4.5 MPa (25.5 to 45.9 kgf/cm2, 363 to 653 psi): R position stall speed test

·

0.140 to 0.400 MPa (1.4 to 4.1 kgf/cm2, 20 to 58 psi): With shift lever in D, engine is stopped by start and stop system (oil pump assembly with motor is operating)


-
Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

20.REPLACE ECM

B

21.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
20.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

21.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
a.

Replace the continuously variable transaxle assembly.

Click hereDrivetrain>K114F MULTIDRIVE / CVT>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT